Crate & Barrel Loop File and Hutch Top Assembly Instruction

LOOP FILE PEDESTAL
HARDWARE
Missing hardware? Please call
800.606.6387 for replacements.
Thank you for purchasing the Loop File Pedestal. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
4 - pull screws
1 - small screw
2 - file rails
TOOLS REQUIRED
phillips head screwdriver
COMPONENTS
1 - file cabinet
1 - large screw
1 - plastic anchor
1 - wall strap
2 - pulls
file cabinet
pull
1 Pull out each drawer from file cabinet. Attach 1 pull to each drawer with 2 screws as shown. Secure screws with a phillips head screwdriver.
foam
drawer assembly
foam
2 Please remove packing foam located between each drawer assembly and file cabinet as shown. If packing foam is difficult to remove, detach drawer assembly from drawer glides. For instructions on removing/attaching
drawer assembly, refer to diagram on page 2.
file cabinet
Made in China - r07 Page 1 of 2
Customer Service 800.967.6696 | www.crateandbarrel.com
LOOP FILE PEDESTAL
A
Insert file rails into outer notches
Insert file rails into inner notches
A
Legal Hanging Files
B
Letter Hanging Files
3 A) For legal hanging files, insert file rails into outer
notches as shown, and fit file hooks over file rails. B) For letter hanging files, insert file rails into inner notches as shown, and fit hooks over file hooks over file rails. Assembly is now complete.
SAFETY MOUTNING INSTRUCTIONS
left drawer glide
B
A
B
A) Remove drawer assembly from file pedestal: Fully extend drawer assembly from file cabinet. Locate plastic tabs on left and right drawer glides. With even pressure, simutaneously lift the left tab (A) and press the right tab (B) to release drawer assembly from assembled unit.
B) Attach drawer assembly to file pedestal: Fully extend drawer glides from file cabinet. Fit drawer glides of drawer assembly into corresponding drawer glides of file cabinet. Push drawer assembly forward and listen for a click to ensure that assembly is secure.
NOTE: Insert screws 3/4"-1" from the edge of the strap
right drawer glide
A. Drill a hole in the wall slightly smaller than the diameter of the plastic anchor. Lightly tap with a hammer until the face is flush with
small screw
wall strap
WALL
the wall. B. Insert large screw through wall strap and into the wall anchor.
plastic anchor
C. Insert small screw through wall anchor strap and into the top of unit. Mounting assembly is now complete.
large screw
NOTE: If you are unsure about your wall type or what mounting method you should use, consult a qualified professional or your local hardware store.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the wood is finished with a protective clear lacquer.
Made in China - r07 Page 2 of 2
Customer Service 800.967.6696 | www.crateandbarrel.com
LOOP HUTCH
HARDWARE
Thank you for purchasing the Loop Hutch. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
14 - wood dowels
8 - bracket screws
1 - small screw
Missing hardware? Please call 800.606.6387 for replacements.
14 - cams
4 - shelf pins
1 - large screw
14 - cam screws
2 - brackets
14 - cam covers
1 - plastic anchor
1 - wall strap
TOOLS REQUIRED
phillips head screwdriver
1 - top panel
2 - side frames
(1 left, 1 right)
1 - adjustable shelf
1 - back panel
1 - fixed shelf
Made in China - r05 Page 1 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
LOOP HUTCH
left and right
A
side panels
B
back panel
NOTE: Make sure arrows on each cam points towards nearest edge with holes.
1 A) Insert 2 wood dowels, 5 cam screws and 2 cams into left and right side panels as shown. Make sure arrows on each cam points towards nearest edge with holes. Secure cam screws with a phillips head screwdriver. B) Insert 6 wood dowels and 6 cams into back panel as shown.
left side panel
back panel
2 Fit dowels of back panel into corresponding holes of left side panel as shown. With a screwdriver, turn cams clockwise until it securely engages each cam screw.
fixed shelf
3 Insert 4 cams and 4 wood dowels into fixed shelf as shown.
Made in China - r05 Page 2 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
4 Fit dowels of fixed shelf into corresponding holes of left side panel as shown. Secure 2 cams.
fixed shelf
LOOP HUTCH
top panel
right side panel
5 Fit dowels of assembled unit into corresponding holes of right side panel as shown. Secure 5 cams.
top panel
6 Insert 4 cam screws into underside of top panel as shown.
A
A
B
adjustable
shelf
7 With the assistance of another adult, carefully position unit upright as shown. Fit dowels of assembled unit into corresponding holes of top panel as shown. Secure 4 cams, and cover exposed cams with cam covers.
Made in China - r05 Page 3 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
8 A) Insert 4 shelf pins at desired shelf heights as shown. B) Place adjustable shelf into assembled unit. Make sure shelf is securely supported by shelf pins.
LOOP HUTCH
hutch
9 With the assistance of another adult, carefully place hutch onto file cabinet as shown. Attach 2
brackets to back of assembled unit with 4 bracket screws per bracket as shown. Secure
screws with a screwdriver. Assembly is now complete.
10 Safety Mounting Instructions A. Drill a hole in the wall slightly smaller than the diameter of the plastic wall anchor. Lightly tap with a hammer until the face is flush with the wall. B. Insert large screw through wall anchor strap and into the wall anchor. C. Insert small screw through wall anchor strap and into the top of unit. Mounting assembly is now complete.
small screw
file cabinet
WALL
wall strap
plastic anchor
large screw
NOTE: If you are unsure about your
NOTE: Insert screws 3/4"-1" from the edge of the strap
wall type or what mounting method you should use, consult a qualified professional or your local hardware store.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the wood is finished with a protective clear lacquer.
Made in China - r05 Page 4 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
Loading...