Crane EE-3184-4138, 865, 5058 User Manual

Adorable Humidifiers

1 GALLON/ 3.78 LITRE

ULTRASONIC HUMIDIFIER

MODEL # EE-3184-4138, 865, 5058

PLEASE READ AND SAVE ALL INSTRUCTIONS TO ENSURE THE SAFE AND

EFFECTIVE USE OF THIS APPLIANCE.

TABLE OF CONTENTS

Table of Contents, Humidifier Models P. 1

Important Safety Instructions P. 2

General Safety Instructions P. 3

List of Main Parts P. 4

Tech. Specifications, Contents of Packaging

Operation and Use P. 5-7

Maintenance, Disinfecting Water Tank and
Water Basin, General Maintenance and
Cleaning
Trouble Shooting, Service Centre
Information

Warranty Information P. 11

Warranty Card P. 12

P. 5

P. 8-9

P. 10

HUMIDIFIER MODELS

This instruction manual applies to the following items of the Adorable Humidifiers
product range:
Frog
Model#
EE-3191
Cat
Model#
EE-3187
Basketball
Model#
EE-4137
Nursery Yellow
Model#
EE-3189
Specifications may vary on certain models.

For information on all CRANE Humidifiers please visit our website at
www.crane-canada.com

Elephant
Model#
EE-3186
Pig
Model#
EE-4139
Baseball
Model
EE-4138
Nursery Blue
Model#
EE-3189

Penguin
Model#
EE-865
Cow
Model#
EE-4140
Green Apple
Model#
EE-3184
Dragon
Model#
EE-5058

Panda
Model#
EE-3189
Soccer Ball
Model #
EE-3188
Orange
Model#
EE-3185

Dog
Model#
EE-3190
Football
Model#
EE-4136
Nursery Pink
Model#
EE-3189

1

IMPORTANT SAFETY INSTRUCTIONS

INTRODUCTION

Thank you for purchasing our CRANE Ultrasonic Humidifier. Each unit has been
manufactured to ensure safety and reliability. Before using for the first time, please read
the instructions carefully, and keep them for further reference.

WARNING! READ AND SAVE THESE INSTRUCTIONS. Failure to follow all the
instructions listed below may result in electric shock, fire and/or serious personal injury .

1. Do not carry water tank by handle when it is filled with water. It is
advisable to carry filled water tank with two hands.

2. DO NOT operate outdoors; this humidifier is intended for indoor use only.
Always have water in the water tank when operating the unit.

3. Use only clean, cool tap water to fill the tank (filtered or distilled water is
recommended to avoid white dust if tap water is too hard). DO NOT use hot water.

4. Be sure that the filling cap of the tank is firmly tightened. Alw ays have the mist
direction nozzle and the mist chamber in place while the unit is operating. Rotate
the mist direction nozzle so it aims away from children, walls, fu rniture, and
electrical appliances.

5. Use only a 110-120VAC outlet. ALWAYS plug and unplug unit with dry hands.

6. Never operate the unit with a damaged cord or plug.

7. Always place the unit on a smooth, flat, level surface, and away from direct
sunlight. Keep the cord away from heated surfaces and areas where it could be
walked on or tripped over.

8. Unplug the unit when not in use and whenever you clean or move the unit.

9. Do not add medication of any type into the nozzle, base or water tank. Do not
cover any openings on the unit or insert objects into any openings.

10. The unit should not be left unattended in a closed room as the air could become
saturated and leave condensation on walls or furniture. Leave room door partly
open.

11. When cleaning the inside of the unit keep water away from the air outlet / fan vent
(see FIG.3). Only when the unit is off and unplugged, the exterior may be
wiped with a damp cloth, except the electrical controls. Humidifier requires regular
cleaning. Refer to cleaning instructions.

12. Do not tilt or tip the unit or attempt to empty or fill it while it is in operation.

13. Do not use a detergent to clean any parts of the unit that contain water. Always
use a few drops of bleach with water to clean humidifier. Detergent film dissolved
in the water supply can interfere with the output of the unit.

SAVE THESE INSTRUCTIONS!

2

GENERAL SAFETY INSTRUCTIONS
WARNING! Read and understand all instructions. Failure to f ollow all instructions

listed below may result in electric shock, fire or serious personal injury. The warnings,
cautions, and instruction discussed in this instru ction manual cannot cover all possible
conditions and situations that may occur. It must be understood by the operator that
common sense and caution are a factor which cannot be built into this product, but must
be supplied by the operator.

THIS HUMIDIFIER IS NOT A TOY!

Do not let your child play with this appliance. As with any electrical

appliance
operated by an adult only. Children should be supervised to ensure that they do not play
with the humidifier.

, serious injury and electrocution might be possible. This appliance has to be

SAVE ALL INSTRUCTIONS!

CAUTION: A short power supply cord is provided to reduce the risk of personal injury

resulting from becoming entangled in or tripping over a longer cord. Ext ens ion cords are
available from local hardware stores and may be used if care is exercised in their use. If
an extension cord is required, special care and caution is necessary. Also the cord must
be: (1) marked with an electrical rating of 125 V and at least 13 A., 1625 W., and (2)
the cord must be arranged so that it will not drape over the countertop or tabletop
where it can be pulled on by children or tripped over accidentally.

ELECTRIC POWER

If electric circuit is overloaded with other appliances, your appliances may not operate
properly. The appliances should be operated on a separate electrical circuit from other
operating appliances.

POLARIZED PLUG

This appliance has a polarized plug (one blade is wider than the
other). As a safety feature to reduce the risk of electrical shock, this
plug is intended to fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not attempt to defeat this safety
feature.

SAFETY WARNING

Although your appliance is easy to operate, for your safety, the below warnings must be
followed:

1. Do not place the appliance near a heat source.

2. Never leave the appliance unattended while connected to the electrical outlet.

3. To avoid any accidents, never put a hand over a steam/heat vent or cover when the
appliance is in operation.

4. Use the appliance on a stable surface away from water.

5. Do not unplug from the wall socket by pulling on the supply cord.

6. The appliance must be unplugged:

A. Before either filling or emptying
B. Before any cleaning or maintenance
C. After use
D. If it appears to be faulty

THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY.

3

LIST OF MAIN PARTS

(Specifications may vary on certain models.)
Fig. 1 (Central Body)

1. Central Body (water basin)

2. On/Off Switch

3. Power Cord

4. Regulator Control Knob

5. Humidity Output Indication

6. Red/Green Power Light

(shape of Central Body depends on
model #)

Fig. 2 (Top of Water Tank)

7. Vapor Outlet Channel

8. Water Tank Handle

(shape of Tank depends on model #)

Fig. 3 (Water Basin)

9. Nebulizer

10. Vaporization Chamber

11. Fan Vent

12. Valve Opener

13. Water Level Sensor

Fig. 4 (Bottom of Water Tank)

14. Water Tank Valve

15. Water Tank Cap

16. Vapor outlet channel

Fig. 1

Fig. 2

Fig. 3

Fig. 5 (Water Tank Lid)

17. Water Tank Lid

18. Vapor Output Slots

(shape of Water Tank Lid depends on
model #)

Fig. 4

Fig. 5

4

TECHNICAL SPECIFICATIONS:

Rating Voltage 120V
Frequency 60Hz
Power 32W
Water Tank Capacity Approx. 1.0 Gallon / 3.78

Litres

Output Per 24 Hours Approx. 2.1 Gallon / 8

Litres
Run Time Per Tank Min. 11 Hours
Humidifying Capacity Up to 500 sq.ft. / 46 m2
Noise < 36.5 (dB) A

CONTENTS OF PACKAGING

a. Instruction Manual
b. Central Humidifier Body
c. Water Tank
d. Water Tank Lid with Vapor Output Slots

If any of the above items are missing, please contact our service department:
Chemotec
[e-mail]
Tel: [phone] or 1-800-729-6321
(Business hours Mon-Fri 8:30 – 12:00 am & 1:00 - 4:30pm)

OPERATION AND USE
BEFORE EACH USE

CHECK HUMIDIFIER PLACEMENT - Place the Humidifier on an elevated non-metallic

waterproof surface for best performance. This is to help disperse the mist in the air,
and prevent it from being knocked or tipped over.

CHECK WATER LEVEL SENSOR - Make sure that the water level sensor is secured
properly. Refer to “cleaning and maintaining water level sensor” on page 9 for
instructions on how to assemble water level sensor.

CHECK FAN VENT

This fan vent is located on the bottom of
the humidifier. The purpose of the Fan
Vent is to blow the cool mist through the
vapor outlet slots. It is important that
this part is kept clean and free of
obstructions. We recommend checking
the fan vent before using this item (i.e.
lint, paper).

Do not place humidifier on top of a towel,
or a carpeted surface. The fan vent on
the bottom may become blocked, and
overheat the humidifier.

Fan Vent

5

CAUTION:
DO NOT operate the humidifier without water in the water tank.
DO NOT plug or unplug the cord with wet hands; electric shock
could happen, as with any electrical appliance.

ASSEMBLY

1. Lift the water tank off the central body.

2. Turn over the water tank and unscrew the water tank cap

at the bottom of the tank by turning it counterclockwise.
(See Fig. 6)

Fig. 6

3. Fill water tank with cold water; do not fill all the way to

the rim.

(See Fig. 7)

Note: To avoid possible white dust due to hard water it
is recommended to use filtered or distilled water.

DO NOT use hot water. Use cool tap water.
DO NOT add any medication or other additives to the

water.

DO NOT pour water into Vapor Outlet Channel (part 7,

Fig. 2 on page 4)

4. Replace the water tank cap, aligning the threads on the

tank with the threads on the cap, and turn it clockwise.

(See Fig. 8)

Fig. 7

5. Turn the tank over, holding it by the top handle, and

place it on the central body, making sure it fits perfectly.
Place the water tank cap with output slots on top of the
water tank. (see Fig. 9)

Note: Do not attempt to move humidifier while water tank is
placed on the water basin. Doing so may cause leakage of
water. Also do not place humidifier on the floor. Place
humidifier on an elevated surface.

6. Plug the power cord into a wall socket (do not use

extension cord) and turn on the unit. The On/Off switch
is located at the back of the unit.

7. The Power Light will turn on red. In a few seconds it will

switch to green, indicating that enough water is in the
water basin, and mist will start emitting through the

Fig. 8

Fig. 9

Fig. 10

6

openings at water tank lid.

8. Use the humidity output regulator control knob to adjust

the intensity of the mist output. Turning th e knob
clockwise will increase the moisture output, turnin g the
knob counterclockwise with reduce the moisture output.

Note: When at maximum level it is normal to hear a faint dripping sound.

9. To turn the unit off switch the On/Off switch at the back of the unit to the Off

position.

10. When the humidifier runs out of water the power light will turn red, and the mist

output will stop. This is a safety feature to prevent the humidifier from possibly over
heating and damaging the nebulizer. This safety feature uses a water level sensor to
stop the nebulizer once the water level sinks below the required level in the water
basin. Turn the humidifier off and unplug before removing and refilling the water
tank. Please note that the Power Light on the humidifier body will stay on.

The (red) light signal indicates that the humidifier is turned on and needs to
be refilled.

SET THE CORRECT HUMIDITY OUTPUT

Adjust the mist control so that the mist
rises up and gets absorbed by the room
air. Do not turn on too high an output
as the mist cannot be absorbed by the
air and accumulates on the surface
around the humidifier.
If the humidifier is placed near a fan or
air conditioning outlet the mist may be
forced down by the foreign air stream.
Change the location of the humidifier or
reduce the output of the other room
conditioning appliances.

correct wrong

A NOTE ABOUT HUMIDITY

 It is best to keep the humidity level at about 30-50 percent of relative h umidity.
 The comfort level of humidity will vary from room to room and with changing room

conditions.

 In cold weather, windows and even some walls may fog or develop frost from

excessive indoor humidity. If this occurs, reduce the mist intensity setting to avoid
damage from condensed water dripping on windowsills.

 Too much humidity in the room may allow moisture to accumulate on surfaces where

bacteria and fungi can grow. Moisture that gathers may also damage furniture and
walls, especially wallpaper.

 To eliminate excessive humidity, especially in small rooms, leave the room door open

and adjust the mist intensity control setting.

7

MAINTENANCE

CAUTION:

Always be sure that the humidifier is unplugged and switched OFF before cleaning or
attempting to store the item.

DO NOT leave water in water tank or water basin when unit is not in use as it may
result in the build up of mineral deposits and bacteria t hat can inhibit the output
efficiency of the humidifier. PLEASE NOTE that if water remains in the water tank for
more than a day or two, bacterial growth is possible. ALWAYS use fresh cool water
when using unit.

NOTE: When removing water tank, water may accumulate under vapor lid and on the

bottom of the water tank. It is recommended to have a dry cloth ready to dry wet
surfaces.

CLEANING THE WATER TANK AND WATER BASIN

1. Fill water tank with add a few capfuls of our odourless Crane Humidifier Cleaner
and mix with water allowing the solution to stand for several minutes. Rinse
thoroughly with clean water before use. For heavily soiled surfaces apply the
cleaner and let it soak for a longer period of time. (If Crane Humidifier Cleaner is
unavailable, you can use white vinegar. Rinse the water basin with cool water
repeatedly until the vinegar smell is gone.)

2. Dry with a clean cloth or paper towel.

3. Wipe the water basin with a soft cloth dampened in the cleaner and water
solution. Rinse the water basin with cool water. DO NOT IMMERSE WATER BASIN
IN WATER.

4. Wipe all exteriors surfaces of the base with a soft, dry cloth. Do not immerse the
base in water or use water to clean the base. As with any electrical appliance, an
electric shock may result or the humidifier may be damaged.

NOTE: Please read the label on the Cleaner label before using.

GENERAL MAINTENANCE AND CLEANING

Before any cleaning operation, switch the humidifier off and unplug it.

1. Always unplug the unit before cleaning.

2. The humidifier must be drained and cleaned before storing.

3. Once unplugged the exterior of the unit may be cleaned by wiping with a soft dry
cloth. Caution: The ON/OFF switch must be thoroughly dry before unit is again
plugged into power source.

4. There may be some lime deposits in the nebulizer, particular in areas with hard
water. Overcome this drawback by cleaning the nebulizer with our odourless Crane
Humidifier Cleaner (if Crane Humidifier Cleaner is unavailable, you can use white
vinegar. Rinse with cool water repeatedly until the vinegar smell is gone.) on a soft
cloth regularly, as follows:

A. Dampen a cloth with the cleaner and wipe the nebulizer gently, until the lime

deposits disappear completely.
B. Rub down gently with a dry cloth and remove remains of humidity.
C. Do not rub the nebulizer with solid objects.
D. Do not use any other humidifier cleaner or harsh chemical as this may result

in possible damage to your appliance and void your warranty.

8

5. When cleaning the water basin do not place the nebulizer directly under the water
tap.

6. Never immerse the unit in water or let water enter the fan vent (see figure 3) or
any other openings.

7. It is normal for water to be in the water basin. However water must not get inside
the central body. If this should happen, take the humidifier to an authorized service
center before using it again.

8. Clean the inside of the water tank at least once a week, as stated above.

NOTE: The water level sensor is made of three key parts. When cleaning DO NOT

MISPLACE these parts and MAKE SURE that you assemble these three parts correctly
after cleaning and before operating humidifier. They are as follows:

Plastic Cap – this part has 4 flat tabs coming out from the bottom and is placed on top
of a plastic Pin
Water Float - a small round part resembling a “life saver” candy located underneath
the Plastic Cap
Pin – plastic pin that secures water float and Plastic cap

To clean the water float unscrew the plastic cap from the pin. Remove the water float
and clean by wiping the parts with a soft damp cloth. Replace the parts by first putting
the water float onto the pin and re-screwing the plastic cap onto pin.

STORING

Allow the humidifier to dry completely before storing. Store the humidifier in a dry
location. Do not place any heavy items on top of humidifier during st orage as this may
result in possible damage of the appliance. Always check the plug before use to assure
metal items have not become attached.

STORING YOUR HUMIDIFIER

 Save the box for off-season storage.
 Make sure the tank, water basin and water tank cap are thoroughly dry before

storing.

 If water is left in the unit during storage, it may evaporate completely and leave

deposits that can prevent the unit from operating properly.

 Leave the water tank refill cap loose to prevent the water cap and gasket from

sticking together. This will prolong the life of the gasket.

9

TROUBLE SHOOTING

CAUTION: DO NOT attempt to repair the motor or nebulizer yourself. If the
humidifier continues to not operate please call our service center (see toll free
number below).

Problem Solution

Humidifier Light is staying red and not
turning green

Humidifier is working than stops:

If humidifier does not work at all:

If there is a strange odor:
The power light is green but there is no

mist being emitted:

White dust appears and settles outside the
humidifier:

 Ensure that water level sensor is

assembled properly.

 Clean water float
 Call service center and request

replacement water float

 Ensure it is properly plugged into a

power outlet.

 Check that the switch is in the ON

position.

 If Power On indicator light does not

come on, bring to authorized service
station.

 Clean the tank as stated on Page 8.

 Check that there is water in the tank.
 Check for possible lime deposits on the

water level sensor or the nebulizer (see
page 8 and 9).

 Make sure that nothing blocks the

vapor output slots.

 Check that the fan vent on bottom of

humidifier is not blocked.

 Empty the humidifier and rinse the

water basin with cool tap water and
allow to dry for 15 to 30 min.

 Area tap water may have too many

minerals, change to filtered or distilled
water or use a Crane demineralization
filter cartridge (sold separately)

SERVICE CENTER

If you have any question in regards to the operation of this appliance or are in need of a
spare part please contact our service center:

Chemotec
Tel: [phone] or 1-800-729-6321
[e-mail]
(Business hours Mon-Fri 8:30 – 12:00 am & 1:00 - 4:30pm)

ENVIRONMENTAL PROTECTION

If the appliance should no longer work at all, please make sure that it is disposed in an
environmentally friendly way, by handin g it into a public collection point. Please do not
put it with your household waste.

10

LIMITED WARRANTY

Thank you for purchasing a top quality Crane product. This Ultrasonic Humidifier
was tested and meets our stringent quality standards. This product is warranted
to be free from manufacturing defects in original materials, including original
parts, and workmanship for 1 year with proof of purchase.

The warranty is void if the defect is due to accidental damage, misuse, abuse,
neglect, improper repair or alteration by unauthorized persons or failure to follow
operation instructions provided with the product. This warranty does not apply to
commercial use.

The warranty is non-transferable and applies only to the original purchase and
does not extend to subsequent owners of the product. Liability under this
warranty is limited to repair, replacement or refund. In no event shall liability
exceed the purchase price paid by the purchaser of the product. Under no
circumstances shall there be liability for any loss, direct, indirect, incidental,
special or consequential damage arising out of in connection with use of this
product. This warranty is valid only in Canada. This Warranty gives you specific
legal rights. However you may have other rights that vary from state to state.
Some states do not allow limitation on implied warranties or exclusion of
consequential damages therefore these restrictions may not apply to you.
In case you find this product to be defective please proceed as follows:
A. within 90 days of purchase : return the product to your retailer for a refund
B. After 90 days and within the warranty period: send the product (freight

prepaid) to our service center. To avoid transport damages please send the
product in the original packaging. In return you will receive your repaired
item, a new product or a refund at the service center’s discretion.

Please fill out the Warranty Card and send it together with the product and
purchase receipt

To arrange pick-up of the defective item please contact our service center:
Chemotec

Tel: [phone] or 1-800-729-6321
[e-mail]
(Business hours Mon-Fri 8:30 – 12:00 am & 1:00 - 4:30pm)

WARRANTY INFORMATION

11

WARRANTY CARD

Ultrasonic Humidifier

In case you find this product to be defective please proceed as follows:
A. within 90 days of purchase : return the product to your retailer for a

refund

B. After 90 days and within the warranty period: send the product

(freight prepaid) to our service center. To avoid transport damages
please send the product in the original packaging. In return you will
receive your repaired item, a new product or a refund at the service
center’s discretion.

This Ultrasonic Humidifier was tested and meets our stringent quality
standards. This product is warranted to be free from manufacturing
defects in original materials, including original parts, and workmanship
for 1 year with proof of purchase.

Please fill in your details below and send it together with the product and
purchase receipt. Please read the Limited Warranty conditions mentioned
in this instruction manual.

Customer Name

Street

City

Province

Postal Code

Model #

WARRANTY CARD

Purchase Date

Description of Defect :

PLEASE DETACH THIS SECTION AND RETURN IT WITH YOUR PRODUCT

Service Center Address:
Chemotec

Tel: [phone] or 1-800-729-6321
[e-mail]
(Business hours Mon-Fri 8:30 – 12:00 am & 1:00 - 4:30pm)
8820 Place Ray Lawson,
Anjou, Qc, Canada H1J 1Z2

12