Customer Service 800-967-6696 | http://www.crateandbarrel.com
LATITUDE LARGE MEDIA STAND
Thank you for purchasing the Latitude Large
Media Stand. This page lists all the contents
included in the box. Please take time to identify
the hardware as well as the individual components
of this product. As you unpack and prepare for
assembly, place the contents on a carpeted or
padded area to protect them from damage.
Note: 2 people are required to safely assemble this
product.
COMPONENTS
1 - top panel
1 - bottom panel
(holes on bottom)
These holes
on both sides
2 - doors
(1 left, 1 right)
2 - side panels
(1 left, 1 right)
Made in Denmark - r09
2 - divider
panels
4 - legs
HARDWARE
36 - wood
dowels
36 - cam screws
4 - door
hinges
36 - cam covers2 - door stops
Missing hardware? Please call 800.606.6387 for replacements.
36 - cams
4 - door pull
bolts
4 - case
hinges
12 - wood screws
4 - leg bolts
12 - shelf pins
16 - hinge screws
TOOLS REQUIRED
Phillips head screwdriver
1 - middle back panel
2 - back panels
1 - base frame
1 - middle shelf
2 - side shelves
2 - door pull handles
4 - door pull standoffs
Page 1 of 5
Page 2
Customer Service 800-967-6696 | http://www.crateandbarrel.com
LATITUDE LARGE MEDIA STAND
1 Place 4 legs at each corner of the base frame, aligning
hole in leg with hole in bracket. Attach with 1 leg bolt per
leg, fully tightening with a phillips head screwdriver.
A
Top
Panel
B
Bottom
Panel
3 A. Insert 12 cam screws into the inner holes of the top panel. Secure, but do not over tighten with a screwdriver.
B. Insert 12 cam screws into the inner holes of the bottom panel and secure with a screwdriver.
Made in Denmark - r09
NOTE:
Do not over tighten the screws.
2 Position base frame assembly over holes in the bottom panel. Insert 12 wood screws through holes in frame and
into bottom panel and secure with a screwdriver.
Make sure arrow
on each cam
points to nearest
A
edge with
dowels
C
Side
Panel
D
B
4 A. Insert 6 wood dowels in the outer holes on the edge
of each side panel.
B. Insert 6 cams into each side panel, making sure arrow of
each cam points out towards nearest edge with dowels.
C. Fasten 2 cam screws at rear inner hole on each side
panel with a phillips head screwdriver.
D. Attach 2 case hinges to each side panel with 2 hinge screws. Use the top 2 holes for the top case hinge and the
bottom 2 holes for the bottom case hinge as shown.
Page 2 of 5
Page 3
Customer Service 800-967-6696 | http://www.crateandbarrel.com
LATITUDE LARGE MEDIA STAND
A
C
Back
Panel
Divider
Panel
D
B
5 A. Insert 4 wood dowels into the outer holes on edges
of each back panel.
B. Insert 4 cams into each back panel, making sure
arrows on cams points towards nearest edge.
C. Insert 6 wood dowels into outer holes on edge of
divider panels.
D. Insert 2 cam screws into the inner holes at the rear of
each divider panel.
7 A. Insert 4 wood dowels into the outer holes on the
edges of the middle back panel.
B. Fit middle back panel onto cam screws of each divider
panel. Secure all 4 cams with a phillips head screwdriver.
Made in Denmark - r09
Left
Side
Panel
6 Fit left side and divider panel onto back panel, aligning
cam screws and dowels with corresponding holes. Using a
phillips head screwdriver, turn all 4 cams on the back panel
clockwise until each cam tightly engages the cam screw.
Repeat for remaining right side, back and divider panel.
8 With the assistance of another adult, carefully lift each
back panel assembly and place into position on bottom
panel. Make sure dowels and cam screws on each panel are
aligned with their corresponding holes.
Back
Panel
Divider
Panel
Page 3 of 5
Page 4
Customer Service 800-967-6696 | http://www.crateandbarrel.com
LATITUDE LARGE MEDIA STAND
9 Using a phillips head screwdriver, turn each cam at
the base of the side panels clockwise until each cam
tightly engages the cam screw.
11 Fit 2 side shelves and 1 middle shelf into position.
Make sure each shelf is securely supported by the shelf
pins.
Made in Denmark - r09
Cam in
unlocked
position
Cam in
locked
position
10 Insert 12 shelf pins into the holes in the side and divider
panels at desired shelf heights.
A
B
12 A. With the assistance of another adult, fit cam screws
of the top panel into corresponding holes in the side and
divider panels. Secure all 12 cams by turning clockwise with
a screwdriver.
B. Adhere 2 door stops to the front edge of each shelf as
shown.
Page 4 of 5
Page 5
Customer Service 800-967-6696 | http://www.crateandbarrel.com
LATITUDE LARGE MEDIA STAND
13 A. Fit cup of 2 door hinges into large holes on both
door interiors. Secure each with 2 hinge screws per
hinge.
B. Attach 1 door pull handle to each door front with 2
pull standoffs and 2 pull screws as shown.
HINGE ADJUSTMENT
If the doors do not appear square or aligned, loosen or tighten the appropriate screws on each case hinge as illustrated.
A
1
1) Side to side adjustment:
Loosen screw A, adjust gap
with screw B and re-tighten
screw A.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not
Made in Denmark - r09
use furniture wax or polish as the wood is finished with a protective clear lacquer.
A
B
B
2) Depth adjustment:
Loosen screw A, push hinge arm
forwards or backwards, re-tighten
screw A and secure screw B with
a 1/4 turn clockwise.
A
B
14 A. Fit each door hinge onto the case hinge installed on
the side panels. Temporarily secure the set screw with a
screwdriver and refer to the instructions below for final
adjustment of the door and hinges.
B. Conceal all exposed cams with cam covers.
Assembly is now complete.
A
B
2
C
C
3
3) Height adjustment:
Loosen screw C, adjust
door height and retighten screw C.
Page 5 of 5
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.