CA30D
Acoustic Amplifier
User’s Guide
CA30D Acoustic Amplifier
Table of Contents:
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
The Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connecting to the Insert jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
“Chaining” Amplifiers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
The DSP Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
System Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . back cover
IMPORTANT SAFETY INSTRUCTIONS
• READ, FOLLOW, HEED, AND KEEPALL INSTRUCTIONS AND WARNINGS.
• DO NOT OPERATE NEAR ANY HEAT SOURCE AND DO NOTBLOCK ANY VENTILATION OPENINGS ON THIS APPARATUS. FOR
PROPER OPERATION, THIS UNITREQUIRES 3” (75mm) OF WELL VENTILATED SPACE AROUND HEATSINKS AND OTHER AIR
FLOW PROVISIONS IN THE CABINET.
• DO NOT USE THIS APPARATUS NEAR SPLASHING, FALLING, SPRAYING, OR STANDING LIQUIDS.
• CLEAN ONLY WITH LINT-FREE DAMP CLOTH AND DO NOT USE CLEANING AGENTS.
• ONLY CONNECT POWER CORD TO A POLARIZED, SAFETY GROUNDED OUTLET WIRED TO CURRENT ELECTRICAL CODES AND
COMPATIBLE WITH VOLTAGE, POWER, AND FREQUENCY REQUIREMENTS STATED ON THE REAR PANEL OF THE APPARATUS.
• PROTECT THE POWER CORD FROM DAMAGE DUE TO BEING WALKED ON, PINCHED, OR STRAINED.
• UNPLUG THE APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.
• ONLY USE ATTACHMENTS, ACCESSORIES, STANDS, OR BRACKETS SPECIFIED BYTHE MANUFACTURER FOR
SAFE OPERATION AND TO AVOID INJURY.
• WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK OR FIRE, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
• SERVICE MUST BE PERFORMED BY QUALIFIED PERSONNEL.
• OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED EXPOSURE TO HIGH SOUND
PRESSURE LEVELS CAN CAUSE PERMANENT HEARING IMPAIRMENTOR LOSS. USER CAUTION IS ADVISED AND EAR PROTECTION IS RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
"IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL"
“ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES.”
"REFERREZ-VOUS AU MANUAL D'UTILISATION"
EXPLANATION OF GRAPHICAL SYMBOLS:
EXPLICACION DE SIMBOLOS GRAFICOS:
EXPLICATION DES SYMBÔLES GRAPHIQUES:
"DANGEROUS VOLTAGE"
“VOLTAJE PELIGROSO”
"DANGER HAUTE TENSION"
=
=
PRECAUCION
RIESGO DE CORRIENTAZO
NO ABRA
PRECAUCION: PARA REDUCIR EL RIESGO DE INCENDIOS O DESCARGAS
ELECTRICAS, NO PERMITA QUE ESTE APARATO QUEDE EXPUESTO A LA
LLUVIA O LA HUMEDAD. PARA DISMINUOIR EL RIESGO DE CORRIENTAZO.
NO ABRA LA CUBIERTA. NO HAY PIEZAS ADENTRO QUE EL USARIO PUEDO
REPARAR DEJE TODO MANTENIMIENTO A LOS TECHNICOS CALIFICADOS.
ATTENTION
RISQUE D'ELECTROCUTION
NE PAS OUVRIR
ATTENTION: PROTÉGEZ CET APPAREIL DE LA PLUIE ET DE L'HUMIDITÉ
AFIN D'ÉVITER TOUT RISQUE D'INCENDIE OU D'ÉLECTROCUTION. POUR
REDUIRE D'ELECTROCUTION NE PAS ENLEVER LE COUVERCLE. AUCUNE
PIECE INTERNE N'EST REPRABLE PAR L'UTILISATEUR. POUR TOUTE
REPARATION, S'ADRESSER A UN TECHNICIEN QUALIFIE.
3
CA30D Acoustic Amplifier
Introduction:
Crate Acoustic amplifiers are Made With Pride in the U.S.A.
To keep this amplifier looking its best, avoid abrasive cleansers.
Wipe the cabinet clean using a slightly dampened cloth. Never use
brass cleaners on the hardware since they could damage their protective coatings.
Congratulations!
You are now the proud owner of one of Crate’s latest contributions to
the world of acoustic amplification, the CA30D. This compact amplifier
delivers a strong 30 watts of clear musical power and incorporates two
inputs (each with a gain control), three bands of equalization, plus Crate’s
Contour control for added tonal flexibility. The CA30D features Crate’s
DSP digital reverb and effects, a front panel Insert (effects loop), and a
Line Out jack. An 8” Polypropylene cone coaxial speaker delivers smooth
clear sound with excellent projection and fidelity.
Your CA30D is Musician Made in the U.S.A., using only the best components. Extensive testing at the hands (and ears) of skilled technicians
and musicians insures you that this amplifier is the absolute best it can be.
In order to get the most out of your new amplifier, we strongly urge
you to go over the information contained in this manual before you begin
playing.
And thank you for choosing CRATE.
CA30D Acoustic Amplifier
4
The Front Panel:
1: Power. Use this switch to apply power to
the amplifier: the amp is on when the top
of the switch is depressed, off when the
bottom of the switch is depressed. The
switch illuminates when the amp is on.
2: Line Out. Use this jack to connect a high
impedance, unbalanced line level signal
to a house sound board, a recording console or another amplifier.
3: Insert. Use this jack to add external effects
to the signal. The ring = send (line out),
tip = return (line in), sleeve = ground.
This jack can also be used to “chain” multiple amplifiers together, since connecting
to this jack does not interrupt the signal
going to the amplifier. (See the illustrations on page 5 for more information.)
4: Effects Level. Use this control to adjust
the amount of digital signal processing
applied to the output signal.
5: Effects Mode. Use this control to select the
type of digital signal processing applied to
the output signal. (See the section entitled
“The DSP Section” on page 6 for more information.)
6: High. This serves as the treble control for
both channels. Adjust this control so your
high notes and harmonic overtones are
lively but not overpowering.
7: Contour. Use this control to set the center
point of the mid control. This control
should be set at the frequency which
gives you the most natural midrange
tones.
8: Mid. This serves as the midrange control
for both channels. Adjust this control to
get the best projection and midrange
tones for your instrument. The center
point of the mid control is chosen by the
setting of the contour control (#7).
9: Low. This serves as the bass control for
both channels. Adjust this control to get
the best sounding bass response for your
instrument. Excessive boost of the low
control can cause an unnatural howling
(acoustic feedback from your instrument)
and should be avoided.
11,13:
Input 2, Input 1. The signal output from
your acoustic instrument, tape player,
rhythm machine, high-Z microphone or
other source may be connected to either or
both of these jacks by means of a shielded
signal cable. Each of the input jacks is governed by its corresponding gain control
(#10 for Input 2, #12 for Input 1). The signals from these two jacks are summed
together after their gain stages.
10,12:
Gain 2, Gain 1. Use these controls to set
the input gain level for the corresponding
input jack. These controls set the level of
the input signal and serve as the amplifier’s volume controls.
14: AC Line Cord. (Rear panel, not shown)
The grounded power cord should only be
plugged into a grounded power outlet
that meets all applicable electrical codes
and is compatible with the voltage,
power, and frequency requirements stated on the rear panel. Do not attempt to
defeat the safety ground connection.
1 2 3 6 7 8 94 5 10 11 12 13
5
CA30D Acoustic Amplifier
Connecting to the Insert Jack:
The Insert jack (#3) allows you to patch external effects into the amplifier just prior to
its power amp stage. To connect the effect to the Insert jack use Crate’s STP201, STP202,
or STP203 stereo-to-mono Y-cord, ar an adapter such as Crate’s YPP117 and two shielded
signal cables terminated with 1/4” tip/sleeve connectors as shown below.
D
“Chaining” Amplifiers:
The Line Out jack (#2) on one CA30D can be connected to the Insert jack of another, to
chain the amps together as shown below. (This frees up the Input jacks of the second
amplifier.) Use a shielded cable terminated with 1/4” tip/sleeve connectors as shown.
AMP 2:
AMP 1: AMP 2:
INSERT
AMP 1:
LINE OUT
For short runs,
use Crate's STP201,
STP202 or STP203
adapter to connect an
effects device to the
Insert jack:
TIP = RETURN
RING = SEND
SLEEVE = GROUND
(STP201, 3'
STP202, 6'
STP203, 9')
TIP
to
effect
"OUT"
jack
External Effect
to
effect
"IN"
jack
RING
For longer runs, use
Crate's YPP117 stereoto-mono 1/4" adapter
and two mono 1/4"
signal cables to connect
an effects device to the
Insert jack:
(YPP117)
TIP
External Effect
(1/4"-TO-1/4"
MONO CABLES)
to
effect
effect
"OUT"
jack
TIP = RETURN
RING = SEND
SLEEVE = GROUN
RING
to
"IN"
jack
CA30D Acoustic Amplifier
6
The DSP Section:
The CA30D features Crate’s DSP Digital Signal Processing. Use the
Effects Mode control (#5) to select which type of effect will be applied to
the amp’s output signal. Use the Effects Level control (#4) to adjust the
level of the effect.
The chart below lists the names of the effects as they appear on the amlifier and a description of their settings:
Effect Name Description
Bypass Signal processing is turned off
Slap Short slapback, without regeneration
Delay Medium slapback, with regeneration
Echo Long delay, with regeneration
Chorus Light chorus effect - medium-slow speed
Rotary Simulated “Leslie Speaker” tremolo
Cho/Hall Light chorus, with moderate reverberation
Room Moderate reverberation
Hall Heavy reverberation
4 5
7
CA30D Acoustic Amplifier
System Block Diagram:
Declaration Of Conformity
#33, Effective 01-01-2001
Manufacturer’s Name: SLM Electronics
Production Facility: 1901 Congressional Drive, St. Louis, MO 63146, USA
Production Facility: 700 Hwy 202 W, Yellville, AR 72687, USA
Shipping Facility: 1400 Ferguson Ave., St. Louis, MO 63133, USA
Office Facility: 1400 Ferguson Ave., St. Louis, MO 63133, USA
Product Type: Audio Amplifier
Complies with the following Standards:
Safety: EN60065, E60065, C22.2, UL6500 and/or UL813
EMC: Directive 89/336/EEC, EN55103, EN55013, EN61000,
and/or FCC 47CFR 15B clA
Supplementary information provided by:
SLM Electronics - R & D Engineering
1901 Congressional Drive, St Louis, MO 63146, USA
Tel.: 314-569-0141, Fax: 314-569-0175
CH. 1
INPUT
GAIN
CH. 2
INPUT
GAIN
LOW
MID
CONTOUR
MODE
EFFECTS
LEVEL
HIGH
∑
INSERT
TWEETER
POWER
AMP
WOOFER
LINE
OUT
www.crateamps.com
©2004 SLM Electronics
A Division of St. Louis Music Co.
1400 Ferguson Avenue
St. Louis, MO 63133
47-939-02 • 011404
Output Power Rating: 30 watts RMS @ 1% distortion
High: +/-15dB @ 10kHz
Mid: +/-15dB @ 400–1.2kHz (Contour)
Low: +/-15dB @ 80Hz
Input Impedance: 1.5M ohm
Input Sensitivity: 20mV RMS
Sens. to Line out: 20mV
Max Input Signal: 10v RMS (28v peak to peak)
Insert Jack:
Line Out .7v RMS, Line In .7v RMS
Insert Jack InputImpedance: 44k ohm
Insert Jack Output Impedance: 2.2k ohm
Line Out Output Impedance: 2.2k ohm (Lo-Z), 2.2k ohm (Hi-Z)
Internal Speaker: 8” Poly cone coaxial with dome tweeter;
4 ohms; 50 watts; 1” voice coil
Power Requirements: 120VAC, 60Hz, 50VA
100/115VAC, 50/60Hz, 50VA
230VAC, 50/60Hz, 50VA
Size and Weight: 13”H x 15”W x 12”D, 30 lbs.
Technical Specifications:
Crate continually develops new products, as well as improves existing ones. For this reason,
the specifications and information in this manual are subject to change without notice.
CA30D Acoustic Amplifier
Loading...