Page 1
F
XT30
FXT30
Guitar Amplifier with
Digital Signal Processing
User ’s Guide
Page 2
IMPORTANT SAFETY INSTRUCTIONS
• READ, FOLLOW, HEED, AND KEEP ALL INSTRUCTIONS AND WARNINGS.
• DO NOT OPERATE NEAR ANY HEAT SOURCE AND DO NOT BLOCK ANY VENTILATION OPENINGS ON THIS APPARATUS. FOR
PROPER OPERATION, THIS UNITREQUIRES 3” (75mm) OF WELL VENTILATED SPACE AROUND HEATSINKS AND OTHER AIR
FLOW PROVISIONS IN THE CABINET.
• DO NOT USE THIS APPARATUS NEAR SPLASHING, FALLING, SPRAYING, OR STANDING LIQUIDS.
• CLEAN ONLY WITH LINT-FREE DAMP CLOTH AND DO NOT USE CLEANING AGENTS.
• ONLY CONNECT POWER CORD TO A POLARIZED, SAFETY GROUNDED OUTLET WIRED TO CURRENT ELECTRICAL CODES AND
COMPATIBLE WITH VOLTAGE, POWER, AND FREQUENCY REQUIREMENTS STATED ON THE REAR PANEL OF THE APPARATUS.
• PROTECT THE POWER CORD FROM DAMAGE DUE TO BEING WALKED ON, PINCHED, OR STRAINED.
• UNPLUG THE APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.
• ONLY USE ATTACHMENTS, ACCESSORIES, STANDS, OR BRACKETS SPECIFIED BY THE MANUFACTURER FOR
SAFE OPERATION AND TO AVOID INJURY.
• WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK OR FIRE, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
• SERVICE MUST BE PERFORMED BY QUALIFIED PERSONNEL.
• OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED EXPOSURE TO HIGH SOUND
PRESSURE LEVELS CAN CAUSE PERMANENT HEARING IMPAIRMENT OR LOSS. USER CAUTION IS ADVISED AND EAR PROTECTION IS RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
"IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL"
“ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES.”
"REFERREZ-VOUS AU MANUAL D'UTILISATION"
EXPLANATION OF GRAPHICAL SYMBOLS:
EXPLICACION DE SIMBOLOS GRAFICOS:
EXPLICATION DES SYMBÔLES GRAPHIQUES:
"DANGEROUS VOLTAGE"
“VOLTAJE PELIGROSO”
"DANGER HAUTE TENSION"
=
=
PRECAUCION
RIESGO DE CORRIENTAZO
NO ABRA
PRECAUCION: PARA REDUCIR EL RIESGO DE INCENDIOS O DESCARGAS
ELECTRICAS, NO PERMITA QUE ESTE APARATO QUEDE EXPUESTO A LA
LLUVIA O LA HUMEDAD. PARA DISMINUOIR EL RIESGO DE CORRIENTAZO.
NO ABRA LA CUBIERTA. NO HAY PIEZAS ADENTRO QUE EL USARIO PUEDO
REPARAR DEJE TODO MANTENIMIENTO A LOS TECHNICOS CALIFICADOS.
ATTENTION
RISQUE D'ELECTROCUTION
NE PAS OUVRIR
ATTENTION: PROTÉGEZ CET APPAREIL DE LA PLUIE ET DE L'HUMIDITÉ
AFIN D'ÉVITER TOUT RISQUE D'INCENDIE OU D'ÉLECTROCUTION. POUR
REDUIRE D'ELECTROCUTION NE PAS ENLEVER LE COUVERCLE. AUCUNE
PIECE INTERNE N'EST REPRABLE PAR L'UTILISATEUR. POUR TOUTE
REPARATION, S'ADRESSER A UN TECHNICIEN QUALIFIE.
Congratulations!
You are now the proud owner of the Crate FXT30 Guitar Amplifier. This
rugged amplifier features a Clean channel with a three band EQ and Level
control, and a Solo channel with our patented FlexWave technology. An easy
to operate DSP section lets you dial in a variety of digital effects including
reverbs, delays, octave and wah-wahs. AHeadphones jack lets you practice
in private.
Like all Crate products, your FXT amplifier is designed by musicians, and
built using only the best components. Extensive testing confirms that this
amplifier is the absolute best it can be.
In order to get the most out of your new amplifier, we strongly urge you
to read the information contained in this manual before you begin playing.
And thank you
for choosing
CCRRAATTEE
.
F
XT30
Guitar Amp with Digital Signal Processing
Page 3
11
13
The Front Panel:
1: INPUT: Use this 1/4” jack to connect your guitar to
the amplifier by means of a shielded instrument cable.
SOLO CHANNEL: A high gain channel giving you
sounds from a slight edge to serious overdrive.
2: GAIN: Use this control to adjust the amount of distortion for the Solo channel.
3: SHAPE: Use this control to adjust the tone of the
Solo channel.
4: LEVEL: Use this control to adjust the output level
of the Solo channel.
5: SOLO/CLEAN: Use this switch to select the Solo
or Clean channel. With the switch in the out position,
the Clean channel is selected. When the switch is
depressed, the Solo channel is selected.
CLEAN CHANNEL: A normal gain channel designed
to give you crystal clear sounds to medium distortion.
6: VOL: Use this control to adjust the output level of
the Clean channel.
7: LOW: Use this control to adjust the low frequency
level of the clean channel.
8: MID: Use this control to adjust the midrange frequency level of the clean channel.
9: HIGH: Use this control to adjust the high frequency level of the clean channel.
10: DSP LEVEL: Use this control to adjust the level of
the selected digital effect. The DSP effects can be
turned on and off by using a footswitch (#16, rear
panel).
11: DSP MODE: Use this control to select one of the
16 built-in digital effects. The numbers around the
control correspond to the digital effects as listed in the
chart below.
12: HEADPHONES: Use this jack to connect headphones to the amplifier. The internal speaker is disconnected when headphones are used.
CAUTION: To avoid possible damage to your
hearing, do not use headphones for extended
periods of time at extremely loud levels.
13: POWER: Use this switch to turn the amplifier on
(top of the switch depressed) and off (bottom of the
switch depressed). The switch illuminates when the
amplifier is turned on.
The Rear Panel (not shown):
14: EXTENSION SPEAKER: Use this jack to connect
the amplifier to an external speaker. The internal speaker is disconnected when this jack is used. The impedance of the external speaker must be 4 ohms or greater.
WARNING: Do not attempt to use headphones in
the Speaker jack! Permanent hearing damage
could result!
15: FOOTSWITCH: Use this jack to connect the 1/4”
stereo plug on the cable of a two-button footswitch
(such as the Crate CFP2). This allows you to remotely switch between the Clean and Solo channels and
turn the DSP effects on and off.
16: POWER CORD: The grounded power cord should
only be plugged into a grounded power outlet that meets
all applicable electrical codes and is compatible with the
voltage, power, and frequency requirements stated on
the rear panel. Do not attempt to defeat the safety
ground connection.
1 - Small Room Reverb
2 - Medium Room Reverb
3 - Large Room Reverb
4 - Concert Hall Reverb
5 - Short Slapback with Small Room Reverb
6 - Medium Delay with Plate Reverb
7 - Long Delay with Large Room Reverb
8 - Slow Deep Flange with Reverb
9 - Flange with Reverb and Delay
10 - Slow Tremolo Chorus With Reverb
11 - Chorus with Reverb and Delay
12 - Rotating Speaker
13 - Octave Divider
14 - Touch Wah
15 - Inverse Wah
16 - Doubler
The Digital Effects:
F
XT30
Guitar Amp with Digital Signal Processing
1 2 3 4 5 6 7 8 9 101011
121213
Page 4
FXT30 TECHNICAL SPECIFICATIONS:
Output Power Rating >30W RMS @ 5% THD, 4Ω, 120 VAC
Gain Solo Ch 98dB +/-6dB @ 1kHz
Clean Ch 42dB +/-6dB @ 1kHz
Maximum Input Signal Accepted 6 volts peak-to-peak min. @ 1kHz
Tone Controls Low 20dB range @ 80Hz
Mid 12dB range @ 900Hz
High 18dB range @ 10kHz
Speaker Size and Rating 10” Crate Custom Design 4 ohm
Power Requirements 120 VAC, 60Hz, 50VA
100/115VAC, 50/60Hz, 50VA
230VAC, 50/60Hz, 50VA
Size and Weight 15-1/4” H x 17” W x 10” D, 20 lbs.
The FXT30 is covered with a durable Tolex material: wipe it clean with a lint-free cloth.
Never spray cleaning agents onto the cabinet. Avoid abrasive cleansers which would damage the finish.
Crate continually develops new products, as well as improves existing ones. For this reason, the specifications
and information in this manual are subject to change without notice.
www.crateamps.com
©2003 SLM Electronics, a division of St. Louis Music, Inc • 1400 Ferguson Avenue • St. Louis, MO 63133
47-743-02 • 030504
F
XT30
Guitar Amp with Digital Signal Processing
Loading...