
LANDON TWO DOOR CUPBOARD
ASSEMBLY HARDWARE
Thank you for purchasing the Landon Two Door Cupboard. This page lists all the contents included in the
box. Please take time to identify the hardware as well as
the individual components of this product. As you
unpack and prepare for assembly, place the contents on
a carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
8 - bolts
8 - wood
dowels
8 - hinge
screws
22 - back
screws
4 - door
hinges
8 - shelf
pins
WALL MOUNTING HARDWARE
1 - wall strap 1 - small
screw
Missing hardware? Please call 800.606.6387 for replacements.
1 - large
screw
1 - plastic
anchor
TOOLS REQUIRED
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
1 - top panel
1 - back panel
2 - adjustable
shelves
1 - bottom
2 - side panels
(1 left, 1 right)
Made in China - r04 Page 1 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
panel
2 - door frames
(1 left, 1 right)

LANDON TWO DOOR CUPBOARD
right side panel
NOTE: Do not over
tighten the bolts
left and right
side panels
1 Insert 4 wood dowels into left and right side panels
as shown.
bottom panel
left side panel
NOTE: Make sure front
edge of bottom panel is
positioned as shown
during assembly
2 Fit dowels of left and right side panels into corresponding holes of bottom panel as shown. Secure
each side panel with 2 bolts, using a phillips head
screwdriver. Do not over tighten the bolts.
NOTE: Do not over
tighten the screws
back
panel
3 With assistance of another adult, fit dowels of
assembly into corresponding holes of top panel.
Secure top panel with 4 bolts as shown.
Made in China - r04 Page 2 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
4 Attach back panel to assembly with 22 back
screws, using a screwdriver. With assistance of
another adult, position unit upright.

LANDON TWO DOOR CUPBOARD
A
A
B
adjustable shelf
5 A) Insert 8 shelf pins at desired shelf heights. Press
pins firmly to secure.
B) Place adjustable shelves onto shelf pins. Make sure
shelves are securely supported by each shelf pin.
left and right
door frames
6 Attach 2 door hinges to left and right door frames
with 2 hinge screws per hinge as shown, using a screwdriver.
pre-assembled
screws
panel
hinge
door
hinge
left door
frame
right door
frame
7 Fit door hinges over corresponding panel hinges of
assembly as shown. Using a screwdriver, secure each
hinge assembly with 2 pre-assembled screws.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth.
Do not use abrasive cleaners. Do not use
furniture wax or polish as the wood is finished
with a protective clear lacquer.
Assembly is now complete.
Made in China - r04 Page 3 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com

LANDON TWO DOOR CUPBOARD
OPTIONAL SAFETY MOUNTING INSTRUCTIONS
For added safety and stability, it is recommended that the wall
mounting hardware be installed. For safe mounting, it is essential
to use wall anchors appropriate to your wall type (i.e. plaster,
drywall, concrete, etc.). Mount to wood studs whenever possible.
A) Determine the final location of unit. Mark position on the wall,
approximately 2" below the top of unit as shown.
B) Drill a pilot hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in diameter
than the plastic anchor. Gently tap the plastic anchor until the
flange of the plastic anchor is flush with the wall.
C) Insert large screw through end of wall strap and through the
plastic anchor in the wall as shown.
D) Insert small screw through end wall strap and into the top
back of unit as shown.
Mounting assembly is now complete.
NOTE: If you are unsure about your wall type or what mounting
method you should use, consult a qualified professional or your
local hardware store.
SIDE VIEW DETAIL
wall strap
(NOTE: Insert screws
3/4"-1" from the
edge of the strap)
small
screw
large
screw
WALL
plastic
anchor
HINGE ADJUSTMENT
If the doors do not appear square or aligned,
loosen or tighten the appropriate screws on
each case hinge as illustrated.
1)
Side to side adjustment:
Loosen screw A, adjust gap
with screw B and re-tighten
screw A. A.
A
B
1
2) Depth adjustment:
Loosen screw A, push hinge arm
forwards or backwards, re-tighten
screw
2
3) Height adjustment:
Loosen screw C, adjust
door height and retighten screw C.
C
A
C
3
Made in China - r04 Page 4 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com