IMPORTANT SAFETY INSTRUCTIONS:
1.Read, follow and keep these instructions. Heed all warnings.
2.This speaker is capable of producing high sound pressure levels that may cause
permanent hearing damage. User caution is advised and ear protection is recommended during use.
3.This speaker is designed for use on a sturdy, level surface. Whenever stacking
speaker cabinets, do not stack more than two high. Only speaker cabinets which
are equipped with caster cups on their top surfaces are to be used underneath a
cabinet which is equipped with casters.
4.Speaker cables are a tripping hazard and must be routed out of traffic areas and
away from any possible accidental contact.
5.Do not expose this speaker to rain or moisture. Do not place liquid filled containers on this speaker. Clean only with a damp cloth.
6.Repair or service of this speaker should be performed only by qualified personnel.
Your Crate BV412RVB/SVB 4x12 Guitar Cabinet is built from
the finest materials and components available. The cabinet is
carefully constructed from 13 ply Baltic Birch and covered with
extremely tough Tolex®. The cabinet is then loaded with four
Celestion Vintage 30 speakers.
The BV412RVB/SVB comes standard with casters, steel handles, a heavy duty metal grille for ultimate speaker protection,
and a switchable, dual-impedance mono/stereo jackplate. The
BV412RVB features a straight baffle while the BV412SVB features a slanted top baffle.
The BV412RVB/SVB also comes with a 14 gauge speaker
cable to help insure maximum power and full frequency response
from your new cabinet.
For those wishing to use multiple cabinets, the BV412RVB has
caster cups on its top surface to accomodate the casters of a
second cabinet, stacked on top.
BV412RVB/SVBGuitar Enclosure
1
2
3 4
8
The Input/Output Plate:
(1) Impedance Selector Switch:
Use this switch to select 16 ohm
mono operation or 8 ohm stereo/4
ohm mono operation.
(2) Out 1/4” Jack: When using the
cabinet in the mono operating
mode, use this jack to connect the
cabinet to another speaker enclosure of the same impedance.
(3) In/Left 1/4” Jack: When using
the cabinet in the mono operating
mode, use this jack as the cabinet’s
input jack. Connect the output of
your amplifier to this jack by means
of the 14 gauge speaker cable provided.
When using the cabinet in the
stereo operating mode, connect this
jack to the left channel output of
your amplifier.
(4) Right 1/4” Jack: When using
the cabinet in the stereo operating
mode, connect this jack to the right
channel output of your amplifier.
When using the cabinet in the mono
operating mode, this jack is not
used.
Refer to the illustrations to the
right for additional information.
BV412RVB/SVBGuitar Enclosure
4 Ohm Mono Configuration:
16 OHMS
4 OHMS
MONO
8 OHMS
STEREO
16 Ohm Mono Configuration:
16 OHMS
4 OHMS
MONO
OUT
4 OHM16 OHM
OUT IN
MONO
OUT
4 OHM16 OHM
OUT IN
MONO
RIGHTLEFT
Mono Amplifier
BV412RVB/SVB
Input plate
Mono Amplifier
BV412RVB/SVB
Input plate
8 OHMS
STEREO
RIGHTLEFT
Ohm Stereo Configuration:
LEFT OUT RIGHT OUT
Stereo Amplifier
16 OHMS
MONO
4 OHMS
MONO
8 OHMS
STEREO
OUT IN
RIGHTLEFT
BV215RVD
Input plate
BV412RVB/SVBGuitar Enclosure
www.crate.com
©2002 SLM Electronics, Inc. • A Division of St. Louis Music, Inc.
1400 Ferguson Avenue • St. Louis, MO 63133
47-633-04 • 121102
Technical Specifications:
Impedance 4 or 16 ohms Mono, 8 ohms Stereo
RMS Power Rating 240 watts Mono, 120 watts Stereo
Peak Power Handling 480 watts Mono, 240 watts Stereo
Frequency Response 70Hz – 5kHz
Sensitivity 100dB SPL 1 watt/1 meter
Maximum SPL 120dB
Transducers (4) Celestion 12” 16 ohm Vintage 30 speakers
Full Range Inputs (3) 1/4” jacks: Mono In/Out, Stereo Left and Right
Dimensions (H x W x D) 31-1/2” x 30” x 14”
Weight BV412SVB: 106 lbs; BV412RVB: 110 lbs
Specifications subject to change without notice.
Loading...