HAMMOCK STAND
TOOLS REQUIRED
rubber mallet
COMPONENTS
Thank you for purchasing the Hammock Stand. This
page lists all the contents included in the box. Please
take time to identify the hardware as well as the individual
components of this product. As you unpack and prepare
for assembly, place the contents on a carpeted or padded
area to protect them from damage.
Note: 2 people are required to safely assemble this product.
ASSEMBLY
spring pin
spring pin
2 - wheels
1 - pole insert
with axle
2 - pole inserts
3 - pole sleeves
2 - hooks
1 - hammock
(sold separately)
2 - washers
2 - leg assemblies
(1 left, 1 right)
2 - wheel
caps
right leg
assembly
UNLOCKED
pole insert
1 Fit pole insert into pole sleeve as shown. To secure, push
poles together until spring pin of pole insert locks into hole of
pole sleeve. Make sure spring pin is securely engaged.
LOCKED
pole sleeve
base pole
assembly
left leg
assembly
2 Attach left leg assembly to base pole assembly as
shown. Make sure spring pin of left leg assembly securely
engages hole of base pole assembly.
Repeat for right leg assembly.
Made in China - r03 Page 1 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
HAMMOCK STAND
3 Attach 1 pole insert with axle to left leg
assembly as shown. Make sure spring pin of left
leg assembly securely engages hole of pole insert
with axle.
B) Attach 1 pole insert to right leg assembly.
Make sure spring pin of right leg assembly
securely engages hole of pole insert.
pole insert
pole insert
with axle
A
left leg assembly
4 A) Attach 1 pole sleeve to pole insert with axle
as shown. Make sure spring pin of pole insert with
axle securely engages hole of pole sleeve.
B) Attach 1 pole sleeve to pole insert as shown.
Make sure spring pin of pole insert securely engages
hole of pole sleeve.
C) Attach 1 wheel with 1 washer and 1 axle cap
onto axle as shown. Secure wheel by lighting tapping
axle cap with a rubber mallet.
Repeat for remaining wheel.
D) Insert 1 hook into
each hole of pole
sleeve as shown.
Make sure hooks are
parallel to pole.
D
pole sleeve
A
axle
C
hook
washer
wheel
B
D
axle cap
right leg assembly
D
pole sleeve
B
pole insert
pole insert
with axle
C
Made in China - r03 Page 2 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
HAMMOCK STAND
5 Attach chain of hammock (sold separately) to
hooks at desired height tension. Make sure chain is
securely attached to each hook.
NOTE: Take extreme caution when sitting in your
hammock for the first time. Hammock will stretch.
Once initial stretching occurs, tighten hammock
chains to adjust to desired height tension.
Assembly is now complete.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do
not use abrasive cleaners. It is recommended to
cover the hammock if left outdoors for the winter.
Periodically check the hammock to ensure that
there are no frays in the rope knot and that the
hanging chain is not twisted.
hammock
(sold separately)
CAUTION
• WARNING: Do not exceed load limit of 600 lbs.
• Do not allow children to use the hammock without
adult supervision.
• Do not place infants in the hammock.
• Do not drag or pull the hammock stand when moving
or adjusting. Always lift hammock stand from both ends.
• After moving or adjusting the hammock stand, always
inspect to make sure spring pins are properly installed.
• Do not replace hooks with other hardware.
• Hammock stand should be examined periodically to
ensure that each welded joint is full intact, there is no
excessive rust and that there are no missing caps.
Made in China - r03 Page 3 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...