DELAVAN 62” MEDIA CONSOLE
Thank you for purchasing the Delavan 62” Media Console. This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
ASSEMBLY HARDWARE
2 - large
screws
29 - spring
washers
20 - small
bolts
29 - flat
washers
Missing hardware? Please call
800.606.6387 for replacements.
9 - large
bolts
6 - pull
bolts
WALL MOUNTING HARDWARE
4 - small
screws
4 - large
screws
2 - wall
straps
4 - wall
brackets
TOOLS REQUIRED
phillips head screwdriver
(We recommened the use of hand tools instead power tools)
19 - small
screws
9 - shelf
pins
4 - plastic
anchors
COMPONENTS
1 - base assembly 1 - partition2 - side panels
1 - back panel
(1 left, 1 right)
1 - front frame1 - top panel
1 - small adjustable
shelf
3 - pulls1 - large adjustable
shelf
Made in Vietnam - r08 Page 1 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
DELAVAN 62” MEDIA CONSOLE
1 Fit pre-assembled dowels of partition into corresponding holes of base assembly, and attach with 2
large screws as shown. Secure, but do not over
tighten, the screws with a phillips head screwdriver.
Make sure partition is orientated as shown during
assembly.
A
A
B
B
2 A) Place front frame onto clean, padded surface as
shown. Attach base assembly to front frame with 5
large bolts, 5 spring washers and 5 flat washers as
shown. Secure, but do not over tighten, bolts with a
screwdriver.
B) Attach partition to front frame with 3 small bolts, 3
spring washers and 3 flat washers as shown, using a
screwdriver.
A
A
B
B
3 A) Attach left and right side panels to front frame
with 6 small bolts, 6 spring washers and 6 flat wash-
ers. Make sure side panels are orientated as shown
during assembly.
B) Secure base assembly to side panels with 4 large
bolts, 4 spring washers and 4 flat washers as shown.
A
B
A
4 A) Attach top panel to front frame with 5 small bolts,
5 spring washers and 5 flat washers as shown.
B) Secure assembly to top panel with 6 small bolts, 6
spring washers and 6 flat washers as shown.
B
Made in Vietnam - r08 Page 2 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
DELAVAN
5 With the assistance of another adult, position unit
upright as shown. Insert 9 shelf pins at desired shelf
heights. Place large and small adjustable shelves
into back of assembly as shown. Make sure each
shelf is securely supported by shelf pins.
62” MEDIA CONSOLE
6 With the assistance of another adult, position assembly as shown and attach back panel with 19 small
screws.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth.
Do not use abrasive cleaners. Do not use
furniture wax or polish as the wood is finished
with a protective clear lacquer.
7 Attach 1 pull to each door with 2 pull bolts, using
a screwdriver.
Assembly is now complete.
Made in Vietnam - r08 Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 3 of 4
DELAVAN
62” MEDIA CONSOLE
OPTIONAL WALL MOUNTING ASSEMBLY
For added safety and stability, it is recommended
that the wall mounting hardware be installed. For
safe mounting, it is essential to use wall anchors
appropriate to your wall type (i.e. plaster, drywall,
concrete, etc.). Mount to wood studs whenever
possible.
A) Attach wall bracket to back of unit using 2 small
screws as shown.
B) Determine the final location of unit. Mark
position on the wall, approximately 2" below the wall
bracket mounted to the back of the unit.
C) Drill a hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller
in diameter than the anchor. Gently tap the plastic
anchor until the flange of the anchor is flush with the
wall.
D) Attach wall bracket to the wall by inserting 2
large screws, and into the plastic anchor in the wall.
E) Place the unit so the wall brackets on the back
edge are aligned with the wall brackets on the wall.
F) Lace one end of the wall strap through both
brackets, and into the other end of the strap.
G) Pull the strap tightly until secure.
Repeat steps A-G for remaining wall brackets and
wall straps.
Wall mounting assembly is now complete.
C
F
D
A
WALL
NOTE:
If you are unsure about your
wall type or what mounting
method you should use, consult
a qualified professional or your
local hardware store.
Made in Vietnam - r08 Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 4 of 4
Loading...