FARROW 2 DOOR CABINET
Thank you for purchasing the Farrow 2 Door Cabinet.
This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
ASSEMBLY HARDWARE
24 - spring
washers
22 - small
screws
16 - small
flat washers
6 - large
screws
Missing hardware? Please call
800.606.6387 for replacements.
8 - large
flat washers
16 - small
bolts
WALL MOUNTING HARDWARE
4 - small
screws
4 - large
screws
2 - wall
straps
4 - wall
brackets
TOOLS REQUIRED
allen wrench (included)
phillips head screwdriver
(We recommened the use of hand tools instead power tools)
24 - shelf
pins
8 - large
bolts
4 - plastic
anchors
COMPONENTS
1 - top panel
1 - front frame
1 - bottom
panel
2 - side panels
(1 left, 1 right)
1 - back panel
1 - partition
6 - adjustable
shelves
4 - legs
Made in Vietnam - r02 Page 1 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
FARROW 2 DOOR CABINET
NOTE: Do not over
tighten the bolts
leg
bottom
panel
1 Place bottom panel onto a clean, padded surface.
Attach 4 legs to bottom panel with 2 large bolts, 2
spring washers and 2 large flat washers per leg as
shown. Secure, but do not over tighten, bolts using an
allen wrench.
NOTE: Make sure
brackets of side panels
are positioned towards
each other as shown
left side
panel
partition
right side
panel
2 A) With assistance of another adult, position bottom
panel as shown. Attach left and right side panels to
bottom panel with 2 large screws per side as shown.
Secure, but do not over tighten, screws using a phillips
head screwdriver.
B) Attach partition to bottom panel with 2 large screws
as shown.
NOTE: Make sure brackets
of top panel are positioned
towards the front of assembly
as shown.
top
panel
3 Fit pre-assembled dowels of left/right side panels
and partition into corresponding holes of top panel.
Attach top panel to left/right side panels and partition
with 6 small bolts, 6 spring washers and 6 small flat
washers as shown, using a screwdriver.
front frame
4 With the assistance of another adult, position
assembled unit upright. Attach front frame to assembled
unit with 10 small bolts, 10 spring washers and 10
small flat washers as shown, using a screwdriver.
Made in Vietnam - r02 Page 2 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
FARROW 2 DOOR CABINET
A
A
B
adjustable
shelf
back panel
5 Attach back panel to assembled unit with 22 small
screws as shown, using a screwdriver.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth.
Do not use abrasive cleaners. Do not use
furniture wax or polish as the wood is finished
with a protective clear lacquer.
6 A) Insert 24 shelf pins at desired shelf heights.
B) Place 6 adjustable shelves into assembly as shown.
Make sure that each shelf securely supported by each
shelf pin.
Assembly is now complete.
Made in Vietnam - r02 Page 3 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
FARROW 2 DOOR CABINET
SAFETY MOUNTING INSTRUCTIONS:
For added safety and stability, it is recommended that
the wall mounting hardware be installed. For safe
mounting, it is essential to use wall anchors
appropriate to your wall type (i.e. plaster, drywall,
concrete, etc.). Mount to wood studs whenever
possible.
A) Attach 2 wall brackets to back of unit using 4
small screws as shown.
B) Determine the final location of unit. Mark position
on the wall, approximately 2" below each wall bracket
mounted to the back of the unit.
C) Drill a hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller
in diameter than the anchor. Gently tap the plastic
anchor until the flange of the anchor is flush with the
wall.
D) Attach wall brackets to the wall by inserting 2
large screws through each bracket and into each
plastic anchor in the wall.
E) Place the unit so the wall brackets on the back
edge are aligned with the wall brackets on the wall.
F) Lace one end of the wall strap through each
bracket, and into the other end of the strap.
G) Pull the strap tightly until secure.
Wall mounting assembly is now complete.
WALL
C
plastic
anchor
D
large
screw
wall
bracket
A
F
wall
strap
wall
bracket
small
screw
NOTE:
If you are unsure about your wall type or what
mounting method you should use, consult a
qualified professional or your local hardware
store.
Made in Vietnam - r02 Page 4 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...