Crate & Barrel Delavan 48 Media Console Assembly Instruction

DELAVAN 48” MEDIA CONSOLE
Thank you for purchasing the Delavan 48” Media Con­sole. This page lists all the contents included in the box.
Please take time to identify the hardware as well as the individual components of this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage.
ASSEMBLY HARDWARE
2 - large screws
24 - spring washers
16 - small bolts
24 - flat washers
Missing hardware? Please call
800.606.6387 for replacements.
8 - large bolts
4 - pull bolts
WALL MOUNTING HARDWARE
4 - small screws
4 - large screws
2 - wall straps
4 - wall brackets
TOOLS REQUIRED
phillips head screwdriver
(We recommened the use of hand tools instead power tools)
19 - small screws
8 - shelf pins
4 - plastic anchors
COMPONENTS
2 - pulls
1 - back panel
1 - base assembly 1 - partition2 - side panels
(1 left, 1 right)
1 - front frame1 - top panel
2 - adjustable shelves
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the wood is finished with a protective clear lacquer.
Made in Vietnam - r11 Page 1 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
DELAVAN 48” MEDIA CONSOLE
1 Fit pre-assembled dowels of partition into corre­sponding holes of base assembly, and attach with 2 large screws as shown. Secure, but do not over tighten, the screws with a phillips head screwdriver.
B
A
B
2 A) Place front frame onto clean, padded surface as shown. Fit dowels of partition into corresponding holes of front frame as shown. Make sure partition is orientated as shown during assembly. B) Attach base assembly to front frame with 4 large bolts, 4 spring washers and 4 flat washers as shown. Secure, but do not over tighten, bolts with a screwdriver.
A
B
A
B
3 A) Attach left and right side panels to front frame with 6 small bolts, 6 spring washers and 6 flat wash- ers. Make sure side panels are oriented as shown during assembly. B) Secure base frame to side panels with 4 large bolts, 4 spring washers and 4 flat washers as shown.
A
B
A
4 A) Attach top panel to front frame with 4 small bolts, 4 spring washers and 4 flat washers as shown. B) Secure assembly to top panel with 6 small bolts, 6 spring washers and 6 flat washers as shown.
B
Made in Vietnam - r11 Page 2 of 3
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
DELAVAN
5 With the assistance of another adult, position assem­bly as shown and attach back panel with 19 small screws.
48” MEDIA CONSOLE
B
A
6 A) With the assistance of another adult, position unit upright as shown. Insert 8 shelf pins at desired shelf heights. Place 2 adjustable shelves into assembly as shown. Make sure each shelf is securely supported by shelf pins. B) Attach 1 pull to each door with 2 pull bolts, using a screwdriver. Assembly is now complete.
OPTIONAL WALL MOUNTING ASSEMBLY
For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs whenever possible.
A) Attach wall bracket to back of unit using 2 small screws as shown. B) Determine the final location of unit. Mark position on the wall, approximately 2" below the wall bracket mounted to the back of the unit. C) Drill a hole in the wall stud. If the wall stud is not available, drill a hole in the wall that is slightly smaller in diameter than the anchor. Gently tap the plastic anchor until the flange of the anchor is flush with the wall. D) Attach wall bracket to the wall by inserting 2 large screws, and into the plastic anchor in the wall. E) Place the unit so the wall brackets on the back edge are aligned with the wall brackets on the wall. F) Lace one end of the wall strap through both brackets, and into the other end of the strap. G) Pull the strap tightly until secure. Repeat steps A-G for remaining wall brackets and wall straps. Wall mounting assembly is now complete.
C
F
D
A
WALL
NOTE: If you are unsure about your wall type or what mounting method you should use, consult a qualified professional or your local hardware store.
Made in Vietnam - r11 Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 3 of 3
Loading...