Crate Amplifiers GFX2200HT User Manual

OWNER’S
MANUAL
GFX2200HT
GUITAR AMPLIFIER
with Channel Tracking &
Digital Signal Processing
Congratulations!
You are now the proud owner of the Crate GFX2200HT guitar amplifier. This rugged amplifier combines outstanding features with serious clean and distorted sounds, with lots of power. An easy to operate DSP (Digital Signal Processing) section lets you dial in a variety of digital effects including reverbs, octave and wah-wahs – with a separate level control. Crate’s unique Channel Tracking feature means that as you switch between channels and gains, the DSP “tracks” the changes – your DSPsettings for each channel are stored and automatically recalled! The supplied three-button footswitch allows you to select channels, change the overdrive gain, and turn the DSP on and off by “remote control.” The front-mounted electronic tuner allows you to tune your instrument any time the amplifier is on.
Like all Crate products, your GFX2200HT is designed by musicians and assembled using only the best components. Extensive testing confirms that this amplifier is the absolute best it can be. Crate’s transferable five-year warranty protects your investment long after many other companies’ warranties have expired.
In order to get the most out of your new amplifier, we strongly urge you to read the information contained in this manual before yo begin playing.
Thank you
for choosing
Contents:
The Digital Signal Processor . . . . . . . . . . . .3
Channel Tracking . . . . . . . . . . . . . . . . . . . .3
The Front Panel . . . . . . . . . . . . . . . . . . . . .4
The Rear Panel . . . . . . . . . . . . . . . . . . . . .5
Some Suggested Settings . . . . . . . . . . . . . .6
System Block Diagram . . . . . . . . . . . . . . . .7
Technical Specifications . . . . . . . .back cover
2
GFX2200HT GUITAR AMPLIFIER
IMPORTANT SAFETY INSTRUCTIONS
READ, FOLLOW, HEED, AND KEEP ALLINSTRUCTIONS AND WARNINGS.
DO NOT OPERATE NEAR ANY HEAT SOURCE AND DO NOTBLOCK ANY VENTILATION OPENINGS ON THIS APPARATUS. FOR PROPER OPERATION, THIS UNITREQUIRES 3”
(75CM) OF WELL VENTILATED SPACE AROUND HEATSINKS AND OTHER AIR FLOW PROVISIONS IN THE CABINET.
DO NOT USE THIS APPARATUS NEAR SPLASHING, FALLING, SPRAYING, OR STANDING LIQUIDS.
CLEAN ONLYWITH LINT-FREE DAMP CLOTH AND DO NOT USE CLEANING AGENTS.
ONLYCONNECT POWER CORD TO APOLARIZED, SAFETY GROUNDED OUTLET WIRED TO CURRENT ELECTRICAL CODES AND COMPATIBLE WITH VOLTAGE, POWER, AND
FREQUENCY REQUIREMENTS STATED ON THE REAR PANEL OF THE APPARATUS.
PROTECT THE POWER CORD FROM DAMAGE DUE TO BEING WALKED ON, PINCHED, OR STRAINED.
UNPLUG THE APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.
ONLYUSE ATTACHMENTS, ACCESSORIES, STANDS, OR BRACKETS SPECIFIED BYTHE MANUFACTURER FOR SAFE OPERATION AND TO AVOID INJURY.
THIS APPARATUS DOES NOT OPERATE NORMALLYAND REQUIRES SERVICE WITH ANY PHYSICALDAMAGE FROM IMPACT OR ANY EXPOSURE TO MOISTURE.
SERVICE MUST BE PERFORMED BYQUALIFIED PERSONNEL.
OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED EXPOSURE TO HIGH SOUND PRESSURE LEVELS CAN CAUSE PERMA-
NENT HEARING IMPAIRMENT OR LOSS. USER CAUTION IS ADVISED AND EAR PROTECTION IS RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
PRECAUCION
RIESGO DE CORRIENTAZO
NO ABRA
PRECAUCION: PARA REDUCIR EL RIESGO DE INCENDIOS O DESCARGAS ELECTRICAS, NO PER­MITA QUE ESTE APARATO QUEDE EXPUESTO A LA LLUVIA O LA HUMEDAD. PARA DISMINUOIR EL RIESGO DE CORRIENTAZO. NO ABRA LA CUBIERTA. NO HAY PIEZAS ADENTRO QUE EL USARIO PUEDO REPARAR DEJE TODO MANTENIMIENTO A LOS TECHNICOS CALIFICADOS.
ATTENTION
RISQUE D'ELECTROCUTION
NE PAS OUVRIR
ATTENTION: PROTÉGEZ CET APPAREIL DE LA PLUIE ET DE L'HUMIDITÉ AFIN D'ÉVITER TOUT RISQUE D'INCENDIE OU D'ÉLECTROCUTION. POUR REDUIRE D'ELECTROCUTION NE PAS ENLEVER LE COUVERCLE. AUCUNE PIECE INTERNE N'EST REPRABLE PAR L'UTILISATEUR. POUR TOUTE REPARATION, S'ADRESSER A UN TECHNICIEN QUALIFIE.
"IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL" “ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES.” "REFERREZ-VOUS AU MANUAL D'UTILISATION"
EXPLANATION OF GRAPHICAL SYMBOLS: EXPLICACION DE SIMBOLOS GRAFICOS: EXPLICATION DES SYMBÔLES GRAPHIQUES:
"DANGEROUS VOLTAGE" “VOLTAJE PELIGROSO” "DANGER HAUTE TENSION"
=
=
3
GFX2200HT GUITAR AMPLIFIER
The Digital Signal Processor:
Crate’s Digital Signal Processing (DSP) offers 16 exciting digital effects, accessible through the DSP
Mode control. The effects are described as follows:
1 REV 1 small room reverb 2 REV 2 medium room reverb 3 REV 3 large room reverb 4 REV 4 concert hall reverb 5 DLY 1 short slapback + small room reverb 6 DLY 2 medium delay + plate reverb 7 DLY 3 long delay + large room reverb 8 FLNG 1 slow deep flange + reverb
9 FLNG 2 flange + reverb + delay 10 CHO 1 slow tremolo chorus + reverb 11 CHO 2 chorus + reverb + delay 12 RTRY simulated rotating speaker effect 13 OCTV DN adds a signal one octave lower than input 14 T-WAH touch sensitive wah-wah effect 15 I-WAH inverse wah-wah effect 16 DBLR simulated second track, slightly out-of-sync
Channel Tracking:
Your Crate GFX2200HT gives you the power of Channel Tracking! Once you select a DSP setting for each channel, Channel Tracking recalls those DSPsettings automatically – without changing the DSP controls! For example:
• Select the Clean channel. Set the DSP Mode to “FLNG 1”
(slow flange + reverb)
• Select the Overdrive channel, Gain 1. Set the DSP Mode to “CHO 1” (slow chorus + reverb) (the setting for the Clean channel is now saved to memory)
• Select the Overdrive channel, Gain 2. Set the DSP Mode to “T-WAH”
(touch wah-wah) (the setting for the
Overdrive channel, Gain 1 is now saved to memory)
• Reselect the Clean channel (the setting for the Overdrive channel, Gain 2 is now saved to memory)
Now when you go back to the Clean channel, even though the DSP Mode was last set to “T-WAH,” Channel Tracking automatically recalls the last setting for the Clean channel – in this example, “FLNG 1.” Change to the Overdrive channel, Gain 1, and “CHO 1” is recalled. Change to the Overdrive channel, Gain 2, and “T-WAH” is recalled. That’s the power of Channel Tracking!
(Note: Even when the power is turned off, Channel Tracking still retains the settings – until you change them!)
RT RY
T-W AH
I- WA H
RE V
CH O 1
CH O 2
LY
BL R
OC TV
N
Use the DSP Mode control to access
any of the 16 built-in digital effects.
Use the level control to mix in the
desired amount of each effect.
LY
REV
BLR
I-WAH
CHO 1
CHO 2
RTRY
OCTV
N
T-W AH
LEVEL
4
GFX2200HT GUITAR AMPLIFIER
. POWER: Use this switch to turn the ampli­er on (top of the switch depressed) and off
bottom of the switch depressed).
. ON LED: This LED illuminates when the mplifier is turned on.
. CHANNEL SELECT FOOTSWITCH: In-
ert the 1/4” stereo plug on the cable attached o the two-button footswitch (supplied) into his jack. This will allow you to use the ootswitch to control channel and gain selec-
on (Channel A- see #18).
. DSP FOOTSWITCH: Insert the 1/4” mono
lug on the cable attached to the two-button ootswitch (supplied) into this jack. This will
llow you to use the footswitch for on/off con­rol of the selected DSP effect.
. DSP MODE: Use this control to select one
f the 16 built-in digital effects. A listing of the
ffects is shown on page 3.
. DSP LEVEL: Use this control to adjust the
mount of the digital effect. In its fully counter
lockwise position the signal will be “dry” without any effect). As you rotate the control
lockwise the amount of effect increases.
CHANNEL B: The Clean Channel:
. BRIGHT: This switch, when depressed,
oosts the upper frequencies of Channel B.
. LEVEL: Use this control to adjust the out-
ut level of Channel B.
. HIGH: Use this control to adjust the high requency level of Channel B.
10. MID: Use this control to adjust the midrange frequency level of Channel B.
11. LOW: Use this control to adjust the low frequency level of Channel B.
12. CHANNEL SELECT: Use this switch to select either channel. With the switch in the out position, Channel B is selected and the adjacent LED illuminates. When the switch is depressed, Channel Ais selected.
CHANNEL A: The Overdrive Channel:
13. LEVEL: Use this control to adjust the out­put level of Channel A.
14. HIGH: Use this control to adjust the high frequency level of Channel A.
15. MID: Use this control to adjust the midrange frequency level of Channel A.
16. LOW: Use this control to adjust the low frequency level of Channel A.
17. GAIN TWO: Use this control to adjust the amount of heavy distortion for Channel A. Gain Two produces more intense distortion than Gain One (#19) and is active when the Gain switch (#18) is depressed.
18. GAIN SELECT: Use this switch to select one of the two gain controls for Channel A (#17, #19). When the switch is depressed, gain two is selected and gain one is disabled. Both of the adjacent LEDs will illuminate. With the switch in the out position, gain one is selected. The right-side LED will illuminate. When a footswitch (#3) is used, this switch is disabled. The LEDs continue to function in the manner described.
19. GAIN ONE: Use this control to adjust the amount of light distortion for Channel A. Gain One produces less intense distortion than Gain Two (#17) and is active when the Gain switch (#18) is in the out position.
20. INPUT: Use this 1/4” jack to connect your guitar to the amplifier by means of a shielded instrument cable.
21. TUNER: The tuner is active whenever the amplifier is turned on. The bottom row of LEDs correspond to the strings of your guitar. The top row of LEDs indicate which way you need to adjust each string for proper tuning. A string is properly tuned whenever the corre­sponding LED on the bottom row and the LED in the center of the top row are illuminated. (See detail below.)
The Front Panel:
RTRY
T-WAH
I-WAH
REV
CHO 1
CHO 2
LY
BLR
OCTV N
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
LY
CHO 1
CHO 2
RTRY
OCTV N
REV
T-WAH
I-WAH
BLR
LEVEL
"FLAT"
"TUNED"
"SHARP"
STRING INDICATORS
5
GFX2200HT GUITAR AMPLIFIER
22. EFFECTS LOOP LINE OUT: When using an external effects processor, con­nect this jack to the input of the effect by means of a shielded signal cable. This jack also doubles as a source for a post-EQ, preamp signal to send your signal to a mix­ing board, recorder, powered monitor or external amplifier.
23. EFFECTS LOOP LINE IN: When using an external effects processor, con­nect this jack to the output of the effect by means of a shielded signal cable. This jack also doubles as a direct connection to the power amp, bypassing the input and pre­amp stages. This is useful for “slaving” a pair of amplifiers together.
24. SPEAKERS: Use these jacks to con­nect the amplifier to your speaker cabi­net(s) using speaker cables with mono 1/4” plugs. These jacks are wired in parallel. Make sure that the combined impedance of your speakers is equal to or greater than 2 ohms! Use the chart below to help deter­mine parallel loads. If in doubt, ask your dealer.
CAB IMP # CABS TOTAL IMP
4 ohms 2 2 ohms 8 ohms 2 4 ohms
8 ohms 4 2 ohms 16 ohms 2 8 ohms 16 ohms 4 4 ohms 16 ohms 8 2 ohms
25. POWER CORD: This grounded power
cord is to be plugged into a grounded power outlet, wired to current electrical codes and compatible with the voltage, power, and frequency requirements stated on the rear panel. Don not attempt to
defeat the safety ground connection.
The Rear Panel:
EFFECTS LOOP
LINE
LINE
OUT
IN
22 23 24 25
SPEAKERS
160 WATTS @ 4 OHMS 220 WATTS @ 2 OHMS
2 OHM MIN. LOAD
6
GFX2200HT GUITAR AMPLIFIER
Some Suggested Settings
RTRY
T-WAH
I-WA H
REV
CHO 1
CHO 2
LY
BLR
OCT V N
RTRY
T-WAH
I-WA H
REV
CHO 1
CHO 2
LY
BLR
OCT V N
RTRY
T-WAH
I-WA H
REV
CHO 1
CHO 2
LY
BLR
OCT V N
RTRY
T-WAH
I-WA H
REV
CHO 1
CHO 2
LY
BLR
OCT V N
RTRY
T-WAH
I-WA H
REV
CHO 1
CHO 2
LY
BLR
OCT V N
OUT
OUT
IN
OUT
IN
IN
AS
NEEDED
"Clean as Glass" "Dirty Blues"
LY
CHO 1
CHO 2
RTRY
OCTV
N
REV
T-WAH
I-WAH
BLR
LY
REV
BLR
I-WAH
CHO 1
T-WAH
CHO 2
RTRY
OCTV N
LEVEL
LEVEL
OUT
"Jazzy Clean" "Grunge Tone"
AS
NEEDED
OUT
IN
"Classic Hard Rock"
LY
CHO 1
CHO 2
RTRY
OCTV N
REV
T-WAH
I-WAH
BLR
LEVEL
OUT
"Heavy Metal"
LY
CHO 1
CHO 2
RTRY
OCTV N
REV
T-WAH
I-WAH
BLR
LEVEL
IN
"Moshin'"
LY
CHO 1
CHO 2
RTRY
OCTV N
REV
T-WAH
I-WAH
BLR
LEVEL
IN
System Block Diagram
7
GFX2200HT GUITAR AMPLIFIER
Declaration Of Conformity
#30, Effective 01-01-2001
Manufacturers Name: SLM Electronics
Production Facility: 11880 Borman Drive, St. Louis, MO 63146, USA Production Facility: 700 Hwy 202 W, Yellville, AR 72687, USA Shipping Facility: 1400 Ferguson Ave., St. Louis, MO 63133, USA Office Facility: 1400 Ferguson Ave., St. Louis, MO 63133, USA
Product Type: Audio Amplifier Complies with Standards:
LVD: 92/31/EEC, 93/68/EEC, & 73/23/EWG Safety: EN60065 EMC: EN55013, EN55020, EN55022, EN61000-3-2,
& EN61000-3-3
Supplementary information provided by your local Sales & Services Office or:
SLM Electronics - R & D Engineering
1901 Congressional Drive, St Louis, MO 63146, USA
Tel.: 314-569-0141, Fax: 314-569-0175
INPUT
INPUT
BUFFER
TUNER
A BC D EF G
DSP
LEVEL
GAIN
ONE
GAIN TWO
LEVEL
CHANNEL B
CHANNEL B
CHANNEL B
MIX
AMP
GAIN
SELECT
LOW
CHANNEL A
CHANNEL A
CHANNEL A
EQ
LOW
HIGH
MID
EQ
HIGH
BRIGHT
MID
EFFECTS
SEND
EFFECTS
RETURN
CHANNEL
SELECT
POWER
AMP
CHANNEL SELECT FOOT SWITCH
DSP FOOT SWITCH
SPEAKER
OUTPUT
SPEAKER
OUTPUT
MODE
GFX2200HT GUITAR AMPLIFIER
Technical Specifications:
Output Power Rating 160 watts RMS, 5% THD, 4 ohm load
220 watts RMS, 5% THD, 2 ohm load
Maximum Input Signal Level Accepted 8 volts peak to peak Input Impedance 470 k ohms Total System Gain Channel B: 54 dB @ 1 kHz, all controls at “10”, Bright off
Channel A: Gain One: 69 dB @ 1 kHz, all controls at “10”
Gain Two: 86 dB @ 1 kHz, all controls at “10”
Channel B Low 25 dB range @ 70 Hz
Mid 14 dB range @ 800 Hz
High 29 dB range @ 10 kHz
Bright 7 dB boost @ 10 kHz
Channel A Low 18 dB range @ 100 Hz
Mid 10 dB range @ 1 kHz
High 17 dB range @ 6 kHz
Input Power Requirements 120VAC, 60HZ, 230VA
100/115VAC, 50/60Hz, 230VA 230VAC, 50/60Hz, 230VA
Cabinet Size and Weight 11.63” H x 30.75” W x 11.63” D; 35 lbs.
The GFX2200HT is covered with a durable black Tolex material; wipe clean with a damp lint-free cloth to remove dirt and road film.
Never spray cleaning agents directly onto the cabinet, and stay away from abrasive cleaners which could damage the finish.
www.crateamps.com
©2002 SLM ELECTRONICS
A DIVISION OF ST. LOUIS MUSIC
1400 FERGUSON AVENUE, ST. LOUIS, MO 63133
47-590-04 • 01-02
CRATEcontinually develops new products, as well as improves existing ones. For this reason,
specifications and information in this manual are subject to change without notice.
Loading...