Crate & Barrel Cabria Buffet with Hutch, Cabria II Buffet with Hutch Top Assembly Instruction

CABRIA BUFFET AND HUTCH

Thank you for purchasing the Cabria Buffet and Hutch.
This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.

Note: 2 people are required to safely assemble this product.

ASSEMBLY HARDWARE

Missing hardware? Please call

800.606.6387 for replacements.

FOR BUFFET

2 - small
screws

2 - large
screws

2 - wall
straps

2 - plastic
anchors

4 - wall
fittings

ASSEMBLY HARDWARE FOR HUTCH

6 - small
screws

2 - large
screws

2 - wall
straps

2 - plastic
anchors

4 - wall
fittings

COMPONENTS

1 - hutch 1 - buffet

TOOLS REQUIRED

phillips head screwdriver

(We recommend the use of hand tools instead of power tools)

2 - connecting
plates

ASSEMBLY WITHOUT HUTCH

adjustable
shelves

The 2 shelves located in the buffet are reversible. One
side provides a flat surface, while the other side provides
rails for wine bottles. Rotate shelf to desired orientation
and insert back into buffet. Make sure each shelf rests
securely on shelf supports.

Option 1: Flat surface Option 2: Wine rack

Made in Indonesia - r06 Page 1 of 3

Customer Service 800.967.6696 | Latest instructions avaliable at www.crateandbarrel.com

CABRIA BUFFET AND HUTCH

WALL MOUNTING ASSEMBLY WITHOUT HUTCH

For added safety and stability, it is recommended that the wall
mounting hardware be installed. For safe mounting, it is
essential to use wall anchors appropriate to your wall type (i.e.
plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
A) Attach 1 wall fitting to assembled unit as shown, using 1
small screw.
B) Determine the final location of unit. Mark position on the
wall, approximately 2" below the bracket mounted to the back
of the unit.
C) Drill a pilot hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in
diameter than the anchor. Gently tap the plastic anchor until
the flange of the anchor is flush with the wall.
D) Attach the wall fitting to the wall by inserting 1 large screw
through the wall fitting and into the plastic anchor in the wall.
E) Place the unit so the wall fitting on the back edge is aligned
with the wall fitting on wall.
F) Lace one end of the wall strap through both fittings, and
into the other end of the strap.
G) Pull the strap tightly until secure.
H) Repeat steps A-G for remaining wall fitting and wall strap.

NOTE:
If you are unsure about your wall type or what
mounting method you should use, consult a
qualified professional or your local hardware
store.

F

wall strap

C

plastic
anchor

D

large screw

A

wall fitting &
small screw

Wall mounting assembly is now complete.

ASSEMBLY WITH HUTCH

connecting
plate

small
screw

With the assistance of another adult, carefully position

hutch on top of buffet as shown. Attach 2 connecting
plates to assembly with 2 small screws per plate as

shown. Secure, but do not over tighten, screws with a
phillips head screwdriver.
Assembly is now complete.

ADJUSTABLE SHELF
ORIENTATIONS

Option 1: Flat surface

Option 2: Wine rack

adjustable
shelves

The 2 shelves located in the buffet are reversible.
One side provides a flat surface, while the other side
provides rails for wine bottles. Rotate shelf to desired
orientation and insert back into buffet. Make sure
each shelf rests securely on shelf supports.

Made in Indonesia - r06 Page 2 of 3

Customer Service 800.967.6696 | Latest instructions avaliable at www.crateandbarrel.com