Page 1
LOOP NIGHTSTAND
HARDWARE
Thank you for purchasing the Loop Nightstand. This
page lists all the contents included in the box. Please
take time to identify the hardware as well as the individual
components of this product. As you unpack and prepare
for assembly, place the contents on a carpeted or
padded area to protect them from damage.
COMPONENTS
16 - cams
18 - wood
dowels
Missing hardware? Please call 800.606.6387 for replacements.
16 - cam
screws
16 - cam
covers
2- silver
screws
screws
2 - black
screws
1 - pull4 - glide
TOOLS REQUIRED
Phillips Head Screwdriver
1 - top panel
2 - side frames
(1 left, 1 right
Made in China - r11 Page 1 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
1 - shelf
1 - crossbar
1 - drawer back
1 - back panel
2 - drawer sides
(1 right, 1 left)
1 - drawer front
1 - drawer bottom
Page 2
LOOP NIGHTSTAND
Arrow on each
cam points towards
edge with holes
A
B
C
1 A) Place left side panel face down on a padded surface.
Insert 5 cam screws into the holes as shown. Secure, but do
not over tighten with a phillips head screwdriver.
B) Insert 2 cams into the large holes as shown, making sure
the arrow on each cam points towards the nearest edge with
holes.
C) Insert 2 wood dowels into the holes as shown. Press
firmly to secure.
Repeat Steps A & B for the right side panel.
Back Panel
A
Shelf
B
Crossbar
C
2 A) Insert 6 wood dowels and 6 cams into back panel as
shown.
B) Insert 6 wood dowels and 4 cams into shelf as shown.
C) Insert 2 wood dowels and 2 cams into crossbar as shown.
A
B
Cam in
unlocked
position
3 A) Fit dowels of shelf into corresponding holes in back
panel.
B) Carefully align shelf assembly with cam screws of left side
frame and firmly fit into position.
Made in China - r11 Page 2 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
4 Secure 2 cams at the base of the shelf assembly and 2
cams along the side of the back panel with a phillips head
screwdriver. Turn each cam clockwise until it securely
engages each cam screw.
Cam in
locked
position
Page 3
LOOP NIGHTSTAND
5 Fit the crossbar onto cam screw of the side panel as
shown. Secure the cam by turning clockwise with a phillips
head screwdriver.
A
6 Fit cam screws of right side panel into corresponding
holes in the assembly. Secure each cam with a phillips head
screwdriver.
B
7 A) Insert 6 cam screws into the underside of the top
panel.
B) Place assembly upright. Fit top panel onto dowels of the
assembly and secure each cam with a phillips head screw-
driver.
Made in China - r11 Page 3 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
8 Slide left and right drawer sides up into slots on back of
the drawer front. Make sure glide hardware is on the outside
of the drawer sides and the vertical slots are at the back of
the assembly as shown.
Page 4
LOOP NIGHTSTAND
These holes at back
9 Slide drawer back into vertical slots at rear of drawer
sides.
10 Slide drawer bottom into slot at base of drawer sides
and drawer front. Make sure pilot holes are at the back of the
drawer bottom as shown.
C
B
A
B
B
A
11 A) Secure underside of drawer bottom to drawer back
with 2 black screws. Secure, but do not over tighten with
the phillips head screwdriver.
B) Fit drawer pull into position as shown and secure with 2
silver screws.
Made in China - r11 Page 4 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
12 A) Fully extend drawer glides from assembled unit as
shown.
B) Position drawer assembly and rest the drawer assembly
on top of the tabs as shown. Attach each glide to drawer with
2 glide screws as shown. Secure with a screwdriver.
C) Conceal all exposed cams with cam covers.
Assembly is now complete.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as the
wood is finished with a protective clear lacquer.
Loading...