Page 1
DELAVAN TWO DOOR CABINET
Thank you for purchasing the Delavan Two Door
Cabinet. This page lists all the contents included in
the box. Please take time to identify the hardware as
well as the individual components of this product. As
you unpack and prepare for assembly, place the
contents on a carpeted or padded area to protect
them from damage.
Note: 2 people are required to safely assemble this product.
ASSEMBLY HARDWARE
2 - large
screws
26 - spring
washers
18 - small
bolts
26 - flat
washers
Missing hardware? Please call
800.606.6387 for replacements.
8 - large
bolts
4 - pull
bolts
WALL MOUNTING HARDWARE
4 - medium
screws
4 - large
screws
2 - wall
straps
4 - wall
brackets
TOOLS REQUIRED
phillips head screwdriver
(We recommened the use of hand tools instead power tools)
23 - small
screws
16 - shelf
pins
4 - plastic
anchors
COMPONENTS
1 - partition
1 - top
panel
Made in Vietnam - r03 Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
2 - side panels
(1 - left, 1- right)
4 - adjustable
shelves
1 - base
assembly
2 - pulls
NOTE: Do not over tighten
the screws
1 - back panel
1 Fit pre-assembled dowels of partition into corresponding holes of base assembly and secure with 2 large
screws as shown. Secure, but do not over tighten, screws
with a phillips head screwdriver.
1 - front frame
Page 1 of 4
Page 2
DELAVAN TWO DOOR CABINET
NOTE: Do not over
tighten the bolts
B
A
B
A
B
2 A) Place front frame onto clean, padded surface as
shown. Fit dowels of partition into corresponding holes
of front frame as shown. Make sure partition is orientated
as shown during assembly.
B) Attach base assembly to front frame with 4 large
bolts, 4 spring washers and 4 flat washers as shown.
Secure, but do not over tighten, bolts with a phillips head
screwdriver.
B
A
B
3 A) Attach left and right side panels to front frame
with 4 small bolts, 4 spring washers and 4 flat wash-
ers per side panel. Make sure side panels are oriented
as shown during assembly.
B) Secure base frame to side panels with 4 large bolts,
4 spring washers and 4 flat washers as shown.
A
B
A
4 A) Attach top panel to front frame with 4 small bolts, 4
spring washers and 4 flat washers as shown.
B) Secure assembly to top panel with 6 small bolts, 6
spring washers and 6 flat washers as shown.
Made in Vietnam - r03 Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
5 Attach back panel with 23 small screws, using a
screwdriver.
Page 2 of 4
Page 3
DELAVAN TWO DOOR CABINET
A
B
A
B
6 A) With the assistance of another adult, position unit
upright as shown. Insert 16 shelf pins at desired shelf
heights. Place 4 adjustable shelves into assembly as
shown. Make sure each shelf is securely supported by
shelf pins.
B) Attach 1 pull to each door with 2 pull bolts, using a
screwdriver.
Assembly is now complete.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth.
Do not use abrasive cleaners. Do not use
furniture wax or polish as the wood is finished
with a protective clear lacquer.
Made in Vietnam - r03 Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 3 of 4
Page 4
DELAVAN
TWO DOOR CABINET
plastic
C
anchor
wall
F
strap
wall
D
medium
screw
bracket
large
screw
wall
bracket
A
7 Safety Mounting Instructions
For added safety and stability, it is recommended that
the wall mounting hardware be installed. For safe
mounting, it is essential to use wall anchors appropriate
to your wall type (i.e. plaster, drywall, concrete, etc.).
Mount to wood studs whenever possible.
A) Attach wall bracket to top of unit using 2 medium
screws as shown.
B) Determine the final location of unit. Mark position on
the wall, approximately 2" below the wall bracket
mounted to the back of the unit.
C) Drill a hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in
diameter than the anchor. Gently tap the plastic
anchor until the flange of the anchor is flush with the
wall.
D) Attach wall bracket to the wall by inserting 2 large
screws, and into the plastic anchor in the wall.
E) Place the unit so the wall brackets on the back edge
are aligned with the wall brackets on the wall.
F) Lace one end of the wall strap through both
brackets, and into the other end of the strap.
G) Pull the strap tightly until secure.
WALL
NOTE:
If you are unsure about your wall type
or what mounting method you should
use, consult a qualified professional
or your local hardware store.
Repeat steps A-G for remaining wall brackets and wall
straps.
Wall mounting assembly is now complete.
Made in Vietnam - r03 Customer Service 800.967.6696 | Latest instructions available on www.crateandbarrel.com
Page 4 of 4
Loading...