Crate & Barrel Brey Bookcase Assembly Instruction

ASSEMBLY HARDWARE
Thank you for purchasing the Brey Bookcase. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
C
A B
D
1 - top back crossbar
1 - top front crossbar
20 - spring washers
16 - bumpers
4 - large
washers
Missing hardware? Please call 800.606.6387 for replacements.
screws
56 - small screws
20 - bolts20 - flat
WALL MOUNTING HARDWARE
2 - wall straps 4 - brackets 4 - plastic
4 - small screws
4 - large screws
anchors
TOOLS REQUIRED
allen wrench (included)
(We recommend the use of hand tools instead of power tools)
phillips head screwdriver
K
1 - top back panel
E
F
G
H
2 - side frames
(1 left, 1 right)
Made in Vietnam - r02 Page 1 of 5
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
3 - middle back crossbars
3 - middle front crossbars
1 - bottom back crossbar
1 - bottom front crossbar
J
4 - glass shelves
L
M
2 - middle back panels
1 - bottom back panel
I
1 - top panel
bottom front crossbar
H
bottom back crossbar
A
middle back crossbar
E
left side panel
G
NOTE: Make sure holes of back crossbars all face out as shown
middle front crossbar
F
middle back crossbar
E
middle front crossbar
F
middle back crossbar
E
middle front crossbar
F
top back crossbar
C
1 Fit dowels of top, middle and bottom front and back crossbars into corresponding holes of left side frame as shown. Secure each crossbar with 1 bolt, 1 spring washer and 1 flat washer, using an allen wrench. Do not over tighten the bolts.
top front crossbar
D
NOTE: Do not over tighten the bolts
B
right side panel
2 Fit dowels of front and back crossbars into corresponding holes of right side frame as shown. Secure each crossbar with 1 bolt, 1 spring washer and 1 flat washer, using an allen wrench.
Made in Vietnam - r02 Page 2 of 5
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
NOTE: Do not over tighten the screws
M
bottom back panel
L
middle back panel
L
3 Place 1 bottom back panel, 2 middle back panels and 1 top back panel to assembly as shown. Secure back panels with 56 smalls screws using a phillips head screwdriver. Do not over tighten the
screws.
middle back panel
top back panel
K
4 Attach 1 top panel to assembly with 4 large screws as shown, using a screwdriver.
I
top panel
Made in Vietnam - r02 Page 3 of 5
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
BREY BOOKCASE
5 A) With the assistance of another adult, position unit upright. Adhere 16 bumpers to assembly as shown. B) Carefully fit 4 glass shelves into unit as shown. Make sure each shelf is fully supported by crossbars.
Assembly is now complete.
A
J
J
J
J
glass shelf
glass shelf
glass shelf
glass shelf
A
B
CLEANINGANDCARE
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the unit is finished with a protective lacquer. Wipe clean glass with glass cleaner and lint free cloth.
MadeinVietnam - r02 Page4of5
CustomerService800.967.6696 | Latestinstructionsavailableatwww.crateandbarrel.com
WALL MOUNTING INSTRUCTIONS:
For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs whenever possible. The following instructions are for drywall mounting only.
NOTE: If you are unsure about your wall type or what mounting method you should use, consult a qualified professional or your local hardware store.
A) Attach 2 wall brackets to back of unit using 4 small screws as shown.
B) Determine the final location of unit. Mark position on the wall, approximately 2" below each wall bracket mounted to the back of the unit. C) Drill a hole in the wall stud. If the wall stud is not available, drill a hole in the wall that is slightly smaller in diameter than the anchor. Gently tap the plastic anchor until the flange of the anchor is flush with the wall. D) Attach wall brackets to the wall by inserting 2 large screws through each bracket and each plastic anchor in the wall. E) Place the unit so the wall brackets on the back edge are aligned with the wall brackets on the wall. F) Lace one end of the wall straps through each bracket, and into the other end of the strap. G) Pull the strap tightly until secure. Wall mounting assembly is now complete.
WALL
C
plastic anchor
D
large screw
A
small screw
wall
bracket
F
wall strap
wall
bracket
Made in Vietnam - r02 Page 5 of 5
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...