Page 1
BUNGALOW MEDIA STAND
ASSEMBLY HARDWARE
Thank you for purchasing the Bungalow Media Stand.
This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
16 - shelf
pins
18 - medium
bolts
25 - spring
washers
7 - large
bolts
25 - flat
washers
Missing hardware?
Please call 800.606.6387
for replacements.
4 - small
bolts
WALL MOUNTING HARDWARE
1 - medium
screw
1 - large
screw
1 - metal
anchor
2 - wall
brackets
TOOLS REQUIRED
allen wrench (included)
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
2 - small
screws
1 - wall
strap
2 - pulls
1 - top panel
2 - side panels
(1 left, 1 right)
1 - center
support
4 - feet
Made in China - r11 Page 1 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
4 - adjustable
shelves
1 - bottom panel
1 - front frame1 - partition 1 - back panel
Page 2
BUNGALOW MEDIA STAND
left side
panel
NOTE: Do not over tighten bolts.
right side
panel
1 Place top panel onto clean, padded surface as
shown. Attach left and right side panels to
assembled unit with 2 medium bolts, 2 spring
washers and 2 flat washers per side panel using an
allen wrench.
medium bolt
spring washer
flat washer
front
frame
top panel
2 Attach front frame to top panel of assembled unit
with 4 medium bolts, 4 spring washers and 4 flat
washers. Secure, but do not over tighten, bolts with an
allen wrench.
medium bolt
spring washer
partition
flat washer
3 Attach partition to assembled unit with 2 medium
bolts, 2 spring washers and 2 flat washers.
back panel
4 Slide back panel into corresponding grooves of side
panels as shown. Secure back panel with 2 small screws as
shown, using screwdriver.
Made in China - r11 Page 2 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 3
BUNGALOW MEDIA STAND
A
B
bottom
panel
5 With the assistance of another adult, position bottom
panel onto assembled unit as shown. Secure bottom panel
to front/side panels with 8 medium bolts, 8 spring washers
and 8 flat washers using an allen wrench.
B) Secure bottom panel to partition with 2 large bolts, 2
spring washers and 2 flat washers as shown.
large
bolt
spring
washer
flat
center
support
foot
washer
6 Fit dowel of center support into corresponding holes
of assembled unit as shown. Attach each foot and
center support to bottom panel with 1 large bolt, 1
spring washer and 1 flat washer. Secure, but do not
over tighten, bolt with an allen wrench.
pull
7 Attach 1 pull to each door with 2 small bolts using
an allen wrench.
A
adjustable
B
shelves
NOTE: Make sure shelf
is securely supported
by shelf pins
8 A) Insert 16 shelf pins into holes at the desired shelf
height. Turn pin clockwise to secure.
B) Place adjustable shelves into assembled unit. Make
sure shelves are securely supported by shelf pins. If the left
door is lower then the right door raise the left side leveling
feet. If the right door is lower then the left door raise the
right side leveling feet.
Assembly is now complete.
A
Made in China - r11 Page 3 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 4
BUNGALOW MEDIA STAND
F
wall strap
D
large screw
A
wall bracket &
small screw
C
metal
anchor
WALL MOUNTING INSTRUCTIONS
For added safety and stability, it is recommended that the
wall mounting hardware be installed. For safe mounting, it
is essential to use wall anchors appropriate to your wall
type (i.e. plaster, drywall, concrete, etc.). Mount to wood
studs whenever possible.
A) Attach 1 wall bracket to assembled unit as shown,
using 1 small screw.
B) Determine the final location of dresser unit. Mark
position on the wall, approximately 2" below the bracket
mounted to the back of the unit.
C) Drill a pilot hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in
diameter than the anchor. Insert metal anchor into hole
and secure using a phillips screwdriver.
D) Attach the wall bracket to the wall by inserting 1 large
screw through the wall bracket and into the metal anchor
in the wall.
E) Place the unit so the wall bracket on the back edge is
aligned with the wall bracket on wall.
F) Lace one end of the wall strap through both brackets,
and into the other end of the strap.
G) Pull the strap tightly until secure.
NOTE: If you are unsure about your wall type or
what mounting method you should use, consult a
qualified professional or your local hardware
store.
Wall mounting is recommended; however, is not
necessary for 27” Conventional TV and/or 40’’
Flat Panel TV
CLEANING & CARE
Clean surfaces with a dry or damp soft cloth. Do
not use abrasive cleaners. Do not use furniture
wax or polish as the unit is finished with a
protective clear lacquer. It is recommended to use
coasters to protect surface from heat and water.
Wall mounting assembly is now complete.
Made in China - r11 Page 4 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...