LANDON 54” MEDIA CONSOLE
ASSEMBLY HARDWARE
Thank you for purchasing the Landon 54” Media
Console. This page lists all the contents included in
the box. Please take time to identify the hardware as
well as the individual components of this product. As
you unpack and prepare for assembly, place the
contents on a carpeted or padded area to protect
them from damage.
Note: 2 people are required to safely assemble this
product.
COMPONENTS
10 - bolts 3 - large
12 - wood
dowels
screws
18 - back
screws
8 - shelf
pins
WALL MOUNTING HARDWARE
1 - wall strap 1 - small
screw
Missing hardware? Please call 800.606.6387 for replacements.
1 - large
screw
1 - plastic
anchor
TOOLS REQUIRED
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
1 - top panel 1 - back panel1 - bottom panel
2 - side panels
(1 left, 1 right)
Made in China - r03 Page 1 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
1 - partition
2 - door fronts
(1 left, 1 right)
2 - adjustable shelves
LANDON 54” MEDIA CONSOLE
A
left and right
side panels
partition
B
bottom panel
C
1 A) Insert 2 wood dowels into left and right side
panels as shown.
B) Insert 4 wood dowels into partition as shown.
C) A) Insert 4 wood dowels into bottom panel as
shown.
right side panel
bottom panel
NOTE: Make sure front
edge of bottom panel is
positioned as shown
during assembly
NOTE: Do not over
tighten the bolts
left side panel
2 Fit dowels of bottom panel into corresponding holes
of left and right side panels as shown. Secure each
side panel with 2 bolts, using a phillips head screw-
driver. Do not over tighten the bolts.
partition
3 Fit dowels of partition into corresponding holes of
bottom panel. Secure partition with 3 large screws as
shown, using a screwdriver. Do not over tigthen the
screws.
4 With assistance of another adult, fit dowels of
assembly into corresponding holes of top panel.
Secure top panel with 6 bolts as shown.
Made in China - r03 Page 2 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
LANDON 54” MEDIA CONSOLE
back
panel
A
REAR
FRONT
B
adjustable shelf
A
NOTE: Locate FRONT and
REAR labels on the bottom
of each adjustable shelf.
During assembly, make sure
to insert each shelf as shown.
5 Attach back panel to assembly with 18 back
screws, using a screwdriver. With assistance of
another adult, position unit upright.
left
door front
BACK DETAIL
OF DOOR FRONT
pin
6 A) Insert 8 shelf pins at desired shelf heights. Press
pins firmly to secure.
B) Place adjustable shelves onto shelf pins. Make sure
shelves are securely supported each shelf pin.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth.
Do not use abrasive cleaners. Do not use
furniture wax or polish as the wood is finished
with a protective clear lacquer.
right door
front
7 Insert bottom wheels of right door front into bottom
back groove of unit as shown. Press and hold down both
pins (located at the top of door) and insert top edge of door
into top back groove of unit. Release pins to secure door.
Repeat for left door front using the front groove of unit.
Assembly is now complete.
Made in China - r03 Page 3 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
LANDON 54” MEDIA CONSOLE
OPTIONAL SAFETY MOUNTING INSTRUCTIONS
For added safety and stability, it is recommended that the wall
mounting hardware be installed. For safe mounting, it is essential
to use wall anchors appropriate to your wall type (i.e. plaster,
drywall, concrete, etc.). Mount to wood studs whenever possible.
A) Determine the final location of unit. Mark position on the wall,
approximately 2" below the top of unit as shown.
B) Drill a pilot hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in diameter
than the plastic anchor. Gently tap the plastic anchor until the
flange of the plastic anchor is flush with the wall.
C) Insert large screw through end of wall strap and through the
plastic anchor in the wall as shown.
D) Insert small screw through end wall strap and into the top
back of unit as shown.
Mounting assembly is now complete.
NOTE: If you are unsure about your wall type or what mounting
method you should use, consult a qualified professional or your
local hardware store.
SIDE VIEW DETAIL
wall strap
(NOTE: Insert screws
3/4"-1" from the
edge of the strap)
small
screw
large
screw
WALL
plastic
anchor
Made in China - r03 Page 4 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...