Craig CHT823 Owner's Manual

LED ON/OFF

5. (Play/Pause) -- LED ON/OFF Button

Standby On/Off Button

LOCATION OF CONTROLS

BT Mode:
BT (Bluetooth) pairing:

First time use or re-pairing the unit to a new BT Device, pair as follows:

1. Connect the supplier AC/DC Adaptor to the unit and wall outlet as previously instructed. The Red
Indicator on the top of unit will illuminate.

2. Press and holding the Button on the top of unit to turn on the unit from standby mode. The
color of the Red Indicator will turn to Blue and blink.

3. Power on the external BT Device and enter to BT searching mode. Start pairing following the on
screen instructions from the external BT Device. After paired, the Blue Indicator will stop blinking.

4. If pairing is complete you may now play music with your external BT Device.

5. During playback:
　　 Press the ლ—LED ON/OFF Button on the top of unit to pause, press again to resume normal
playback.
　　　 Press and holding the —LED ON/OFF Button to turn off the Decorative Lights, press and
holding again to turn it on again.

Press the orButtons repeatedly to adjust volume level as desired.
　　 Press the or Buttons repeatedly to skip tracks.
　　 If AUX (IN) with connection, press the Button to turn the playback mode to AUX mode, press

again to turn back to BT mode.

6. When finished listening, press and holding the Button until the color of the Blue Indicator turn to
Red to turn the unit to standby mode.

Notes:

1. If long period of time not in use, unplug the AC/DC Adapter from wall outlet for energy saving.

2. When the external BT Device searched the unit, our model number “CHT823” will appear on the
display of external BT Device.

3. If while pairing you are asked for a code please try "0000" or "1234".

Normal operation after pairing:

1. Power on the external BT Device and enter to BT mode.

2. Power on the unit and enter to BT mode as previously instructed. The color of Red Indicator on the
top of unit will turn to Blue and blink.

3. Wait a few seconds until the unit is automatically paired to the external BT Device, the Blue Indicator
will stop blinking.

4. After pairing is complete you may now play music with your external BT Device.

AUX (IN) MODE:

To listen from an external Audio Player such as a MP3 Player, Discman …etc.

1. Connect one end of the supplied Audio Connection Cable to the AUX Out/Line Out/Phone Jack on
the external Audio Player.

2. Connect the other end of the cable to the AUX (In) Jack on the top of unit as the illustrated below:

ACCESSORIES

Check the following before requesting service:

Can’t power
on

Built-in battery drained Recharge the built-in

battery as page 4

No sound or
sound weak

Volume of the unit was set to
minimum position

Volume level of the paired/connected
device is in low level

Volume level too high Reduce the volume level

by press the ლ Button

Reduce the volume level
of the paired/connected device

Pair the external BT device to
the unit as page 6

Place the external BT device
close to the unit

Volume level of the paired/connected
device too high

The external BT device had NOT paired
to the unit

The external BT device too far from
the unit

Rise the volume level
of the paired/connected
device

Increase the volume
level by press the ლ
Button

Volume level
too high

BT not
functioning

SYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTION

Owner's Manual

TROUBLESHOOTING

3. Power on the connected external player and plays the music as usual.

4. Power on the unit as previously instructed. The unit will enter to AUX (In) mode automatically. (If the
unit had not automatically to enter to AUX mode, press the Button to enter.)

5. During playback:
　　 Press the —LED ON/OFF Button on the top of unit to pause, press again to resume normal
playback.
　　 Press and holding the ლ—LED ON/OFF Button to turn off the Decorative Lights, press and
holding again to turn it on again.
　　　　Press the orButtons repeatedly to adjust volume level as desired.

6. When finished listening, press and holding the Button until the color of the Blue Indicator turn to
Red to turn the unit to standby mode.

Warning6tatement

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.

Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction.

