Thank you for purchasing the Kingston Two Door
Cupboard. This page lists all the contents included in
the box. Please take time to identify the hardware as well
as the individual components of this product. As you
unpack and prepare for assembly, place the contents on
a carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
ASSEMBLY HARDWARE
6 - cams6- cam
screws
2- pulls4 - pull
screws
16 - bolts16- spring
20 - small
screws
Missing hardware? Please call
800.606.6387 for replacements.
WALL MOUNTING HARDWARE
4 - medium
screws
4 - large
screws
2 - wall
straps
TOOLS REQUIRED
Phillips head screwdriver
washers
10- shelf
pins
4 - wall
brackets
16- flat
washers
4 - plastic
anchors
COMPONENTS
1 - front frame
1 - top panel1 - bottom panel
2 - adjustable shelves
1 - back panel
2 - side panels
(1 - left, 1- right)
Make sure arrows
on each cam point
towards nearest edge
with holes.
B
A
1 A) Insert 2 cam screws into left side panel as
shown. Secure with a Phillips head screwdriver,
but do not over tighten cam screws. Repeat step for
right side panel.
B) Insert 4 cams into holes located on bottom panel.
Make sure arrows on each cam point towards nearest
edge with holes.
Made in Vietnam - r09Customer Service 800.967.6696 | Latest instructions available on www.crateandbarrel.com
Page 1 of 4
KINGSTON TWO DOOR CUPBOARD
A
2 A) Fit left and right side panels onto bottom
panel by aligning cam screws with corresponding holes. Secure cams using a Phillips head
screwdriver. Turn cams clockwise until it securely
engages each cam screw.
B) Insert 2 cams in holes located on bottom panel.
Make sure arrows on each cam point towards nearest
edge with holes.
B
A
3 Insert 2 cam screws into front frame as shown.
Secure with Phillips head screwdriver.
B
B
VIEW FROM BELOW
4 A) With assistance of another adult, carefully fit
front frame onto assembled unit by aligning cam
screws with corresponding holes. Secure cams
using a Phillips head screwdriver. Turn cams
clockwise until it securely engages each cam screw.
B) Secure front frame with 8 bolts, 8 spring
washers, and 8 flat washers using a Phillips head
screwdriver.
Made in Vietnam - r09Customer Service 800.967.6696 | Latest instructions available on www.crateandbarrel.com
5 With assistance of another adult, carefully position
unit upright. Fit top panel onto assembled unit by
aligning dowels with corresponding holes. Secure
top panel with 8 bolts, 8 spring washers, and 8 flat
washers using a Phillips head screwdriver.
Page 2 of 4
KINGSTON TWO DOOR CUPBOARD
6 Attach back panel onto assembled unit as shown,
with 20 small screws. Secure with a Phillips head
screwdriver, but do not over tighten screws.
A
A
B
7 A) Insert 8 shelf pins into assembled unit at
desired shelf levels as shown. Press firmly to secure.
B) Fit 2 adjustable shelves into assembled unit, and
place onto shelf pins. Make sure each shelf is
securely supported by the shelf pins.
B
Back of
front frame
8 Lift adjustable shelf slightly to insert 1 shelf pin
into back of front frame at desired shelf level as
shown. Press shelf pin firmly to secure. Lay shelf
onto shelf pin. Repeat step for additional adjustable
shelf.
9 Attach pull onto assembled unit as shown, with 2
pull screws. Secure with a Phillips head
screwdriver. Repeat step for additional pull.
Assembly is now complete.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as the
wood is finished with a protective clear lacquer.
Made in Vietnam - r09Customer Service 800.967.6696 | Latest instructions available on www.crateandbarrel.com
Page 3 of 4
KINGSTON
wall
F
strap
wall
bracket
TWO DOOR CUPBOARD
plastic
C
anchor
wall
bracket
large
D
screw
medium
A
screw
10 Safety Mounting Instructions
For added safety and stability, it is recommended that the
wall mounting hardware be installed. For safe mounting, it
is essential to use wall anchors appropriate to your wall type
(i.e. plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
A) Attach wall bracket to top of unit using 2 medium screws as shown.
B) Determine the final location of unit. Mark position on the
wall, approximately 2" below the wall bracket mounted to
the back of the unit.
C) Drill a hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in
diameter than the anchor. Gently tap the plastic anchor
until the flange of the anchor is flush with the wall.
D) Attach wall bracket to the wall by inserting 2 large screws, and into the plastic anchor in the wall.
E) Place the unit so the wall brackets on the back edge are
aligned with the wall brackets on the wall.
F) Lace one end of the wall strap through both brackets,
and into the other end of the strap.
G) Pull the strap tightly until secure.
H) Repeat steps A-G for remaining wall brackets and wall
straps.
NOTE:
If you are unsure about your wall type or what
mounting method you should use, consult a
qualified professional or your local hardware
store.
Made in Vietnam - r09Customer Service 800.967.6696 | Latest instructions available on www.crateandbarrel.com
Page 4 of 4
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.