
KENDEL 44” TWO DRAWER CASE
ASSEMBLY HARDWARE
Thank you for purchasing the Kendel 44” Two Drawer
Case. This page lists all the contents included in the
box. Please take time to identify the hardware as well
as the individual components of this product. As you
unpack and prepare for assembly, place the contents
on a carpeted or padded area to protect them from
damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
8 - small
screws
2 - connecting
brackets
MOUNTING HARDWARE
2 - wall
straps
Missing hardware? Please call 800.606.6387 for replacements.
4 - brackets 4 - plastic
4 - medium
screws
4 - large
screws
anchors
TOOLS REQUIRED
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
METHOD TO REMOVE
THE DRAWERS
DRAWER STOP SIDE VIEW
drawer
stop
locked
position
1 - two drawer
assembly
1 Carefully remove drawers from assembled unit. Open
drawer and locate drawer stop on back of drawer assembly. Push down on tab and slide drawer assembly out as
shown. Repeat step for remaining drawer assembly.
Made in Vietnam - r04 Page 1 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
unlocked
position

KENDEL 44” TWO DRAWER CASE
CLEANING & CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as
the unit is finished with a protective clear lacquer. It is
recommended to use coasters to protect surface from
heat and water.
MULTIPLY UNIT ASSEMBLY
22”
22”
2 If you purchased multiple Kendel
items, it is suggested that every 22”
and 44” unit be secured together as
shown, connecting every 22” and
44” unit with 2 connecting plates.
Attach each plate with 4 small
crews using a screwdriver.
Repeat steps for each additional
item.
22”
22” 44”
44”
44”
Made in Vietnam - r04 Page 2 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com

KENDEL
44” TWO DRAWER CASE
WALL MOUNTING ASSEMBLY FOR MULTIPLE UNITS
bracket
large
D
screw
C
A
plastic
anchor
medium
screw
F
wall
strap
bracket
NOTE:
If you are unsure about your wall type or
what mounting method you should use,
consult a qualified professional or your
local hardware store.
4 Safety Mounting Instructions
For added safety and stability, it is recommended that the
wall mounting hardware be installed. For safe mounting, it is
essential to use wall anchors appropriate to your wall type
(i.e. plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
A) Locate pilot holes on back of unit, and attach 1 bracket
using 2 medium screws as shown.
B) Determine the final location of unit. Mark position on the
wall, approximately 2" below the wall bracket mounted to the
back of the unit.
C) Drill a hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in
diameter than the plastic anchor. Gently tap the plastic
anchor until the flange of the anchor is flush with the wall.
D) Attach 1 bracket to the wall by inserting 2 large screws
trough the bracket and into the plastic anchors in the wall.
E) Place the unit so the wall brackets on the back edge are
aligned with the wall brackets on the wall.
F) Lace one end of the wall strap through both brackets,
and into the other end of the strap.
G) Pull the strap tightly until secure.
H) Repeat steps A-G for remaining wall brackets and wall
straps.
Made in Vietnam - r04 Page 3 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com