Page 1
KENDEL 44” SLIDING DOOR BOOKCASE
ASSEMBLY HARDWARE
Thank you for purchasing the Kendel 44” Sliding Door
Bookcase. This page lists all the contents included in
the box. Please take time to identify the hardware as
well as the individual components of this product. As
you unpack and prepare for assembly, place the
contents on a carpeted or padded area to protect them
from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
8 - flat
washers
8 - spring
washers
pins
2 - connecting
brackets
22 - small
screws
8 - bolts8 - shelf
MOUNTING HARDWARE
2 - wall
straps
Missing hardware? Please call 800.606.6387 for replacements.
4 - brackets 4 - plastic
4 - medium
screws
4 - large
screws
anchors
TOOLS REQUIRED
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
(1- left, 1- right)
1 - center panel
2 - door panels
(1- left, 1- right)
1 - wire
management
cover
1 - back panel2 - side panels
1 - bottom panel1 - top panel2 - adjustable shelves
Made in Vietnam - r05 Page 1 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 2
KENDEL 44” SLIDING DOOR BOOKCASE
right side
panel
A
NOTE: Do not over
tighten the bolts
bottom
panel
NOTE: Make sure apron of
bottom panel is facing the
front as shown
A
1 A) Fit dowels of bottom panel into corresponding
holes of left/right side panels, and fasten with 2 bolts, 2
spring washers and 2 flat washers per panel as shown.
Secure, but do not over tighten, bolts with a phillips
head screwdriver.
B) Fit dowels of center panel into corresponding holes in
the bottom panel as shown.
left side
panel
top
panel
B
center
panel
2 With the assistance of another adult, position unit upright.
Fit dowels of assembled unit into corresponding holes of top
panel, and fasten with 4 bolts, 4 spring washers and 4 flat
washers as shown.
NOTE: Do not over
B
tighten the screws
back
panel
A
wire managment
cover
3 A) Insert wire managment cover into
corresponding window of back panel as shown.
B) Attach back panel with 14 small screws using a
screwdriver as shown. Do not over tighten screws.
A
A
adjustable
B
shelves
4 A) Insert 8 shelf pins into holes at the desired shelf
height.
B) Tilt adjustable shelves and place into assembled unit
as shown. Make sure shelves are securely supported by
shelf pins.
Made in Vietnam - r05 Page 2 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 3
KENDEL
left door
44” SLIDING DOOR BOOKCASE
right door
MULTIPLY UNIT ASSEMBLY
5 Insert cleat on top edge of left door into top
back groove of unit as shown. At this point, insert
wheels on bottom edge of door into bottom back
groove of unit. Repeat for right door using the
front groove of unit.
Assembly is now complete.
22”
22”
22”
44”
22” 44”
6 If you purchased multiple Kendel Bookcases, it is suggested that
every 22” and 44” bookcase be secured together as shown,
connecting every 22” and 44” bookcase with 2 connecting plates.
Attach each plate with 4 small screws using a screwdriver. Repeat
steps for each additional bookcase.
22”
bookcase
(sold
seperately)
22”
bookcase
(sold
seperately)
44”
Made in Vietnam - r05
44”
bookcase
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 3 of 4
Page 4
KENDEL
44” SLIDING DOOR BOOKCASE
WALL MOUNTING ASSEMBLY FOR MULTIPLE UNITS
plastic
C
anchor
bracket
large
D
screw
medium
A
screw
5 Safety Mounting Instructions
F
wall
strap
bracket
NOTE:
If you are unsure about your wall type or what
mounting method you should use, consult a
qualified professional or your local hardware
store.
For added safety and stability, it is recommended that the wall
mounting hardware be installed. For safe mounting, it is
essential to use wall anchors appropriate to your wall type (i.e.
plaster, drywall, concrete, etc.). Mount to wood studs whenever
possible.
A) Locate pilot holes on back of unit and attach 1 bracket to
unit using 2 medium screws as shown.
B) Determine the final location of unit. Mark position on the
wall, approximately 2" below the wall bracket mounted to the
back of the unit.
C) Drill a hole in the wall stud. If the wall stud is not available,
drill a hole in the wall that is slightly smaller in diameter than the
plastic anchor. Gently tap the plastic anchor until the flange of
the anchor is flush with the wall.
D) Attach 1 bracket to the wall by inserting 2 large screws
through the bracket and into the plastic anchors in the wall.
E) Place the unit so the wall brackets on the back edge are
aligned with the wall brackets on the wall.
F) Lace one end of the wall strap through both brackets, and
into the other end of the strap.
G) Pull the strap tightly until secure.
H) Repeat steps A-G for remaining wall brackets and wall
straps.
CLEANING & CARE
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as
the unit is finished with a protective clear lacquer. It is recommended to use coasters to protect surface from heat
and water.
Made in Vietnam- r05 Page 4 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...