ABBOTT MEDIA GAMING TOWER
ASSEMBLY HARDWARE
Thank you for purchasing the Abbott Media Gaming
Tower. This page lists all the contents included in the
box. Please take time to identify the hardware as well as
the individual components of this product. As you
unpack and prepare for assembly, place the contents on
a carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
COMPONENTS
12 - bolts
12 - shelf
pins
24 - screws
2 - hinges
WALL MOUNTING HARDWARE
1 - wall strap
Missing hardware?
Please call 800.606.6387 for replacements.
1 - wall screw
TOOLS REQUIRED
phillips head screwdriver
(We recommend the use of hand tools instead power tools)
12 - wood
dowels
2 - hinge
plates
2 - side panels
(1 left, 1 right)
1 - top panel
1 - door
front
Made in China - r06 Page 1 of 4
1 - fixed shelf
2 - large
shelves
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
1 - back panel
1 - bottom
panel
1 - small
shelf
left and right
side panel
1 Insert 6 wood dowels into left and right side panels
as shown.
ABBOTT MEDIA GAMING TOWER
NOTE: Do not over
tighten the bolts
right side
panel
fixed shelf
top panel
left side
panel
bottom
panel
1 Fit dowels of left and right side panels into
corresponding holes of fixed shelf and bottom panel
and secure each with 4 bolts as shown. Secure, but do
not over tighten, the bolts with a phillips head
screwdriver.
NOTE: Do not over
tighten the screws
back panel
2 Fit dowels of left and right side panels into
corresponding holes of top panel and secure with 4
bolts as shown, using a screwdriver.
door front
4 With the assistance of another adult, position
assembled unit upright as shown. Attach back panel with
5 Attach 2 hinges to door front with 2 screws per
hinge as shown, using a screwdriver.
12 screws, using a screwdriver. Do not over tighten the
screws.
Made in China - r06 Page 2 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
ABBOTT
MEDIA GAMING TOWER
Refer to Hinge Adjustment
diagram for adjusting the
alignment of the door
hinges
A
B
NOTE: Door can be
attached to either side of
assembled unit. Pilot holes
on both sides.
A
6 A) Attach 2 hinge plates to assembled unit as shown. Secure
each hinge plate with 4 screws.
B) Detach hinge bolts in hinge plates using a screwdriver. Fit
hinges of door front into corresponding hinge plates of
assembled unit as shown. Secure each hinge with 1 hinge bolt.
B
door front
HINGE ADJUSTMENTS
If the doors do not appear aligned,
refer to the instructions below:
1) Side to side adjustment:
Loosen screw A, adjust gap
with screw B and re-tighten
screw A.
2) Depth adjustment:
Loosen screw A, push hinge
arm forwards or backwards,
re-tighten screw A and secure
screw B.
A
1
B
A
2
B
shelf pin
large shelf
A
large shelf
B
small shelf
7 A) Insert 8 shelf pins at desired shelf heights. Place
2 large shelves into assembly as shown.
B) Place 1 small shelf into assembly as shown. Insert 4
shelf pins at desired shelf height. Make sure each shelf
is securely supported by shelf pins.
Assembly is now complete.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as
the wood is finished with a protective clear lacquer.
Made in China - r06 Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Page 3 of 4
ABBOTT
MEDIA GAMING TOWER
SAFETY MOUNTING INSTRUCTIONS
For added safety and stability, it is recommended that the wall
mounting hardware be installed. For safe mounting, it is essential
to use wall anchors appropriate to your wall type (i.e. plaster,
drywall, concrete, etc.). Mount to wood studs whenever possible.
NOTE: Insert screws 3/4"-1"
from the edge of the strap
WALL
A. Insert wall screw (not included) through end of wall strap and
into wall as shown.
B. Insert wall screw (included) through end wall strap and into the
top back of unit as shown.
Mounting assembly is now complete.
NOTE: If you are unsure about your wall type or what mounting
method you should use, consult a qualified professional or your
local hardware store.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use abrasive
cleaners. Do not use furniture wax or polish as the wood is finished
with a protective clear lacquer.
wall
strap
wall
screw
wall
screw
(NOTE: Additional
screw not included.
Please consult your
local hardware store.)
Made in China - r06 Page 4 of 4
Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com
Loading...