Page 1
BUNGALOW TALL BOOKCASE
ASSEMBLY HARDWARE
Thank you for purchasing the Bungalow Tall
Bookcase. This page lists all the contents included in
the box. Please take time to identify the hardware as
well as the individual components of this product. As
you unpack and prepare for assembly, place the
contents on a carpeted or padded area to protect them
from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
49 - flat
washers
9 - wood
dowels
14 - short
bolts
30 - medium
bolts
5 - long
bolts
WALL MOUNTING HARDWARE
1 - small
screw
Missing hardware? Please call 800.606.6387 for replacements.
1 - large
screw
1 - metal
anchor
2 - wall
brackets
1 - wall
strap
TOOLS REQUIRED
allen wrench (included)
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
1 - top panel
4 - small partitions
1 - bottom panel
1 - large partition
2 - side panels
(1 left, 1 right)
Made in China - r08 Page 1 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
4 - feet
1 - center support
4 - fixed shelves
Page 2
BUNGALOW TALL BOOKCASE
NOTE: Do not
over tighten bolts.
left side
panel
A
right side
panel
bottom
panel
A
foot
B
long bolt
flat washer
C
1 A) Place bottom panel and left and right side
panels on a clean, padded surface as shown. Insert 9
wood dowels as shown.
B) Attach left and right side panels to bottom panel
with 2 feet, 2 long bolts and 2 flat washers per side
panel frame. Secure, but do not over tighten, bolts
with an allen wrench.
C) Attah center support to bottom panel with 1 long
bolt and 1 flat washer.
center
support
B
C
2 A) Attach 1 small partition to bottom
panel of assembled unit with 2 short bolts
and 2 flat washers as shown. Secure, but
do not fully tighten, bolts with an allen
wrench.
B) Attach 1 fixed shelf to assembled unit
with 6 medium bolts and 6 flat washers
as shown.
Repeat steps A and B for remaining
partitions and fixed shelves.
B
medium bolt
flat washer
A
short bolt
flat washer
fixed
shelf
NOTE: Do not
fully tighten bolts
B
small
partition
A
Made in China - r08 Page 2 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 3
BUNGALOW TALL BOOKCASE
large
top panel
C
B
A
partition
3 A) Attach 1 large partition to assembled unit
with 2 short bolts and 2 flat washers as shown.
B) Attach top panel to side panels of assembled
unit with 4 small bolts and 4 flat washers as
shown.
C) Attach top panel to partition of assembled unit
with 2 medium bolts and 2 flat washers as
shown.
top panel
medium bolt
flat washer
A
short bolt
flat washer
B
short bolt
flat washer
C
medium bolt
flat washer
CLEANING & CARE
Clean surfaces with a dry or damp soft cloth. Do not
use abrasive cleaners. Do not use furniture wax or
polish as the unit is finished with a protective clear
lacquer. It is recommended to use coasters to
protect surface from heat and water.
4 Secure top panel with 4 medium bolts and 4 flat
washers. At this point, fully tighten all bolts with an allen
wrench. With the assistance of another adult, carefully
position unit upright.
Assembly is now complete.
Made in China - r08 Page 3 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 4
BUNGALOW TALL BOOKCASE
F
wall strap
D
large screw
A
wall bracket &
small screw
C
metal
anchor
NOTE: If you are unsure about your
wall type or what mounting method
you should use, consult a qualified
professional or your local hardware
store.
WALL MOUNTING INSTRUCTIONS
For added safety and stability, it is recommended that the
wall mounting hardware be installed. For safe mounting, it
is essential to use wall anchors appropriate to your wall
type (i.e. plaster, drywall, concrete, etc.). Mount to wood
studs whenever possible.
A) Attach 1 wall bracket to assembled unit as shown,
using 1 small screw.
B) Determine the final location of dresser unit. Mark
position on the wall, approximately 2" below the bracket
mounted to the back of the unit.
C) Drill a pilot hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in
diameter than the anchor. Insert metal anchor into hole
and secure using a phillips screwdriver.
D) Attach the wall bracket to the wall by inserting 1 large
screw through the wall bracket and into the metal anchor
in the wall.
E) Place the unit so the wall bracket on the back edge is
aligned with the wall bracket on wall.
F) Lace one end of the wall strap through both brackets,
and into the other end of the strap.
G) Pull the strap tightly until secure.
Wall mounting assembly is now complete.
Made in China - r08 Page 4 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...