ELLIS 6 DRAWER DRESSER
HARDWARE
Thank you for purchasing the Ellis 6 Drawer Dresser.
This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from
damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
26 - bolts
26 - spring
washers
Missing hardware?
Please call 800.606.6387 for replacements.
48 - screws
26 - flat
washers
TOOLS REQUIRED
Phillips head screwdriver
1 - back panel
1 - middle panel 6 - drawer
front panels
6 - drawer
left side panels
Made in Vietnam R05 Page 1 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
1 - left
side panel
6 - drawer
bottom panels
6 - drawer
right side panels
1 - right
side panel
1 - top panel1 - front frame
6 - drawer
back panels
1 - support leg
ELLIS 6 DRAWER DRESSER
Make sure the wheels
face towards
the front.
1 With the assistance of another adult, carefully lay
back panel on padded surface. Fit left side panel,
right side panel and middle panel onto back panel
by aligning pre-assembled dowels with corresponding
holes. Secure with 8 bolts, 8 spring washers, and 8
flat washers using a Phillips head screwdriver.
A
90º
B
B
A
2 A) Attach support leg onto assembled unit as
shown. Turn clockwise to secure.
B) Turn 2 pre-installed connecting plates 90º
clockwise on middle panel as shown with a Phillips
head screwdriver.
NOTE: To remove
screws, turn Phillips
head screwdriver
counterclockwise.
3 Remove pre-installed screws located in front frame
as shown with a Phillips head screwdriver. Set aside
screws.
B
A
A
B
4 A) Carefully fit front frame onto assembled unit by
aligning dowels with corresponding holes. As shown,
secure front frame with 6 bolts, 6 spring washers, and
6 flat washers using a Phillips head screwdriver.
B) Secure connecting plates onto front frame with
removed screws using a Phillips head screwdriver.
Made in Vietnam R05 Page 2 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
ELLIS 6 DRAWER DRESSER
Make sure the wheels of the
drawer slides face out and
towards the back
NOTE: Do not over
tighten the screws.
VIEW FROM
BELOW
5 Carefully place assembled unit upright. Fit top panel
onto assembled unit by aligning dowels with
corresponding holes. Secure top panel with 12 bolts,
12 spring washers, and 12 flat washers using a
Phillips head screwdriver.
6 Attach the drawer left side panel to the drawer
front panel and drawer back panel with 4 screws.
Secure with a Phillips head screwdriver. Do not
over tighten the screws.
7 Slide drawer bottom panel into the groove at the
base of drawer assembly.
Made in Vietnam R05 Page 3 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
8 Attach the drawer right side panel to the
assembly with 4 screws. Secure with a Phillips
head screwdriver. Repeat steps 5-7 for each
drawer assembly.
ELLIS 6 DRAWER DRESSER
8 Insert 6 drawer assemblies into the case, fitting
wheels of drawer glide into rail of case glides.
Assembly is now complete.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as the
wood is finished with a protective clear lacquer.
Made in Vietnam R05 Page 4 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
Loading...