DRAKE MEDIA STAND
HARDWARE
Thank you for purchasing the Drake Media Stand. This
page lists all the contents included in the box. Please
take time to identify the hardware as well as the individual
components of this product. As you unpack and prepare
for assembly, place the contents on a carpeted or padded
area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
4 - small
bolts
4 - cams
Missing hardware? Please call 800.606.6387 for replacements.
4 - medium
bolts
8 - flat
washers
8 - large
bolts
8 - spring
washers
8 - wood
dowels
6 - pads
4 - cam
screws
WALL MOUNTING HARDWARE
1 - wall strap 1 - small
screw
1 - large
screw
2 - wall
brackets
1 - plastic
anchor
TOOLS REQUIRED
allen wrench
( We recommend the use of hand tools instead of power tools )
phillips head screwdriver
ASSEMBLY
1 - media stand
assembly
1 - glass tabletop
2 - crossbars 2 - left legs 2 - right legs
1 - tabletop
frame
1 - adjustable
leg
2 - pulls
NOTE: Do not over
tighten the cam screws
A
left leg
A
right leg
Make sure arrows on
each cam point toward
nearest edge with holes
B
crossbar
1 A) Insert 2 wood dowels and 1 cam screw into left and
right legs as shown. Secure, but do not over tighten, using
a phillips head screwdriver.
B) Insert 2 cams into each crossbar as shown. Make sure
arrows on each cam point toward the nearest edge with
holes.
Made in China - r06 Page 1 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
DRAKE MEDIA STAND
media stand
assembly
crossbar
crossbar
right leg
A
B
left leg
2 A) With the assistance of another adult, fit dowels of
left and right leg into corresponding holes of media
stand assembly as shown.
B) Fit dowels of left and right leg into corresponding
holes of crossbars. With a screwdriver, turn cams
clockwise until they securely engage each cam screw.
NOTE: Make sure
brackets of legs
face in as shown
right leg
left leg
A
B
NOTE: Do not over
tighten the bolts
3 A) Fit dowels of left and right leg into corresponding
holes of assembled unit. Secure all cams.
B) Secure left and right legs of assembled unit with 4
large bolts, 4 spring washers and 4 flat washers as
shown, using an allen wrench. Do not over tighten the
bolts.
B
tabletop
assembly
adjustable
leg
leveler
B
A
adjustable
leg
4 A) Attach adjustable leg to assembled unit by turning
leg clockwise to secure. If your table is not level after
assembly is complete, with the assistance of another
adult, adjust leveler of adjustable leg as neccessary.
B) Attach tabletop frame to assembled unit with 4
medium bolts as shown, using an allen wrench.
glass
tabletop
A
pad
B
pull
A
5 A) With the assistance of another adult, position unit
upright. Attach 2 pulls to assembled unit as shown and
secure each pull with 2 small bolts.
B) Adhere 6 pads to tabletop frame as shown and carefully
place glass tabletop onto tabletop frame.
Assembly is now complete.
INSTRUCTION FOR REMOVING DOOR: Lift door and release from bottom groove.
INSTRUCTION FOR INSERTING DOOR: Insert door into top groove and fit into bottom groove.
Made in China - r06 Page 2 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
DRAKE MEDIA STAND
WALL
F
C
D
A
OPTIONAL WALL MOUNTING INSTRUCTIONS
For added safety and stability, it is recommended that the
wall mounting hardware be installed. For safe mounting, it
is essential to use wall anchors appropriate to your wall type
(i.e. plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
A) Attach 1 wall bracket to assembled unit as shown,
using 1 small screw.
B) Determine the final location of dresser unit. Mark
position on the wall, approximately 2" below the bracket
mounted to the back of the unit.
C) Drill a pilot hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in
diameter than the anchor. Insert plastic anchor into hole
and secure using a phillips screwdriver.
D) Attach the wall bracket to the wall by inserting 1 large
screw through the wall bracket and into the plastic anchor
in the wall.
E) Place the unit so the wall bracket on the back edge is
aligned with the wall bracket on wall.
F) Lace one end of the wall strap through both brackets,
and into the other end of the strap.
G) Pull the strap tightly until secure.
NOTE: If you are unsure about your
wall type or what mounting method
you should use, consult a qualified
professional or your local hardware
store.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth.
Do not use abrasive cleaners. Do not use
furniture wax or polish as the wood is finished
with a protective clear lacquer.
Wall mounting assembly is now complete.
Made in China - r06 Page 3 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...