Craig CHT913 User Manual
1. Insert the small plug from the supplied USB
Connection cable to the Mini USB Pod on
the Right of unit.
2. Insert the big plug from the supplied USB
Connection cable to the USB Port on the
supplied AC/USB Adaptor
3. Insert the AC/USB Adaptor to wall outlet
having AC 100-240V~ , 50/60Hz.
NOTE: This AC/USB Adaptor is intended to be correctly orientated in a vertical or
floor mount position.
1. POWER ON/OFF switch
2. button
3. VOL (Volume) + button
4. VOL (Volume) - button
5. USB port (For DC IN)
6. LINE IN jack
AC/USB Adaptor
6
1
4
5
2
1. button
2. button
3. VOL(Volume) - button
4. VOL(Volume) + button
6
5. (Skip Backward) button
6. (Skip Forward) button
3
In fist time use, slide the insulation film from the battery door and discard it as the figure on right:
BATTERY PRECAUTIONS
Follow these precautions when using a battery in this device:
1. Use only the size and type of battery specified.
2. Be sure to follow the correct polarity when installing the battery as indicated in the battery
compartment A reversed battery may cause damage to the device.
3. If the battery in the device is consumed or the device is not to be used for a long period of time.
remove the batteries to prevent damage or injury from possible battery leakage.
4. Do not try to recharge the battery not intended to be recharged; it can overheat and rupture
5. The batteries shall not be exposed to excessive heat such as sunshine. fire or the like
6. Clean the battery contacts and also those of the device prior to battery installation
7. Do not mix different types of batteries together (e.g Alkaline and Carbon-zinc) or old batteries
with fresh ones
8. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed. it
can cause severe internal burn in just 2 hours and can lead to death Keep new and used
batteries away from children. If the battery compartment does not close securely. stop using
the product and keep it away from children. If you think batteries might have been swallowed
or placed inside any parl of the body. seek immediate medical attention
NOTES:
● When there is an obstacle between the unit and the
transmitter, the transmitter may not operate.
● When direct sunlight, an incandescent lamp,
fluorescent lamp or any other strong light shines on
the REMOTE SENSOR of the unit, the remote
operation may be unstable.
Approx.12 feet
1. Connect the Headphone/Earphone; AUX out; Line out jacks
from the external audio player (such like MP3 player;
Discman . . . etc) to the LINE IN jacks on the unit by the
supplied Line In connection cable as the figure on right :
2. Slide the POWER ON/OFF Switch of the unit to ON
position to power on the unit. The STANDBY Indicator
will turn on.
3. Press the button on the unit or Remote Control to turn
the unit ON from standby mode. The STANDBY indicator
will blink. Press again to turn to STANDBY mode.
Note: If unplug the Line In Connection Cable from the Line
In Jack. The unit will turn to BT mode automatically
and the color of STANDBY Indicator will turn to blue.
4. Press the VOL +/- buttons to adjust volume levels (When
the volume level turned to maximum or minimum, two shot
tones will be heard from speaker).
5. Press the button on the Remote Control to mute the
sound temporary, press again to resume.
6. When finished listening, press the button to turn off
(standby mode) the unit.
NOTE: To saving the electric power, unplug the AC/USB Adaptor from wall outlet if
long period of time will not use.
Pairing:
1. Make sure the Line In Connection Cable is Unplug from the LINE IN jack.
2. Slide the POWER ON/OFF Switch of the unit to ON position to power on the unit. The STANDBY
Indicator will turn on.
3. Press the button on the unit or Remote Control to turn the unit ON from standby mode. The BT
Indicator (Blue) will light and blink.
Notes:
~ When the external BT Device searched the unit, our model number “CHT 913” will appear on
the display of external BT Device.
~ Pairing code “0000” may need to enter.
Normal operation after paired:
1. Turn on the BT function of the external BT Device.
2. Power on the unit and enter to BT mode as previous procedures.
3. Wait a few seconds unit the unit paired to the external BT Device automatically. (The BT Indicator
will stop blinking).
4. Plays the music in the connected BT Device as usual.
5. During playback:
~ Press the button on the Remote Control to pause; press again to resume normal playback.
~ Press and release the VOL +/- buttons on the unit or / buttons on the Remote Control to
skip tracks.
~ Press and hold the VOL +/- buttons on the unit or press the VOL +/- buttons on the Remote
Control to adjust volume level. (When the volume level turned to maximum or minimum, two
shot tones will be heard from speaker).
The button cell was consumed, replace by new one.
(Included, Already installed)
1.5A,)
Connection Cable
Connection cable (For Charging Only)
USB adapter
DC 5V, 1.5A Through MINI USB Port
Maximum 7.5W
0.4A;
LIMITED WARRANTY
Craig warrants this product to be free from manufacturing defects in material and
workmanship under normal use for a period of 90 days from date of purchase. If service
is required, please return the product to the store where it was purchased for exchange;
or, pack the unit in the original packing material with all accessories if applicable, a copy
of your sales receipt and a Cashier’s check or Money Order for $7.00 (to cover shipping
and handling costs) payable to Craig Electronics Inc. For consumers in Canada, please
make sure that the cashier check or money order is redeemable through a U.S. bank.
Ship your product freight pre-paid. Your unit will be repaired, replaced or if the unit can
not be repaired or replaced, a refund will be forwarded to you within four weeks of receipt
of your unit. Please ship your unit to:
Craig Electronics Inc.
1160 NW 163 Drive
Miami, Fl 33169
This warranty is void if the product has been: a) Used in a commercial application or
rental. b) Damaged through misuse, negligence, or abuse. c) Modified or repaired by
anyone other than an authorized Craig service center. d) Damaged because it is
improperly connected to any other equipment.
Note: This warranty does not cover: a) Ordinary adjustments as outlined in the Owner’s
Manual which can be performed by the customer. b) Damage to equipment not properly
connected to the product. c) Any cost incurred in shipping the product for repair. d)
Damage to the product not used in the USA.
This warranty is not transferable and only applies to the original purchase. Any implied
warranties, including the warranty of merchantability, are limited in duration to the period
of this expressed warranty and no warranty whether expressed or implied shall apply to
the product thereafter.
Under no circumstance shall Craig be liable for any loss or consequential damage arising
out of the use of this product. This warranty gives specific legal rights. However, you may
have other rights which may vary from state to state. Some states do not allow limitations
on implied warranties or exclusion of consequential damage. Therefore, these
restrictions may not apply to you.
To Obtain Service on your Product
email:service@craigelectronics.com
Printed in China CHT913_WC_E0FG1_B0US
Loading...