Crate & Barrel Farrow Entryway Cabinet Assembly Instruction

FARROW ENTRYWAY CABINET
Thank you for purchasing the Farrow Entryway Cabinet. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage.
ASSEMBLY HARDWARE
22 - spring washers
16 - small screws
14 - small flat washers
6 - large screws
Missing hardware? Please call
800.606.6387 for replacements.
8 - large flat washers
14 - small bolts
WALL MOUNTING HARDWARE
4 - small screws
4 - large screws
2 - wall straps
4 - wall brackets
TOOLS REQUIRED
allen wrench (included)
phillips head screwdriver
(We recommened the use of hand tools instead power tools)
16 - shelf pins
8 - large bolts
4 - plastic anchors
COMPONENTS
1 - top panel 1 - front frame
2 - side panels
(1 left, 1 right)
1 - bottom panel
1 - partition
1 - back panel
4 - adjustable shelves
4 - legs
Made in Vietnam - r03 Page 1 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
FARROW ENTRYWAY CABINET
leg
NOTE: Do not over tighten the bolts
bottom panel
1 Place bottom panel onto a clean, padded surface. Attach 4 legs to bottom panel with 2 large bolts, 2 spring washers and 2 large flat washers per leg as shown. Secure, but do not over tighten, bolts using an
allen wrench.
NOTE: Make sure brackets of side panels are positioned towards each other as shown
partition
left side panel
right side panel
B
A
A
2 A) With assistance of another adult, position bottom panel as shown. Attach left and right side panels to bottom panel with 2 large screws per side as shown. Secure, but do not over tighten, screws using a phillips head screwdriver.
B) Attach partition to bottom panel with 2 large screws as shown.
NOTE: Make sure brackets of top panel are positioned towards the front of assembly as shown.
top panel
3 Fit pre-assembled dowels of left/right side panels and partition into corresponding holes of top panel. Attach top panel to left/right side panels and partition with 6 small bolts, 6 spring washers and 6 small flat washers as shown, using a screwdriver.
front frame
4 With the assistance of another adult, position assembled unit upright. Attach front frame to assembled unit with 8 small bolts, 8 spring washers and 8 small flat washers as shown, using a screwdriver.
Made in Vietnam - r03 Page 2 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
FARROW ENTRYWAY CABINET
back panel
5 Attach back panel to assembled unit with 16 small
screws as shown, using a screwdriver.
A
A
B
adjustable shelf
6 A) Insert 16 shelf pins at desired shelf heights. B) Place 4 adjustable shelves into assembly as shown. Make sure that each shelf securely supported by each shelf pin. Assembly is now complete.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the wood is finished with a protective clear lacquer.
Made in Vietnam - r03 Page 3 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
FARROW ENTRYWAY CABINET
SAFETY MOUNTING INSTRUCTIONS:
For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs whenever possible.
A) Attach 2 wall brackets to back of unit using 4 small screws as shown. B) Determine the final location of unit. Mark position on the wall, approximately 2" below each wall bracket mounted to the back of the unit. C) Drill a hole in the wall stud. If the wall stud is not available, drill a hole in the wall that is slightly smaller in diameter than the anchor. Gently tap the plastic anchor until the flange of the anchor is flush with the wall. D) Attach wall brackets to the wall by inserting 2 large screws through each bracket and into each plastic anchor in the wall. E) Place the unit so the wall brackets on the back edge are aligned with the wall brackets on the wall. F) Lace one end of the wall strap through each bracket, and into the other end of the strap. G) Pull the strap tightly until secure. Wall mounting assembly is now complete.
WALL
C
plastic anchor
D
large screw
wall
bracket
A
F
wall strap
wall
bracket
small screw
NOTE: If you are unsure about your wall type or what mounting method you should use, consult a qualified professional or your local hardware store.
Made in Vietnam - r02 Page 4 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...