Crate Amplifiers TX50DE User Manual

Page 1
Driver’s Guide
for the
CRATE LIMO
battery powered amplifier
with the new rugged, lightweight molded polymer enclosure!
Page 2
CRATE
CONGRATULATIONS!
You are now the proud owner of the Crate TX50DE battery powered ampli­fier with Digital Signal Processing. At last, you can take your music with you and have great tone on the road. Not only is the TX50DE compact and portable, it also sports two separate channels and the incredible sound that has made Crate a household name among musicians. The high tech poly­mer enclosure makes the amplifier lighter and even more portable!
Your Crate amplifier is musician-made in the U.S.A. using the finest com­ponents available. Each unit is rigorously tested by skilled technicians and musicians to ensure that your amplifier is the best it can be!
In order to get the most out of your new amplifier, we strongly urge you to go over the information contained in this manual before you begin playing.
Thanks for choosing
CRATE.
CONTENTS:
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
About the Power Supply . . . . . . . . . . . . . . .4,5
The Front Panel . . . . . . . . . . . . . . . . . . . . . .6,7
The Rear Panel . . . . . . . . . . . . . . . . . . . . . . .8
About the Insert Jack . . . . . . . . . . . . . . . . . . .8
Suggested Setups . . . . . . . . . . . . . . . . . . .9,10
System Block Diagram . . . . . . . . . . . . . . . . . .11
Technical Specifications . . . . . . . . .back cover
IMPORTANT SAFETY INSTRUCTIONS
READ, FOLLOW, HEED, AND KEEP ALL INSTRUCTIONS AND WARNINGS.
DO NOT OPERATE NEAR ANY HEATSOURCE AND DO NOT BLOCK ANY VENTILATION OPENINGS ON THIS APPARATUS. FOR
PROPER OPERATION, THIS UNITREQUIRES 3” (75mm) OF WELL VENTILATED SPACE AROUND HEATSINKS AND OTHER AIR FLOW PROVISIONS IN THE CABINET.
DO NOT USE THIS APPARATUS NEAR SPLASHING, FALLING, SPRAYING, OR STANDING LIQUIDS.
CLEAN ONLY WITH LINT-FREE DAMP CLOTH AND DO NOTUSE CLEANING AGENTS.
ONLY CONNECT POWER CORD TO APOLARIZED, SAFETY GROUNDED OUTLET WIRED TO CURRENTELECTRICAL CODES AND
COMPATIBLE WITH VOLTAGE, POWER, AND FREQUENCY REQUIREMENTS STATED ON THE REAR PANEL OF THE APPARATUS.
PROTECT THE POWER CORD FROM DAMAGE DUE TO BEING WALKED ON, PINCHED, OR STRAINED.
UNPLUG THE APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.
ONLY USE ATTACHMENTS, ACCESSORIES, STANDS, OR BRACKETS SPECIFIED BY THE MANUFACTURER FOR SAFE OPERA-
TION AND TO AVOID INJURY.
THIS APPARATUS DOES NOT OPERATE NORMALLY AND REQUIRES SERVICE WITH ANY PHYSICALDAMAGE FROM IMPACT OR
ANY EXPOSURE TO MOISTURE.
SERVICE MUST BE PERFORMED BY QUALIFIED PERSONNEL.
OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED EXPOSURE TO HIGH SOUND
PRESSURE LEVELS CAN CAUSE PERMANENT HEARING IMPAIRMENT OR LOSS. USER CAUTION IS ADVISED AND EAR PRO­TECTION IS RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOIS­TURE. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
"IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL" “ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES.” "REFERREZ-VOUS AU MANUAL D'UTILISATION"
EXPLANATION OF GRAPHICAL SYMBOLS: EXPLICACION DE SIMBOLOS GRAFICOS: EXPLICATION DES SYMBÔLES GRAPHIQUES:
"DANGEROUS VOLTAGE" “VOLTAJE PELIGROSO” "DANGER HAUTE TENSION"
=
=
PRECAUCION
RIESGO DE CORRIENTAZO
NO ABRA
PRECAUCION: PARA REDUCIR EL RIESGO DE INCENDIOS O DESCARGAS ELECTRICAS, NO PERMITA QUE ESTE APARATO QUEDE EXPUESTO A LA LLUVIA O LA HUMEDAD. PARA DISMINUOIR EL RIESGO DE CORRIENTAZO. NO ABRA LA CUBIERTA. NO HAY PIEZAS ADENTRO QUE EL USARIO PUEDO REPARAR DEJE TODO MANTENIMIENTO A LOS TECHNICOS CALIFICADOS.
ATTENTION
RISQUE D'ELECTROCUTION
NE PAS OUVRIR
ATTENTION: PROTÉGEZ CET APPAREIL DE LA PLUIE ET DE L'HUMIDITÉ AFIN D'ÉVITER TOUT RISQUE D'INCENDIE OU D'ÉLECTROCUTION. POUR REDUIRE D'ELECTROCUTION NE PAS ENLEVER LE COUVERCLE. AUCUNE PIECE INTERNE N'EST REPRABLE PAR L'UTILISATEUR. POUR TOUTE REPARATION, S'ADRESSER A UN TECHNICIEN QUALIFIE.
Page 3
CRATE
3
FEA
TURES:
• Two separate channels
• Crate’s Digital Signal Processing (DSP)
• Insert jack for connecting external effects
• CD Inputs for connecting background music
• Footswitch control of channel selection and DSP on/off
• Headphones jack for silent operation
• Internal rechargeable power supply for up to 8 hours of normal play­ing time, 2 hours at full output – fully recharges within 6 hours (when battery is fully discharged; shorter if partially charged)
• Two-color battery status LED – red indicates low battery, yellow indi­cates battery okay
• Can also be powered by an AC wall adapter (supplied) or by a 12 volt vehicle car adapter (included – see page 5)
• Tuned port cabinet for extended bass response; 10” woofer and 2” Piezo tweeter for full range sound with clear highs
• Durable black or platinum molded polymer enclosure
• Rubber feet on three sides – for positioning as a low angle monitor, a high angle monitor or as an upright speaker (see below)
• Stand mount adapter (1-1/2” diameter) for PA use (see below)
LOW ANGLE MONITOR HIGH ANGLE MONITOR
UPRIGHT SPEAKER STAND MOUNTED SPEAKER
Page 4
CRATE
4
ABOUT
THE POWER SUPPLY:
The TX50DE uses a sealed lead-acid 12-volt battery as its internal power source. Unlike ni-cad batteries, this battery has no “memory” – it can be fully recharged at any time, without damage to the battery.
When fully charged, the LED next to the power switch will illuminate yellow with the switch at the on (“I”) position. The LED will change to red when the battery is low and needs recharging. When this happens, turn the amp off, connect the 15-volt charger to the charger jack and plug it in. The LED near the charger jack will glow red while the amp is charging and goes out when the amp is fully charged. The battery fully recharges within 6 hours, providing up to 8 hours of use at low levels, about 4 hours of use at moderate levels, and about 2 hours of use at continuous full power (sine wave). The battery is rated for up to 1000 charging cycles. The charger can also function as an AC power supply.
The battery inside the TX50DE must be fully charged before operating the amplifier for the first time. The amplifier leaves our factory with a fully charged battery. However, the battery may lose some of its charge during transit.
NOTE: If the battery is drained too low, the Power LED will go out. This indicates an exhausted battery – one which may not take a charge. If this happens, turn the amp off, connect the 15-volt charger to the charger jack and plug it in. If the Charger LED (see #25, page 8) doesn’t illuminate, the battery might be beyond recharging. (The TX50DE uses a “smart” charging circuit and will not allow you to charge a defective battery.) If the battery is serviceable, the LED will illuminate once the battery reaches 10 volts – leave the charger plugged in and let the bat­tery fully recharge. If the LED never illuminates, the battery may need replacing. Contact Crate’s service department:
SLM Electronics 1901 Congressional Drive St. Louis, MO 63146 1-800-738-PARTS (7563)
To avoid damaging the amplifier, do not connect the supplied 15VAC charger to the amplifier’s 12VDC Cigarette Lighter Adapter jack. Dispose of battery properly.
Page 5
CRATE
5
ABOUT
THE POWER SUPPLY (continued):
The TX50DE may also be powered by using a 12-volt vehicle cigarette lighter adapter, available at most electronic supply stores. Make certain that the polarity on the adapter matches what is shown below.
Connect the small round end of the adapter to the 12VDC Automobile adapter jack (#26, page 8), then connect the other end of the adapter into the vehicle’s cigarette lighter socket. (In some vehicles, the ignition switch must be in the “on” or “accessory” position to have power at the socket.) NEVER PLUG THE SUPPLIED 15VDC CHARGER INTO THE AMPLIFIER’S 12VDC LIGHTER PLUG!
When using the DC cigarette lighter adapter, the vehicle’s battery will keep the amp charged to its own voltage level – if the battery has a
13.5-volt charge, the amp will charge up to 13.5 volts; if the battery is low and only has a 10-volt charge, the amp will discharge down to 10 volts.
POSITIVE NEGATIVE
Page 6
CRATE
6
THE
FRONT PANEL:
1. LOW Z: Connect a low impedance micro­phone here by means of a shielded signal cable terminated with an XLR type connector.
2. HIGH Z: Connect a high impedance micro­phone here by means of a shielded signal cable terminated with a 1/4 connector.
3. LEVEL: Use this control to adjust the output level of the mic channel.
4. LOW: Use this control to adjust the low fre­quency level for the mic channel.
5. MID: Use this control to adjust the mid fre­quency level for the mic channel.
6. HIGH: Use this control to adjust the high fre­quency level for the mic channel.
7. DSP SEND: Use this control to adjust the amount of Digital Signal Processing (DSP) applied to the mic channel.
8. INSERT: Use this jack to connect an external effects device to the amplifier. This is a stereo 1/4 jack, wired as follows:
Tip = Line In (Return - from effect out)
Ring = Line Out (Send - to effect in)
Sleeve = ground
More information on the Insert jack can be found on page 8.
9. INSTRUMENT INPUT: Connect an instru­ment, tape player, CD player, or high imped­ance microphone here by means of a shielded signal cable terminated with a 1/4 connector.
10: GAIN (Active only when the Channel Select switch is depressed): Use this control to adjust the gain for the instrument channel 1 – the lower the setting, the lower the amount of dis­tortion. As this control is rotated clockwise, the distortion increases and the output signal becomes louder.
11: SHAPE (Active only when the Channel Select switch is depressed): Use this control to adjust the tone of the instrument channel 1. Rotating this control counterclockwise enhances mid frequencies; rotating it clockwise enhances the low and high frequencies.
12: LEVEL (Active only when the Channel Select switch is depressed): Use this control to adjust the output level of the instrument channel 1.
13. CHANNEL SELECT: Use this switch to select channel 1 or 2 for the instrument input. When this switch is depressed, the Gain, Shape, and Level controls (#10 – 12) are active. When this switch is in the out position, the Low, Mid, High, and Level controls (#14 – 17) are active. Channel 1 is typically used for electric guitars since the Gain control can be cranked to produce heavily overdriven distortion.
1 2 3 4 5
9 10 11 12 13 14 15 16
6 7
Page 7
CRATE
7
14. LOW (Active only when the Channel Select switch is in the out position): Use this control to adjust the low frequency level for the instru­ment channel 2.
15. MID (Active only when the Channel Select switch is in the out position): Use this control to adjust the mid frequency level for the instru­ment channel 2.
16. HIGH (Active only when the Channel Select switch is in the out position): Use this control to adjust the high frequency level for the instru­ment channel 2.
17. LEVEL (Active only when the Channel Select switch is in the out position): Use this control to adjust the output level of the instrument channel 2.
18. DSP SEND: Use this control to adjust the amount of Digital Signal Processing (DSP) applied to the instrument channel.
19. DSP MODE: Use this control to select the type of Digital Signal Processing (DSP) effect applied to the signal. The nomenclature around the control is as follows:
BYPASS: No effect applied
SLAP: Moderate slapback delay
DELAY: Moderate delay with regeneration
ECHO: Long delay with regeneration
CHORUS: Moderate chorus effect
ROTARY: Simulated rotating speaker effect
CHO/HALL: Chorus combined with large reverb
ROOM: Small reverb effect
HALL: Large reverb effect
20. CD INPUT: Use these jacks to connect the outputs of a CD player or tape player to the amplifier. The output of the CD or tape player may need to be attenuated for a suitable mix with the input channels – see the notes on page 10.
21. FOOTSWITCH: Use this jack to connect a two-button footswitch to the amplifier. The footswitch may be used to remotely control the Instrument channel selection and turn the DSP on and off. The jack is wired as follows:
Tip = Channel Selection
Ring = DSP control
Sleeve = Ground
22. HEADPHONES: Use this jack to connect a pair of stereo headphones for private practice sessions. The internal speakers are discon­nected when headphones are used.
23. LED: When the power switch is on and the battery is fully charged, this LED illuminates yellow. The LED illuminates red when the bat­tery needs recharging.
24. POWER: Use this switch to turn the amplifi­er on (top of the switch depressed) or off (bot­tom of switch depressed).
8
17 18 19 20 21 22 23 24
Page 8
CRATE
8
ABOUT THE INSERT JACK:
The Insert jack (#8) lets you patch external effects into the amplifier just prior to its power amp stage, as shown below. Set the mix controls on the external effects units to full effect (100% wet).
Connecting to the effect’s
insert jack with a stereo cable:
Connecting to the effect with a
stereo-to-mono adapter and cables:
Connecting to the effect with a
stereo-to-mono Y-cable:
THE REAR PANEL:
25. DC CHARGER PLUG, 15VDC: Plug the small round connector of the supplied AC wall adapter into this jack to charge the internal battery. The LED next to the jack glows red when the amp is charging. See page 4 for additional information.
26. DC CIGARETTE LIGHTER ADAPTER, 12 VDC: Plug the small round connector of the optional 12-volt car adapter into this jack to play the amplifier from a vehicle, instead of the internal battery. NEVER connect the supplied 15-volt charger to this jack! See page 4 for additional information.
DC CHARGER
PLUG
LIT WHEN CHARGING
DC CIGARETTE
LIGHTER ADAPTOR
12V DC15V DC
POSITIVE
NEGATIVE
25 26
STANDARD
INSERT
JACK OF
EFFECT
TO
INSERT
JACK
TO
TIP: LINE IN (RETURN)
RING: LINE OUT (SEND)
SLEEVE: GROUND
STEREO 1/4" TO STEREO 1/4" CABLE
(IF EFFECT IS NON-INVERTING)
(IF EFFECT IS INVERTING)
INVERTED
INSERT
JACK OF
EFFECT
TO
INSERT
TO
MONO OUTPUT JACK OF
EFFECT
TO
JACK
TIP
TIP: LINE IN (RETURN)
RING: LINE OUT (SEND)
SLEEVE: GROUND
STP201, 3' STP202, 6' STP203, 9'
DUAL MONO 1/4" TO STEREO 1/4" Y-CABLE
RING
TO MONO INPUT
JACK OF
EFFECT
INSERT
TO
MONO OUTPUT JACK OF
EFFECT
TO
JACK
TIP
TIP: LINE IN (RETURN)
RING: LINE OUT (SEND)
SLEEVE: GROUND
YPP117
DUAL MONO 1/4" TO STEREO 1/4" ADAPTER
RING
MONO 1/4" TO MONO 1/4" CABLES
TO MONO INPUT
JACK OF
EFFECT
Page 9
CRATE
9
SUGGESTED SET
-UPS:
The TX50DE can be used in a variety of different ways, some of which are shown below and on the following page. Use these ideas to fuel your imagination for the setup which best suits your needs.
Idea 1 – Play and sing, with external effects and backup:
Connect a micro­phone to the Low Z jack. Connect an instrument (acoustic or electric gui­tar, keyboard) to the Instrument Input jack. (This high-Z input works with all types of pickups, from Piezo to active types.) Connect a rhythm machine to the CD Input jacks. A two-button footswitch may be used to select Instrument Channel 1 or 2 and to turn the DSP on and off. Connect the external effects device to the Insert jack using one of the methods shown on page 8. (Note that the external effect will be applied equally to both channels, as well as the CD inputs, so use with discretion.)
Idea 2 – Play along:
Connect an instrument (acoustic or electric guitar, keyboard) to the Instrument Input jack. Connect a tape player or CD play­er to either the CD Input jacks or to the Low Z jack of the remaining channel. (See the notes on page 10 for more detailed information.) A pair of stereo headphones may be connected to the Headphones jack for pri­vacy.
LOW Z INPUT
MIC
EFFECTS
(SM1-SP)
RHYTHM MACHINE
INSTRUMENT
INSERT
CD
INPUT
INSTRUMENT
INPUT
FOOT
SWITCH
FOOTSWITCH
(CFP2)
HI Z
INPUT
HEAD
PHONES
CD PLAYER
HEADPHONES
INSTRUMENT
INSTRUMENT
INPUT
TAPE PLAYER
CD
INPUT
Page 10
CRATE
10
SUGGESTED SET
-UPS (continued):
Idea 3 – Sing along: Connect a low impedance microphone to the Low Z jack. Connect a high impedance microphone to the Instrument Input jack. Connect a tape player (for sound tracks and back up music) to the CD Input jacks. A single button footswitch may be used to turn the DSP on and off.
Notes:
When a tape player or CD player is connected to the CD Input jacks,
the output of the player may need to be adjusted by means of its out­put level control (if it has one), or by an external attenuator/preamp.
A tape player or CD player may be connected to either channel instead
of to the CD Input jacks. This provides control of the gain and equaliza­tion of the signal, as well as the application of DSP if desired. In this case, the left and right outputs of the tape or CD player must be summed to create a mono signal, such as shown below.
LOW Z INPUT
MIC 1
MIC 2
TAPE PLAYER
CD
INPUT
INSTRUMENT
INPUT
FOOT
SWITCH
FOOTSWITCH
(CFP1)
LEFT
OUT
TO INPUT JACK
CA9Y DUAL RCA-TO-MONO 1/4" ADAPTER
RIGHT
OUT
Page 11
CRATE
11
SYSTEM BLOCK DIAGRAM:
INSTRUMENT
CHANNEL
MIC
CHANNEL
CD
INPUTS
LOW MID HIGH
GAIN
LEVEL
1
2
CHANNEL
SELECT
LEVEL
DSP
SEND
TONES
LOW MID HIGH
TONES
SHAPE
DC
CHARGER
CHARGING
CIRCUIT
SMART
CHARGER
FUSE
DC
CIGARETTE
LIGHTER
ADAPTER
HEAD
PHONES
SPEAKERS
POWER
AMP
FOOTSWITCH DSP/CH. SELECT
INSERT
FUSE
BATTERY
BATTERY
INDICATOR
CHARGING
INDICATOR
POWER SUPPLY
DSP
SEND
DSP
RETURN
(FOOT
SWITCH
ONLY)
LEVEL
MODE
DSP
Page 12
©2001 SLM Electronics A division of St. Louis Music
1400 Ferguson Avenue St. Louis, MO 63133
P/N 47-099-02 08/01
CRATE
TECHNICAL SPECIFICATIONS
OUTPUT POWER RATING 50W RMS @ 10% THD, 4 ohms, 13.6VDC in
INPUT IMPEDANCE 1M ohm
MAXIMUM SIGNAL ACCEPTED
Mic Low Z 2V peak to peak
Mic Hi Z 12V peak to peak
Instrument 12V peak to peak
GAIN Mic 57dB High Z, 72dB Low Z
Instrument 44dB w/Gain switch out, Ch2
85dB w/Gain switch in, Ch1
SENSITIVITY Mic 3.5mV RMS High Z, 20mV RMS Low Z
Instrument 80mV RMS w/Gain switch out, Ch2
.8mV RMS w/Gain switch in, Ch1
Line In Insert 400mV RMS
EQS, MIC Low ±15dB @ 60Hz
Mid ±15dB @ 600Hz
High ±15dB @ 10kHz
EQS, INSTRUMENT Low 12.5dB range @ 80Hz
Mid 18dB range @ 800Hz
High 18dB range @ 10kHz
Shape Crate proprietary circuit
INSERT JACK Tip Line In
Ring Line Out
Sleeve Ground
SPEAKERS Woofer Crate Custom Design 10, 4 ohm, 100 watt
1.5 voice coil, 16 oz magnet
Tweeter 2 Piezo , 4 ohm, 150 watt network
POWER REQUIREMENTS Internal 12 volt DC power supply
DC adapter for use with 120VAC Optional 12V vehicle lighter adapter
SIZE AND WEIGHT 18-1/2W x 13-1/2H x 12-1/2D; 22 lbs.
The TX50DE is enclosed in a rugged, molded high tech polymer cabinet. Wipe
the enclosure with a damp, lint-free cloth to remove dirt and road film. Never
spray cleaning agents directly onto the enclosure, and stay away from abra-
sive cleansers which could damage the finish.
Crate continually develops new products, as well as improves existing ones. For this reason,
the specifications and information in this manual are subject to change without notice.
www.crateamps.com
Loading...