Crate & Barrel Belmont 42 Wall Shelf Assembly Instruction

BELMONT 42” WALL SHELF

ASSEMBLY HARDWARE

Missing hardware?
Please call 800.606.6387

4 - large
screws

4 - plastic
anchors

for replacements.

OPTIONAL MOUNTING HARDWARE

Thank you for purchasing the Belmont 42” Wall Shelf.
This page lists all the contents included in the box.
Please take time to identify the hardware as well as the
individual components of this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.

WALL

C

wall
bracket

D

WALLSIDE VIEW

E

wall shelf

wall brackets

2 - medium
screws

2 - plastic
anchors

TOOLS REQUIRED

phillips head screwdriver

(We recommend the use of hand tools instead of power tools)

COMPONENTS

1 - wall bracket 1 - wall shelf

assembly

INSTALLATION INSTRUCTIONS

The wall mounting hardware included with this shelf is intended for
drywall installation only. Be sure to use hardware appropriate for
your wall type. Fasten at least one screw directly into wall stud. If you
are unsure about your wall type or what mounting method you should
use, consult a qualified professional or your local hardware store.

A) Determine the wall location and place the wall bracket into
position. Make sure the pointed side of the bracket points up. There
are 17 holes in the bracket. Choose 4 of these holes for anchoring
into the wall, aligning at least 1 hole with a wall stud. Level and mark
the 4 hole locations on the wall.
B) If attaching directly into wall studs, skip to step D.
C) For drywall installation, drill a hole in the wall stud. If the wall stud is

not available, drill a hole in the wall that is slightly smaller in diameter than
the anchor. Gently tap 1 plastic anchor at each marked hole location,

tightening with a phillips head screwdriver until the head of each
anchor is flush to the wall surface.
D) Insert 1 screw through each hole in the wall bracket and
into the corresponding anchors or studs in the wall. Fully
tighten each screw with a phillps head screwdriver but do not
over tighten
E) With the assistance of another adult, fit the angled bracket on the
back of the unit onto the wall bracket. Make sure the unit is firmly
seated in the wall bracket.
Installation is now complete.

Made in Thailand - r09 Page 1 of 2

Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com

BELMONT 42” WALL SHELF

OPTIONAL MOUNTING INSTRUCTIONS

The wall mounting hardware included with this shelf
is intended for drywall installation only. Be sure to
use hardware appropriate for your wall type.
Whenever possible, fasten screws directly into wall
stud. If you are unsure about your wall type or what
mounting method you should use, consult a
qualified professional or your local hardware store.

A) Determine the final location of unit. Mark positions
of holes of mounting brackets (pre-installed) on wall.
B) Drill a hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller

in diameter than the anchor. Gently tap 1 plastic

anchor at each marked hole location, tightening
with a phillips head screwdriver until the head of
each anchor is flush to the wall surface.

C) Attach the mounting brackets to the wall by
inserting 1 medium screw through each mounting
bracket and into the wall anchor or stud in the wall as
shown. Please note the top of the mounting bracket
will be visible above the top of the shelf.

C

mounting
bracket

(pre-installed)

medium
screw

B

plastic
anchor

Installation is now complete.

WALL

CLEANING AND CARE

Clean surfaces with a dry or damp soft cloth. Do
not use abrasive cleaners. Do not use furniture
wax or polish on the shelf base as the base is
finished with a protective clear lacquer.

Made in Thailand - r09 Page 2 of 2

Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com