Page 1
KINGSTON 52” MEDIA STAND
HARDWARE
Thank you for purchasing the Kingston 52” Media
Stand. This page lists all the contents included in the
box. Please take time to identify the hardware as well as
the individual components of this product. As you
unpack and prepare for assembly, place the contents on
a carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
4 - cams 4- cam
screws
8 - flat
washers
Missing hardware? Please call 800.606.6387 for replacements.
8 - spring
washers
8 - bolts 2 - large
screws
20 - screws
16- shelf
pins
TOOLS REQUIRED
Phillips head screwdriver
1 - top panel
1 - bottom panel
Made in China - r06 Page 1 of 3
Customer Service 800.967.6696 | Latest instructions available on www.crateandbarrel.com
1 - back panel
1 - middle
partition
4 - adjustable
shelves
1 - left side
panel
1 - left sliding
door panel
1 - right side
panel
1 - center
support
1 - right sliding
door panel
Page 2
KINGSTON 52” MEDIA STAND
A
B
Make sure arrows
on each cam point
towards nearest edge
with holes.
1 A) Insert 2 cam screws into left side panel as
shown. Secure with a Phillips head screwdriver,
but do not over tighten cam screws. Repeat step for
right side panel.
B) Insert 4 cams into holes located on bottom panel.
Make sure arrows on each cam point towards nearest
edge with holes.
B
B
A
NOTE: Do not over
tighten the screws.
2 A) Attach middle partition and bottom panel by
aligning holes with pre-assembled dowels. Secure
middle partition with 2 large screws using a Phillips
head screwdriver. Do not over tighten the screws.
B) Attach center support onto bottom panel by
aligning holes with pre-assemble dowels. Secure
center support with 2 bolts, 2 spring washers, and
2 flat washers using a Phillips head screwdriver.
B
A
3 A) Carefully fit left and right side panels onto
assembled unit by aligning cam screws and dowels
with corresponding holes.
B) Secure cams using a Phillips head screwdriver.
Turn clockwise until each cam securely engages each
cam screw.
Made in China - r06 Page 2 of 3
Customer Service 800.967.6696 | Latest instructions available on www.crateandbarrel.com
4 Attach top panel onto assembled unit by aligning
holes with pre-assembled dowels. Secure left side
panel, right side panel, and middle partition with 6
bolts, 6 spring washers, and 6 flat washers using a
Phillips head screwdriver.
Page 3
KINGSTON 52” MEDIA STAND
A
A
B
6 Attach back panel onto assembled unit as shown,
with 20 screws. Secure with a Phillips head
screwdriver.
8 Fit the bottom rollers of the right sliding door
panel into back groove. Depress levers located at
the top of the door, tilt the door into the groove in the
top panel. Release the levers to secure door. Repeat
steps for left sliding door panel.
Assembly is now complete.
7 A) Insert 16 shelf pins into assembled unit at
desired shelf levels. Press firmly to secure.
B) Place 4 adjustable shelves into assembled unit.
ADJUSTING THE LEVELERS
If the doors do not appear square or aligned,
try adjusting the levelers on the bottom of
each leg.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as the
wood is finished with a protective clear lacquer.
Made in China - r06 Page 3 of 3
Customer Service 800.967.6696 | Latest instructions available on www.crateandbarrel.com
Page 4
KINGSTON MEDIA TOWER
ASSEMBLY HARDWARE
Thank you for purchasing the Kingston Media Tower.
This page
Please take the time to identify the hardware as well as
the individual components
unpack and prepare for assembly, place the contents
on a carpeted or padded area to protect them from
damage.
Note: 2 people are required to safely assemble this product.
lists all the contents included in the box.
to this product. As you
COMPONENTS
6 - cam
screws
16 - flat
washers
6 - cams 20 - small
screws
16 - spring
washers
16 - large
bolts
1 - pull 12 - shelf
2 - small
bolts
pins
WALL MOUNTING HARDWARE
4 - medium
screws
Missing hardware? Please call 800.606.6387 for replacements.
4 - large
screws
2 - wall
straps
4 - wall
brackets
4 - plastic
anchors
TOOLS REQUIRED
phillips head screwdriver
1 - top panel
1 - -fixed shelf
2 - side panels
(1 left, 1 right)
1 - bottom
panel
Made in China - r05 Page 1 of 4
1 - front frame 1 - back panel
2 - top adjustable
shelves
1 - bottom
adjustable
shelf
Page 5
KINGSTON
MEDIA TOWER
B
flat washer
spring washer
large bolt
right/left
A
side panels
bottom
B
panel
NOTE: Make sure
arrows on each
cam points towards
nearest edge with
holes.
1 A) Insert 2 cam screws into right/left side panels as
shown. Secure cam screws with a phillips head
screwdriver.
B) Insert 6 cams into bottom panel as shown. Make sure
arrows on each cam points toward nearest edge with holes.
A
fixed
shelf
B
A
bottom
panel
2 A) Fit dowels of fixed shelf and bottom panel into
corresponding holes of right/left side panel as shown.
Secure all cams with a screwdriver. Make sure cams securely
engage each cam screw.
B) Secure fixed shelf with 4 large bolts, 4 spring washers,
and 4 flat washers as shown. Fasten bolts with a
screwdriver.
front
frame
3 Insert 2 cam screws into front frame as shown.
B
B
A
4 A) Fit dowels of assembled unit into corresponding holes
of front frame as shown. Secure 2 cams on bottom panel
with a screwdriver.
B) Secure front frame with 6 large bolts, 6 spring
washers, and 6 flat washers as shown.
front
frame
Made in China - r05 Page 2 of 4
Page 6
KINGSTON
top
panel
MEDIA TOWER
back
panel
5 Fit dowels of assembled unit with corresponding holes
of top panel as shown. Secure top panel with 6 large
bolts, 6 spring washers, and 6 flat washers as shown.
A
A
B
top
adjustable
shelves
C
bottom
adjustable
shelf
C
6 Attach back panel to assembled unit with 20 small
screws as shown. Secure screws with screwdriver.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth.
Do not use abrasive cleaners. Do not use
furniture wax or polish as the wood is finished
with a protective clear lacquer.
7 A) Insert 12 shelf pins at desired shelf heights as shown.
B) Place top/bottom adjustable shelves into assembled
unit as shown. Make sure each shelf is securely supported
by shelf pins.
C) Attach pull to door with 2 small bolts. Secure bolts with
screwdriver.
Assembly is now complete.
Made in China - r05 Page 3 of 4
Page 7
KINGSTON
wall
F
strap
wall
bracket
MEDIA TOWER
plastic
C
anchor
wall
bracket
large
D
screw
medium
A
screw
7 Safety Mounting Instructions
For added safety and stability, it is recommended that the
wall mounting hardware be installed. For safe mounting, it
is essential to use wall anchors appropriate to your wall type
(i.e. plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
A) Attach wall bracket to top of bookcase using 2 medium
screws as shown.
B) Determine the final location of bookcase. Mark position
on the wall, approximately 2" below the wall bracket
mounted to the back of the cabinet.
C) Drill a hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in
diameter than the anchor. Gently tap the plastic anchor
until the flange of the anchor is flush with the wall.
D) Attach wall bracket to the wall by inserting 2 large
screws, and into the plastic anchor in the wall.
E) Place the unit so the wall brackets on the back edge are
aligned with the wall brackets on the wall.
F) Lace one end of the wall strap through both brackets,
and into the other end of the strap.
G) Pull the strap tightly until secure.
H) Repeat steps A-G for remaining wall brackets and wall
straps.
NOTE:
If you are unsure about your wall type or what
mounting method you should use, consult a
qualified professional or your local hardware
store.
Made in China - r05 Page 4 of 4
Loading...