Page 1
KINGSTON TALL CABINET
ASSEMBLY HARDWARE
Thank you for purchasing the Kingston Tall Cabinet.
This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
4 - cams 4- cam
screws
1- pull 2 - pull
screws
18 - bolts 18- spring
washers
19 - small
screws
8- shelf
pins
18- flat
washers
WALL MOUNTING HARDWARE
4 - medium
screws
Missing hardware? Please call 800.606.6387 for replacements.
4 - large
screws
2 - wall
straps
4 - wall
brackets
4 - plastic
anchors
TOOLS REQUIRED
phillips head screwdriver
1 - top panel
1 - front frame
Made in Vietnam - r05 Customer Service 800.967.6696 | Latest instructions available on www.crateandbarrel.com
1 - back panel
1 - left
side panel
2 - adjustable shelves
1 - right
side panel
1 - bottom panel
1 - fixed shelf
Page 1 of 4
Page 2
KINGSTON TALL CABINET
A
B
1 A) Insert 2 cam screws into left panel as shown.
Secure with a Phillips head screwdriver, but do not
over tighten cam screws. Repeat step for right
panel.
B) Insert 4 cams into holes located on bottom panel.
Make sure arrows on each cam point towards nearest
edge with holes.
Make sure arrows
on each cam point
towards nearest edge
with holes.
A
B
2 A) Attach left and right side panels onto bottom
panel and fixed shelf by aligning cam screws with
corresponding holes. Secure fixed shelf as shown
with 4 bolts, 4 spring washers, and 4 flat washers
using a Phillips head screwdriver.
B) Secure cams using a Phillips head screwdriver.
Turn each cam clockwise until it securely engages
each cam screw.
VIEW FROM BELOW
3 With assistance of another adult, carefully fit front
frame onto assembled unit by aligning dowels with
corresponding holes as shown. Secure front frame
with 8 bolts, 8 spring washers, and 8 flat washers
using a Phillips head screwdriver.
A
A
B
4 A) With assistance of another adult, carefully
place unit upright. Fit top panel onto assembled unit
by aligning dowels with corresponding holes. Secure
top panel with 6 bolts, 6 spring washers, and 6 flat
washers using a Phillips head screwdriver.
B) Attach pull onto front frame as shown with 2 pull
screws. Secure with Phillips head screwdriver.
Made in Vietnam - r05 Customer Service 800.967.6696 | Latest instructions available on www.crateandbarrel.com
Page 2 of 4
Page 3
KINGSTON TALL CABINET
5 Attach back panel onto assembled unit as shown,
with 19 small screws. Secure with a Phillips head
screwdriver, but do not over tighten the screws.
A
B
6 A) Insert 8 shelf pins into assembled unit at
desired shelf levels. Press firmly to secure.
B) Fit adjustable shelf into assembled unit, and
place on shelf pins. Make sure shelf is securely
supported by the shelf pins. Repeat step for
additonal shelf. Assembly is now complete.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as the
wood is finished with a protective clear lacquer.
Made in Vietnam - r05 Customer Service 800.967.6696 | Latest instructions available on www.crateandbarrel.com
Page 3 of 4
Page 4
KINGSTON
wall
F
strap
wall
bracket
TALL CABINET
plastic
C
anchor
bracket
D
medium
A
screw
wall
large
screw
7 Safety Mounting Instructions
For added safety and stability, it is recommended that the
wall mounting hardware be installed. For safe mounting, it
is essential to use wall anchors appropriate to your wall type
(i.e. plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
A) Attach wall bracket to top of unit using 2 medium
screws as shown.
B) Determine the final location of unit. Mark position on the
wall, approximately 2" below the wall bracket mounted to
the back of the unit.
C) Drill a hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in
diameter than the anchor. Gently tap the plastic anchor
until the flange of the anchor is flush with the wall.
D) Attach wall bracket to the wall by inserting 2 large
screws, and into the plastic anchor in the wall.
E) Place the unit so the wall brackets on the back edge are
aligned with the wall brackets on the wall.
F) Lace one end of the wall strap through both brackets,
and into the other end of the strap.
G) Pull the strap tightly until secure.
H) Repeat steps A-G for remaining wall brackets and wall
straps.
NOTE:
If you are unsure about your wall type or what
mounting method you should use, consult a
qualified professional or your local hardware
store.
Made in Vietnam - r05 Page 4 of 4
Customer Service 800.967.6696 | Latest instructions available on www.crateandbarrel.com
Loading...