Please read this operation guide
prior to using your new enclosure.
IMPORTANT SAFETY INSTRUCTIONS:
1.Read, follow and keep these instructions. Heed all warnings.
2.This speaker is capable of producing high sound pressure levels that may cause
permanent hearing damage. User caution is advised and ear protection is recommended during use.
3.This speaker is designed for use on a sturdy, level surface. Whenever stacking
speaker cabinets, do not stack more than two high. Only speaker cabinets which
are equipped with caster cups on their top surfaces are to be used underneath a
cabinet which is euipped with casters.
4.Speaker cables are a tripping hazard and must be routed out of traffic areas and
away from any possible accidental contact.
5.Do not expose this speaker to rain or moisture. Do not place liquid filled containers on this speaker. Clean only with a damp cloth.
6.Repair or service of this speaker should be performed only by qualified personnel.
Your Crate BV215B Dual 15” Guitar Cabinet is built from the
finest materials and components available. The cabinet is carefully constructed from 13 ply Baltic Birch and covered with
extremely tough Tolex®. The cabinet is then loaded with special
heavy duty speakers which are custom designed to accentuate
the fundamental and subharmonic frequencies of the guitar.
The BV215B comes standard with casters, steel handles, a
heavy duty metal grille for ultimate speaker protection, and a
switchable, dual-impedance mono/stereo jackplate.
The BV215B also comes with a 14 gauge speaker cable to
help insure maximum power and low frequencies from your new
cabinet.
For those wishing to use multiple cabinets, the dimensions of
the BV215B have remained the same as the BV412 cabinets
to allow secure stacking and visual continuity.
BV215B Guitar Enclosure
1
2
3 4
8
The Input/Output Plate:
(1) Impedance Selector Switch:
Use this switch to select 16 ohm
mono operation or 8 ohm stereo/4
ohm mono operation.
(2) Out 1/4” Jack: When using the
cabinet in the mono operating
mode, use this jack to connect the
cabinet to another speaker enclosure of the same impedance.
(3) In/Left 1/4” Jack: When using
the cabinet in the mono operating
mode, use this jack as the cabinet’s
input jack. Connect the output of
your amplifier to this jack by means
of the 14 gauge speaker cable provided.
When using the cabinet in the
stereo operating mode, connect this
jack to the left channel output of
your amplifier.
(4) Right 1/4” Jack: When using
the cabinet in the stereo operating
mode, connect this jack to the left
channel output of your amplifier.
When using the cabinet in the mono
operating mode, this jack is not
used.
Refer to the illustrations to the
right for additional information.
BV215B Guitar Enclosure
4 Ohm Mono Configuration:
16 OHMS
MONO
16 Ohm Mono Configuration:
16 OHMS
MONO
4 OHM16 OHM
4 OHMS
MONO
8 OHMS
STEREO
4 OHM16 OHM
4 OHMS
MONO
OUT IN
OUT IN
OUT
OUT
RIGHTLEFT
Mono Amplifier
BV215RVD
Input plate
Mono Amplifier
BV215RVD
Input plate
8 OHMS
STEREO
Ohm Stereo Configuration:
16 OHMS
MONO
4 OHMS
MONO
8 OHMS
STEREO
OUT IN
LEFT OUT RIGHT OUT
RIGHTLEFT
RIGHTLEFT
Stereo Amplifier
BV215RVD
Input plate
BV215B Guitar Enclosure
www.crate.com
©2002 SLM Electronics, Inc. • A Division of St. Louis Music, Inc.
1400 Ferguson Avenue • St. Louis, MO 63133
47-633-01 • 07/02
Technical Specifications:
Impedance 4 or 16 ohms Mono, 8 ohms Stereo
RMS Power Rating 300 watts Mono, 150 watts Stereo
Peak Power Handling 1200 watts Mono, 600 watts Stereo
Frequency Response 40Hz – 2.5kHz
Usable Low Frequency Limit 28Hz
Sensitivity 99dB SPL 1 watt/1 meter
Maximum SPL 120dB
Transducers (2) 15” Custom Design, 8 ohm, 80 oz magnet,
2-1/2” voice coil dia., 150 watts RMS
Full Range Inputs (3) 1/4” jacks: Mono In/Out, Stereo Left and Right
Dimensions (H x W x D) 31-1/2” x 30” x 14”
Weight 115 lbs
Specifications subject to change without notice.
Loading...