FARROW 44” CORNER MEDIA CONSOLE
Thank you for purchasing the Farrow 44” Corner Media
Console. This page lists all the contents included in the
box. Please take time to identify the hardware as well as
the individual components of this product. As you
unpack and prepare for assembly, place the contents on
a carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
ASSEMBLY HARDWARE
30 - spring
washers
14 - small
screws
22 - small
flat washers
12 - large
screws
Missing hardware? Please call
800.606.6387 for replacements.
8 - large
flat washers
22 - small
bolts
WALL MOUNTING HARDWARE
4 - small
screws
4 - large
screws
2 - wall
straps
4 - wall
brackets
TOOLS REQUIRED
allen wrench (included)
phillips head screwdriver
(We recommened the use of hand tools instead power tools)
8 - shelf
pins
8 - large
bolts
4 - plastic
anchors
COMPONENTS
1 - top panel 1 - front frame
1 - partition
1 - bottom
panel
2 - side panels
(1 left, 1 right)
2 - adjustable
shelves
2 - door fronts
1 - back
panel
Made in Vietnam - r03 Page 1 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
2 - side back panels
(1 left, 1 right)
1 - bottom
crossbar
4 - legs
FARROW 44” CORNER MEDIA CONSOLE
leg
NOTE: Do not over
tighten the bolts
A
A
right back
panel
right panel
bottom
panel
B
C
B
bottom
crossbar
1 A) Place bottom panel onto a clean, padded surface.
Attach 4 legs to bottom panel with 2 large bolts, 2
spring washers and 2 large flat washers per leg as
shown. Secure, but do not over tighten, bolts using an
allen wrench.
B) Attach 1 bottom crossbar to bottom panel with 2
small bolts, 2 spring washers and 2 small flat washers
as shown, using a phillips head screwdriver.
C) Secure bottom crossbar to bottom panel with 1 large
screw, using a screwdriver.
NOTE: Make sure crossbar
of top panel is positioned
towards the front of assembly
as shown.
partition
left panel
left back
panel
bottom
panel
2 With the assistance of another adult, fit pre-assembled
dowels of left/right side panels, left/right back panels
and partition into corresponding holes of bottom panel.
Secure bottom panel with 11 large screws, using a
screwdriver.
top
panel
front frame
3 Fit pre-assembled dowels of left/right side panels,
left/right back panels and partition into corresponding
holes of top panel. Attach top panel with 8 small bolts,
8 spring washers and 8 small flat washers as shown,
using a screwdriver.
Made in Vietnam - r03 Page 2 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
4 With the assistance of another adult, position
assembled unit upright. Attach front frame to assembled
unit with 12 small bolts, 12 spring washers and 12
small flat washers as shown, using a screwdriver.
FARROW 44” CORNER MEDIA CONSOLE
back panel
A
A
B
adjustable
shelf
5 Attach back panel to assembled unit with 14 small
screws as shown, using a screwdriver.
LOCKED
POSITION
UNLOCKED
POSITION
door front
6 A) Insert 8 shelf pins at desired shelf heights.
B) Place 2 adjustable shelves into assembly as shown.
Make sure that each shelf securely supported by each
shelf pin.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth.
Do not use abrasive cleaners. Do not use
furniture wax or polish as the wood is finished
with a protective clear lacquer.
7 Push pins on top and bottom of door front down so that they are
in the unlocked position. Fit door front into back groove of assembled
unit. Push pins up to secure. Repeat for remaining door front using the
front groove of unit.
Assembly is now complete.
Made in Vietnam - r03 Page 3 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
FARROW 44” CORNER MEDIA CONSOLE
SAFETY MOUNTING INSTRUCTIONS:
For added safety and stability, it is recommended that
the wall mounting hardware be installed. For safe
mounting, it is essential to use wall anchors
appropriate to your wall type (i.e. plaster, drywall,
concrete, etc.). Mount to wood studs whenever
possible.
A) Attach 2 wall brackets to back of unit using 4
small screws as shown.
B) Determine the final location of unit. Mark position
on the wall, approximately 2" below each wall bracket
mounted to the back of the unit.
C) Drill a hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller
in diameter than the anchor. Gently tap the plastic
anchor until the flange of the anchor is flush with the
wall.
D) Attach wall brackets to the wall by inserting 2
large screws through each bracket and each plastic
anchor in the wall.
E) Place the unit so the wall brackets on the back
edge are aligned with the wall brackets on the wall.
F) Lace one end of the wall straps through each
bracket, and into the other end of the strap.
G) Pull the strap tightly until secure.
Wall mounting assembly is now complete.
WALL
C
plastic
anchor
D
large
screw
wall
bracket
A
F
wall
strap
wall
bracket
small
screw
NOTE:
If you are unsure about your wall type or what
mounting method you should use, consult a
qualified professional or your local hardware
store.
Made in Vietnam - r03 Page 4 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...