CONTOUR MEDIA STAND
HARDWARE
Thank you for purchasing the Contour Media Stand.
This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
8 - cam
screws
8 - flat
washers
1 - wall
strap
20 - wood
dowels
8 - spring
washers
1 - short
screw
4 - long
bolts
4 - shelf
pins
1 - long
screw
4 - short
bolts
18 - wood
screws
1 - plastic
anchor
8 - cams
Missing hardware? Please call 800.606.6387
for replacements.
4 - barrel
nuts
4 - adjustable
feet
2 - brackets
1 - top
panel
1 - back
4 - legs
panel
1 - bottom
panel
1 - glass
shelf
TOOLS REQUIRED
Made in China - r03 Page 1 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
phillips head screwdriver
2 - side panels
(1 left, 1 right)
2 - front panels
(1 left, 1 right)
allen wrench (included)
CONTOUR MEDIA STAND
A
side
panels
Make sure hole
of each barrel
nut is vertical
front panels
B
1 A) Insert 2 barrel nuts and 2 cams into left and
right side panels as shown. Make sure threaded hole
of each barrel nut is vertically aligned with holes of
side panel. Make sure arrows on each cam points
towards the nearest edge with holes.
B) Insert 4 wood dowels and 2 cams into left and
Make arrow on
each cam points
towards nearest
edge with holes
C
bottom
panel
D
top
panel
right front panels.
C) Insert 2 cam screws and 4 wood dowels into
bottom panel as shown. Secure cam screws, but do
not over tighten with a phillips head screwdriver.
D) Insert 6 cam screws and 4 wood dowels into top
panel as shown.
2 Fit dowels of bottom panel into holes of side
panels. Secure bottom panel with 4 short bolts, 4
spring washers, and 4 flat washers as shown, using
an allen wrench.
A
C
B
3 A) Insert 4 wood dowels into bottom panel as
shown.
B) Attach 4 legs onto assembled unit as shown.
Secure each leg with 1 long bolt, 1 spring washer,
and 1 flat washer, using an allen wrench.
C) Insert 1 adjustable foot into each leg as shown.
Made in China - r03 Page 2 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
CONTOUR MEDIA STAND
4 Fit dowels of left and right front panels and cam
screws of assembled unit as shown. With a
screwdriver, turn each cam clockwise until it securely
engages each cam screw.
5 Fit dowels of assembled unit and cam screws of
top panel as shown. Secure all cams.
B
A
7 Attach back panel onto assembled unit as shown
with 18 wood screws. Secure screws with a
screwdriver.
6 A) Insert 4 shelf pins into assembled unit as
shown.
B) Carefully place glass shelf into assembled unit as
shown.
Made in China - r03 Page 3 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as the
wood is finished with a protective clear lacquer.
CONTOUR MEDIA STAND
8 Safety Mounting Instructions
For added safety and stability, it is recommended that the
wall mounting hardware be installed. For safe mounting, it
is essential to use wall anchors appropriate to your wall type
(i.e. plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
A) Attach 1 bracket to top of media stand as shown, using
1 small screw.
B) Determine the final location of media stand. Mark
position on the wall, approximately 2" below the bracket
mounted to the back of the cabinet.
C) Drill a hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in
diameter than the anchor. Squeeze 2 flanges of plastic
anchor and fit into pre-drilled hole. Gently tap the plastic
anchor until the flange of the anchor is flush with the wall.
D) Attach the remaining bracket to the wall by inserting 1
large screw through the wall bracket and into the wall
anchor in the wall.
E) Place the unit so the bracket on the back edge is allowed
with the bracket on the wall.
F) Lace one end of the wall strap through both brackets,
and into the other end of the strap.
G) Pull the strap tightly until secure.
Assembly is now complete.
short
A
screw
long
D
screw
wall
F
strap
NOTE:
If you are unsure about your wall type or what
mounting method you should use, consult a
qualified professional or your local hardware
store.
This unit can safely hold up to a 24" traditional
(CRT) TV without tipping. This unit can support
up to a 300 lb. TV. Please refer to TV
manufacturer’s recommendations for support
of a flat screen TV.
C
anchor
bracket
Made in China - r03 Page 4 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
Loading...