Customer Service 800-967-6696 | http://www.crateandbarrel.com
MADISON BUFFET
Thank you for purchasing the Madison Buffet. This
page
lists all the contents included in the box. Please
take the time to identify the hardware as well as the
individual components
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
to this product. As you unpack
COMPONENTS
1 - top panel
1 - large
back panel
1 - bottom panel
2 - aprons
2 - side
panels
2 - side aprons
Made in Denmark R06
3 - cabinet pulls
1 - panel
connector
HARDWARE
4 - glides
6 - case
hinges
4 - support
wedges
4 - adhesive
pads
6 - door
hinges
2 - plastic
brackets
TOOLS REQUIRED
Phillips head screwdriver
2 - small
back panels
1 - middle
partition
8 - shelf
pegs
screws
12 - cam
covers
door panels
1 - large shelf
1 - small shelf
20 - cam
screws
20 - cams22 - small
Missing hardware?
Please call 800.606.6387
for replacements.
hammer
8 - large
screws
34 - wood
dowels
4 - legs3 - front
Page 1 of 5
Customer Service 800-967-6696 | http://www.crateandbarrel.com
MADISON BUFFET
A. Insert 1 cam screw per leg and tighten with a
1
phillips head screwdriver.
B. Insert 2 wood dowels into the ends of each long apron.
C. Insert 2 cams into the face of each long apron.
Make sure the arrow on each cam points to the
closest short end of the the apron.
Repeat assembly method in Steps 1 and 2 for the
3
attachment of the 2 short aprons, using 4 wood dowels, 2 cam screws, and 2 cams per apron.
Secure all cams with a phillips head screwdriver.
Made in Denmark R06
B
A
C
A
B
A. Fit 1 leg on the end of each long apron, aligning
2
dowels and cam screws with corresponding holes.
B. Secure legs by turning each cam 180º clockwise
with a phillips head screwdriver.
A
A) Align pre-drilled holes on apron with pre-drilled
4
holes on bottom panel. Insert 8 large screws
through front, back and side aprons into bottom
panel as shown. Secure each screw with a phillips
head screwdriver.
C) Using a hammer, gently tap in 1 glide onto the
bottom of each leg.
B
Page 2 of 5
Customer Service 800-967-6696 | http://www.crateandbarrel.com
MADISON BUFFET
Top
Panel
A) Position assembled unit upright. Insert 6 cam screws
5
to the bottom panel as illustrated. Secure with a phillips head screwdriver.
B) Attach 6 cam screws and 2 plastic brackets to the
underside of top panel. Set top panel aside.
Make sure
case hinges
face inwards
A) Insert 6 wood dowels into 2 side panels and 1
7
middle partition. Press firmly to secure.
B) Fit 2 side panels and 1 middle partition onto cam
screws and bottom panel. Using a phillips head
screwdriver, turn bottom 6 cams 180º clockwise to
secure panels as illustrated above.
Made in Denmark R06
A
B
Side
Panel
Middle
Partition
Side
Panel
A) Insert 4 cams into 2 side panels and 1 middle
6
partition. Make sure arrows on each cam point
towards the short end of each panel.
B) Attach 2 case hinges to 2 side panels and 1 middle partition with 2 small screws per hinge. Secure all screws
with a phillips head screwdriver.
A
B
B
A
A
8
A) Slide large and small back panels into grooves at
rear of side panels and middle partition.
B) Slide panel connector between 2 small back panels.
Page 3 of 5
Customer Service 800-967-6696 | http://www.crateandbarrel.com
MADISON BUFFET
A
B
Carefully position top panel over assembled unit.
9
Align cam screws and wood dowels with
corresponding holes in the top and side panels.
Make sure the top panel brackets face the front of
the assembled unit.
A) Attach 2 door hinges to 3 door panels with 2
11
small screws per hinge. Secure all screws with a
phillips head screwdriver.
B) Adhere 1 adhesive pad to top corner of each door panel opposite of case hinge, as illustrated above.
Made in Denmark R06
x 4
Position 4 support wedges onto the back edges of
10
the assembled unit as shown. Secure each support
wedge with 1 small screw.
B
A
x 6
A) Attach 3 front door panels to assembled unit. Fit
12
each door hinge into corresponding case hinge and
secure by tightening preinstalled screws in case hinge
with a screwdriver.
B) Insert 8 shelf pins to side panels and middle partition at desired shelf height (adjustable).
Page 4 of 5
Customer Service 800-967-6696 | http://www.crateandbarrel.com
MADISON BUFFET
Position 1 large shelf and 1 small shelf onto shelf
13
pegs in assembled unit.
15
Attach 12 cam covers onto cams, as illustrated above.
Press firmly to secure. Assembly is now complete.
Made in Denmark R06
Attach 3 door pulls to 3 door panels with 2 small
14
screws per door. Using a Phillips head screwdriver,
turn screws clockwise to secure.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as the
wood is finished with a protective clear lacquer.
Page 5 of 5
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.