HUXLEY LARGE SIDEBOARD
ASSEMBLY HARDWARE
Thank you for purchasing the Huxley Large Sideboard.
This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
16 - wood
dowels
3 - drawer
pull bolts
30 - large
screws
4 - hinges
28 - medium
screws
8 - shelf
pins
8 - small
screws
4 - magnets
12 - large
bolts
8 - magnet
screws
2 - door
pull bolts
5 - pulls
WALL MOUNTING HARDWARE
1 - wall strap 1 - small
screw
Missing hardware? Please call 800.606.6387 for replacements.
1 - large
screw
1 - plastic
anchor
TOOLS REQUIRED
(We recommend the use of hand tools instead of power tools)
phillips head screwdriver
1 - top
panel
2 - side panels
(1 left, 1 right)
2 - partitions
(1 left, 1 right)
2 - door fronts
(1 left, 1 right)
1 - bottom
panel
2 - adjustable
shelves
2 - top
drawer sides
Made in China - r10 Page 1 of 5
1 - top
drawer front
4 - bottom
drawer sides
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
2 - bottom
drawer fronts
1 - top
drawer bottom
1 - top
drawer back
2 - bottom
drawer bottoms
2 - bottom
drawer backs
1 - back panel
HUXLEY LARGE SIDEBOARD
left and right
A
side panels
bottom panel
C
left and right
B
partitions
1 A) Insert 2 wood dowels into left and right side panels
as shown.
B) Insert 4 wood dowels into left and right partitions as
shown.
C) Insert 4 wood dowels into bottom panel as shown.
NOTE: Make sure front
edge of bottom panel is
positioned as shown
bottom
panel
NOTE: Do not over
tighten the bolts
right side
panel
left side
panel
2 With the assitance of another adult, fit dowels of
bottom panel into corresponding holes of left and right
side panels as shown. Secure bottom panel to left and
right side panels with 4 large bolts as shown, using a
phillips head screwdriver. Do not over tighten the bolts.
NOTE: Make sure glides of
partitions are facing inside
as shown
left partition
right partition
NOTE: Do not over
tighten the screws
3 Fit dowels of left and right partition into corresponding holes of bottom panel as shown. Secure
left and right partition to bottom panel with 6 large
screws as shown, using a phillips head screwdriver.
Do not over tighten the screws.
top
panel
NOTE: Do not over
tighten the bolts
4 With the assistance of another adult, position assembled
unit upright as shown. Fit dowels of left/right side panels
and left/right partitions into corresponding holes of top
panel as shown. Secure top panel with 8 large bolts as
shown, using screwdriver.
Made in China - r10 Page 2 of 5
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
HUXLEY LARGE SIDEBOARD
NOTE: Do not over
tighten the screws
back panel
5 Attach back panel to assembled unit with 28 medium
screws as shown. Secure, but do not over tighten the
screws, using a screwdriver.
B
top drawer
side
top drawer
front
A
top
drawer bottom
top drawer
back
top drawer
side
6 A) Slide top drawer bottom into corresponding grooves
of top drawer front and back as shown.
B) Attach top drawer sides to assembled unit with 4 large
screws per side as shown, using a screwdriver.
Repeat steps for bottom drawer assemblies.
shelf pin
A
adjustable
B
shelf
C
7 A) Insert 8 shelf pins at desired shelf heights. Press
shelf pins firmly to secure.
B) Place 2 adjustable shelves onto shelf pins as shown.
Make sure shelves are securely supported by each shelf
pin.
C) Attach 4 magnets to top and bottom panels as
shown. Secure each magnet with 2 magnet screws,
using a screwdriver.
A
adjustable
B
shelf
left door
right door
8 Attach 2 door hinges to left and right doors with 2 small
screws per hinge as shown, using a screwdriver.
Made in China - r10 Page 3 of 5
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
HUXLEY LARGE SIDEBOARD
pull
left and right
door front
drawer
assemblies
9 A) Attach 1 pull to each drawer assembly with 1
drawer pull bolt as shown.
B) Attach 1 pull to each door with 1 door pull bolt as
shown.
NOTE: If doors are not
aligned, refer to the Hinge
Adjustment diagram at the
end of these instructions
left
door
right
door
top
drawer
assembly
bottom drawer
assembly
bottom drawer
assembly
10 Insert top and bottom drawer assemblies into
assembled unit as shown. Push drawers back until you
hear a click.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do
not use abrasive cleaners. Do not use furniture wax
pre-installed
screw
11 Attach 2 door hinges of left and right doors to
corresponding 2 mounting plates of left and right side
panels as shown. Secure hinges with pre-installed
screw using a screwdriver.
Assembly is now complete.
Made in China - r10 Page 4 of 5
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
or polish as the wood is finished with a protective
clear lacquer.
HUXLEY
LARGE SIDEBOARD
OPTIONAL SAFETY MOUNTING INSTRUCTIONS
For added safety and stability, it is recommended that the wall
mounting hardware be installed. For safe mounting, it is
essential to use wall anchors appropriate to your wall type (i.e.
plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
A) Determine the final location of unit. Mark position on the wall,
approximately 2” below the top of the unit as shown.
B) Drill a pilot hole in the wall stud. If a wall stud is not available,
drill a hole in the wall that is slightly smaller in diameter than the
plastic anchor. Gently tap the plastic anchor until the flange of
the plastic anchor is flush with the wall.
C) Insert 1 large screw through end of wall strap and through
plastic anchor in the wall as shown.
D) Insert small screw through end of wall strap and into back of
unit as shown.
NOTE: Insert screws 3/4"-1"
from the edge of the strap
wall
strap
large
screw
small
screw
plastic
anchor
WALL
Mounting assembly is now complete.
HINGE ADJUSTMENT
If the doors do not appear square or aligned,
loosen or tighten the appropriate screws on
each case hinge as illustrated.
1)
Side to side adjustment:
Loosen screw A, adjust gap
with screw B and re-tighten
screw A. A.
1
2) Depth adjustment:
Loosen screw A, push hinge arm
forwards or backwards, re-tighten
screw
2
A
NOTE: If you are unsure about your wall
type or what mounting method you should
use, consult a qualified professional or your
local hardware store.
A
B
Made in China - r10 Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 5 of 5
Loading...