Crate & Barrel Delavan Media-Gaming Tower Assembly Instruction

DELAVAN MEDIA GAMING TOWER
ASSEMBLY HARDWARE
Missing hardware? Please call
800.606.6387 for replacements.
Thank you for purchasing the Delavan Media Gaming Tower. This page lists all the contents included in the
box. Please take time to identify the hardware as well as the individual components of this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage.
COMPONENTS
21 - small screws
10 - spring washers
8 - hinge screws
10 - flat washers
8 - large screws
2 - pull bolts
6 - small bolts
12 - shelf pins
WALL MOUNTING HARDWARE
4 - small screws
4 - large screws
2 - wall straps
4 - wall brackets
TOOLS REQUIRED
phillips head screwdriver
(We recommend the use of hand tools instead power tools)
4 - large bolts
2 - hinges
4 - plastic anchors
2 - side panels
(1 left, 1 right)
1 - bottom panel
1 - fixed shelf
1 - back panel
1 - small adjustable shelf
1 - base assembly
Made in Vietnam - r05 Page 1 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
1 - door front
1 - pull
1 - top panel
2 - large adjustable shelves
DELAVAN MEDIA GAMING TOWER
NOTE: Do not over tighten the bolts
right side panel
fixed shelf
left side panel
1 Fit pre-assembled dowels of fixed shelf into corre­sponding holes of left and right side panels, and attach with 4 large bolts, 4 spring washers and 4 flat washers as shown. Secure, but do not over tighten, the bolts with a phillips head screwdriver.
NOTE: Do not over tighten the screws
top panel
NOTE: Make sure pilot holes of top panel are facing up and towards back during assembly
2 Fit dowels of left and right side panels into corresponding holes of top panel and secure with 4 large screws as shown. Secure, but do not over tighten, the screws using a screwdriver.
A
B
A
bottom panel
base assembly
3 A) Fit dowels of left and right side panels of assembled unit into corresponding holes of bottom panel and secure with 4 large screws as shown. B) Attach base assembly to assembled unit with 6 small
bolts, 6 spring washers and 6 flat washers as shown.
B
back panel
4 With the assistance of another adult, position assem­bly upright as shown. Attach back panel with 21 small screws, using a screwdriver.
Made in Vietnam - r05 Page 2 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
DELAVAN
5 Attach 2 hinges to door front with 2 hinge screws per hinge as shown, using a screwdriver.
MEDIA GAMING TOWER
door front
Refer to Hinge Adjustment diagram for adjusting the alignment of the door hinges
B
A
B
6 A) Attach door front to assembled unit as shown. Secure each hinge with 2 hinge screws. B) Attach pull to door front with 2 pull bolts as shown, using a screwdriver.
A
shelf pin
large adjustable shelf
large adjustable shelf
small adjustable shelf
7 Insert 12 shelf pins at desired shelf heights. Place 1 small and 2 large adjustable shelves into assembly as shown. Make sure each shelf is securely supported by shelf pins. Assembly is now complete.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the wood is finished with a protective clear lacquer.
Made in Vietnam - r05 Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 3 of 4
DELAVAN
MEDIA GAMING TOWER
SAFETY MOUNTING INSTRUCTIONS:
For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs whenever possible.
A) Attach wall bracket to top of unit using 2 small screws as shown. B) Determine the final location of unit. Mark position on the wall, approximately 2" below the wall bracket mounted to the back of the unit. C) Drill a hole in the wall stud. If the wall stud is not available, drill a hole in the wall that is slightly smaller in diameter than the anchor. Gently tap the plastic anchor until the flange of the anchor is flush with the wall. D) Attach wall bracket to the wall by inserting 2 large screws, and into the plastic anchor in the wall. E) Place the unit so the wall brackets on the back edge are aligned with the wall brackets on the wall. F) Lace one end of the wall strap through both brackets, and into the other end of the strap. G) Pull the strap tightly until secure. Repeat steps A-G for remaining wall brackets and
wall straps.
Wall mounting assembly is now complete.
WALL
C
plastic anchor
F
wall strap
A
wall
bracket
large
D
screw
wall
bracket
NOTE: If you are unsure about your wall type or what mounting method you should use, consult a qualified professional or your local hardware store.
small screw
HINGE ADJUSTMENT
If the doors do not appear square or aligned, loosen or tighten the appropriate screws on each case hinge as illustrated.
1) Side to side adjustment: Loosen screw A, adjust gap with screw B and re-tighten screw A.
A
B
1
2) Depth adjustment: Loosen screw A, push hinge arm forwards or backwards, re-tighten screw A and secure screw B with a 1/4 turn clockwise.
A
B
2
3) Height adjustment: Loosen screw C, adjust door height and re­tighten screw C.
C
C
3
Made in Vietnam - r05 Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 4 of 4
Loading...