ADD CD WALL SHELF
HARDWARE
Thank you for purchasing the Add CD Wall Shelf. This
page lists all the contents included in the box. Please
take time to identify the hardware as well as the individual
components of this product. As you unpack and prepare
for assembly, place the contents on a carpeted or
padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
16 - plastic
dowels
3 - drywall
anchors
Missing hardware? Please call 800.606.6387 for replacements.
3 - large
screws
3 - wall
anchors
(others)
3 - medium
screws
1 - glue
3 - small
screws
4 - connecting
bolts
TOOLS REQUIRED
Phillips head screwdriver
rubber mallet
1 - top horizontal
4 - end caps
2 - cleats
(1 - shelf, 1 - wall)
Made in Thailand R05 Page 1 of 4
1 - back
panel
2 - vertical
panels
Customer Service 800.967.6696 | www.crateandbarrel.com
panel
1 - bottom horizontal
panel
ADD CD WALL SHELF
A
NOTE: Wipe excess glue
with a damp cloth.
NOTE: Do not over
tighten the bolts.
B
1 A) Apply glue sparingly into holes provided on
end caps. Insert 4 plastic dowels into each panel.
Gently tap dowels with rubber mallet to secure.
Wipe excess glue with a damp cloth.
B) Insert 2 connecting bolts into vertical panels.
Secure bolts with a Phillips head screwdriver, but
do not over tighten.
2 Apply glue sparingly into holes provided on
vertical panels. Fit vertical panels into top cap and
bottom cap, by aligning holes with corresponding
plastic dowels. Gently tap assembled panels with
rubber mallet to secure.
A
4 A) Locate the assembled unit with 4 connecting
bolts on the vertical panels. Attach back panel to
3 Apply glue sparingly into holes provided on top
horizontal panel and bottom horizontal panel. Fit
side caps into top horizontal panel and bottom
horizontal panel. Gently tap assembled panels with
rubber mallet to secure.
Made in Thailand R05 Page 2 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
assembled unit as shown, by aligning the
corresponding holes with connecting bolts.
B) Use a Phillips head screwdriver, turn built-in
cams located on back panel clockwise until it
securely engages each connecting bolt.
B
ADD CD WALL SHELF
SIDE VIEW
back
panel
shelf
screws
cleat
5 Attach shelf cleat to back panel of assembled
unit as shown. Secure cleat with 3 small screws
using a Phillips head screwdriver.
6 Carefully attach both assembled units together, by
interlocking corresponding grooves located on
vertical and horizontal panels. Gently tap
assembled panels with rubber mallet to secure.
Assembly is now complete.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as the
wood is finished with a protective clear lacquer.
Made in Thailand R05 Page 3 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
ADD CD WALL SHELF
SIDE VIEW
wall
cleat
wall
cleat
anchor
wall
anchor
screws wall / drywall
screws wall
For all other wall
For drywall installation:
3 - medium
screws
3 - drywall
anchors
installation types:
3 - large
screws
3 - wall
anchors
WALL MOUNTING INSTRUCTIONS
There are 2 types of hardware included, 1 group for drywall
installation and 1 group for all other hollow wall installation
types. Be sure to use hardware appropriate for your wall
type. Whenever possible, attach mounting hardware into a
wall stud. (Do not use anchors if attaching to wall studs
directly.)
If you are unsure about your wall type or what mounting
method you should use, consult a qualified professional or
your local hardware store.
1. Determine the wall location and place the wall bracket
into position. Make sure the pointed side of the bracket
points up. There are 3 holes in the bracket. Level and mark
the 3 hole locations on the wall.
2. If attaching directly into wall studs, skip to Step 5.
3. For drywall installation, drill 3 holes slightly smaller in
diameter than the size of the anchor, but 1/4" deeper than
the length of the anchor. Insert 3 drywall anchors so that
they are flush with the surface of the wall. Gently tap with a
hammer if necessary.
4. For hollow walls, drill 3 holes slightly smaller in diameter
than the size of the anchor. Fold the tabs of the anchor flat,
and insert into the holes until head is flush to the surface of
the wall.
5. Insert 1 medium or large screw through each hole in the
wall bracket and into the corresponding anchors or studs in
the wall. Fully tighten each screw with a Phillips head
screwdriver but do not over tighten.
6. With the assistance of another adult, fit the shelf cleat on
the back of the unit onto the wall cleat. Make sure the unit
is firmly seated in the wall bracket. Installation is now
complete.
Made in Thailand R05 Page 4 of 4
Customer Service 800.967.6696 | www.crateandbarrel.com
Loading...