LOOP 6 DRAWER DRESSER
HARDWARE
Thank you for purchasing the Loop 6 Drawer Dresser.
This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
NOTE: 2 people are required to safely assemble this
product.
COMPONENTS
24 - cams
17 - wood
dowels
Missing hardware? Please call 800.606.6387 for replacements.
24 - cam
screws
24 - cam
covers
12 - silver
screws
24 - glide
screws
13 - black
screws
6 - pulls
TOOLS REQUIRED
Phillips Head Screwdriver
1 - top panel
2 - side frames
(1 left, 1 right)
Made in China r11 Page 1 of 5
partition
Customer Service 800.967.6696 | www.crateandbarrel.com
1 - crossbar
6 - drawer backs
12 - drawer sides
(6 right, 6 left)
1 - back panel
LEFT
RIGHT
6 - drawer fronts
(3 labeled LEFT, 3 labeled RIGHT on
back of drawer fronts)
6 - drawer bottoms1 - middle
LOOP 6 DRAWER DRESSER
Arrow on each
cam points towards
edge with holes
B
A
C
1 A) Place left side panel face down on a padded surface.
Insert 4 cam screws into the holes as shown. Secure, but do
not over tighten with a phillips head screwdriver.
B) Insert 3 cams into the large holes as shown, making sure
the arrow on each cam points towards the nearest edge with
holes.
C) Insert 2 wood dowels into the top edge of the panel.
Repeat Steps A, B & C for the right side panel.
A
Back Panel
Crossbar
B
2 A) Insert 6 wood dowels, 3 cam screws, and 10 cams
into back panel as shown.
B) Insert 2 wood dowels and 2 cams into crossbar as shown.
middle
partition
middle
partition
3 Insert 5 wood dowels and 6 cams into middle partition
as shown.
Made in China r11 Page 2 of 5
Customer Service 800.967.6696 | www.crateandbarrel.com
4 Fit cam screws of back panel into corresponding holes in
the middle partition.
back
panel
LOOP 6 DRAWER DRESSER
middle
partition
5 Secure 3 cams at the base of the middle partition with a
Phillips head screwdriver. Turn each cam clockwise until it
securely engages each cam screw.
crossbar
middle
partition
6 Carefully turn the middle partition and back panel
assembly on end as shown. Fit dowel of middle partition
into corresponding hole of crossbar. Secure crossbar with 1
black screw as shown, using a Phillips head screwdriver.
right side
panel
7 Fit cam screws of right side panel into corresponding
holes of back panel and crossbar. Secure cams with a
Phillips head screwdriver.
left side
panel
8 Fit cam screws of left side panel into corresponding
holes of back panel and crossbar. Secure cams with a
Phillips head screwdriver.
Made in China r11 Page 3 of 5
Customer Service 800.967.6696 | www.crateandbarrel.com
LOOP 6 DRAWER DRESSER
top
panel
9 Insert 13 cam screws into the underside of the top panel
as shown.
top
panel
10 With assistance of another adult, position assembled
unit upright. Fit cam screws of top panel into corresponding
holes of assembled unit as shown. Secure all cams with a
Phillips head screwdriver.
11 Slide left and right drawer sides up into slots on back
of the drawer front. Make sure glide hardware is on the
outside of the drawer sides and the vertical slots are at the
back of the assembly as shown.
Made in China r11 Page 4 of 5
Customer Service 800.967.6696 | www.crateandbarrel.com
12 Slide drawer back into vertical slots at rear of drawer
sides.
LOOP 6 DRAWER DRESSER
These holes at back
12 Slide drawer bottom into slot at base of drawer
sides and drawer front. Make sure pilot holes are at the
back of the drawer bottom as shown.
B
A
13 A) Secure underside of drawer bottom to drawer
back with 2 black screws. Secure, but do not over
tighten with the phillips head screwdriver.
B) Fit drawer pull into position as shown and secure with
2 silver screws.
Repeat Steps 8 - 11 for remaining 5 drawers.
14 A) Fully extend drawer glides from
assembled unit as shown.
B) Position drawer assembly and rest the
drawer assembly on top of the tabs as
shown. Attach each glide to drawer with 2
glide screws as shown. Secure with a
screwdriver. Repeat steps for each drawer.
C) Conceal all exposed cams with cam
covers.
Assembly is now complete.
NOTE: Drawers labeled “LEFT”
on the back of drawer front are to
be placed into the left side of the assembly.
Drawers labeled “RIGHT” are to be placed
into the right side of the assembly.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not
use abrasive cleaners. Do not use furniture wax or
polish as the wood is finished with a protective clear
lacquer.
A
B
B
C
Made in China r11 Page 5 of 5
Customer Service 800.967.6696 | www.crateandbarrel.com
Loading...