
KENTON DOUBLE CUBE WITH TWO DOORS
HARDWARE
Thank you for purchasing the Kenton
Double Cube with Two Doors. This page
lists all the contents included in the box.
Please take time to identify the hardware as
well as the individual components of this
product. As you unpack and prepare for
assembly, place the contents on a carpeted
or padded area to protect them from
damage.
COMPONENTS
12 - cams
12 - cam
covers
4 - door bumpers
Missing hardware? Please call 800.606.6387 for replacements.
12 - cam
screws
2 - pulls
12 - wood
dowels
4 - bolts 16 - screws
4 - hinges
TOOLS REQUIRED
Phillips head screwdriver
2 - end panels
(1 labeled top, 1 labeled bottom)
2 - side panels
(left labeled L, right
labeled R)
1 - back panel
Made in China - r03
Side Panel
A
1 - middle
panel
2 - doors
Customer Service 800.967.6696 | www.crateandbarrel.com
B
1 A. Insert 4 wood dowels into the outer holes on the
edges of the 2 side panels and 1 middle panel.
B. Insert 4 cams into the large holes in each side panel
and middle panel. Make sure arrow on each cam points
out towards edge with dowels.
Side Panel
Middle
Panel
Make sure arrow on
each cam points towards
edge with dowels
B
Middle
Panel
Page 1 of 3

KENTON DOUBLE CUBE WITH TWO DOORS
A
3 A. Place side panels and middle panel into position as
shown, making sure slots on side panels line up with slot on
2 Insert 4 cam screws into inner holes of the 2 end
panels as shown. Secure each screw with a phillips
head screwdriver, but do not over tighten.
bottom panel. Align dowels and cam screws and firmly
press into position.
B. Slide back panel into the corresponding slot in the
bottom & side panels.
B
Cam in
unlocked
position
4 Using a phillips head screwdriver, turn each cam at the
base of the side and middle panels clockwise until each
cam tightly engages each cam screw.
Made in China - r03
Customer Service 800.967.6696 | www.crateandbarrel.com
Cam in
locked
position
5 Repeat Steps 3 and 4 for attachment of the top panel.
Be sure that back panel is seated in the slot at the back
of the top panel before securing the 4 cams.
Page 2 of 3

KENTON DOUBLE CUBE WITH TWO DOORS
A
C
B
7 A) Align holes in hinges with holes in side panels and
6 A) Attach 2 hinges to each door with 2 screws per
hinge. Secure, but do not over tighten each screw with a
phillips head screwdriver.
B) Attach door pull to each door front with 2 bolts.
C) Adhere 2 door bumpers to each door interior as shown.
attach with 2 screws per hinge. Do not over tighten the
screws. If necessary, adjust the hinges to align the doors
(refer to the directions below).
B) Conceal all exposed cams with cam covers.
Assembly is now complete.
A
B
HINGE ADJUSTMENT
If the doors do not appear square or aligned, loosen or tighten the appropriate screws on each case hinge as illustrated.
A
B
A
C
B
C
1
1) Side to side adjustment:
Loosen screw A, adjust gap
with screw B and re-tighten
screw A.
CLEANING AND CARE
2
2) Depth adjustment:
Loosen screw A, push hinge arm
forwards or backwards, re-tighten
screw A and secure screw B with
a 1/4 turn clockwise.
3
3) Height adjustment:
Loosen screw C, adjust
door height and retighten screw C.
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or
polish as the wood is finished with a protective clear lacquer.
Made in China - r03
Customer Service 800.967.6696 | www.crateandbarrel.com
Page 3 of 3