Craftsman ETT3212H Owner’s Manual

Owner's Manual

LECTRBC

Model No. ETT3012H

CAUTION:

Read and follow all safety rules and operating

instructions before first use of this product.

., Safety Rules s Operation

m Maintenance

Troubleshooting

a Parts m Espa_ot

Save this manual for future reference.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website: www_sears.com/craftsman

FULl ONE YEAR WARRANTY

If tills product fails due to a defect in matedal or workmanship within

o_e year from the date of purchase, return it to your nearest Sears store or Craftsman outlet, and it ",,,'illbe replaced free o[ charge,

If this product is used for commercia! purposes, this warranty applies

for only 90 days from the date of purchase, This warra+n[y gives you specif_c iegal rights, and you may also have

other rights which vary from stale to state, Sears, Roebuck and Co., Dept. 8t7 WA, Hoffman Estates, IL 60178

,_b,,_. WARNING: Read and understand

ali instructions, Failure to follow all inslructions i_sted below may result in

eteclric shock, fire and/or +serious personal injury. SAVE THESE INSTRUCTIONS.

" Keep work area dean and well-lit,

Cluttered benches and dark areas invite accidents.,

,, Avoid e_ectrica! hazards, fire hazards, or

damage to the tool, use proper circuit protection, Your nailer is wired at the faclory for !20V operalion. Connect to a

I20V, I5A branch circL_it and use a 15A

time delay fuse or circui:l breaker. To avoid shock or fire, replace power cord

immediately if it is worn, cut or damaged in any way

, Guard against electrical shock, Be sure

your body does not c_ome in contact with grounded surfaces suci) as pipes,

radiators, ranges, _efdgeralors, etc+

• Avoid dangerous work area environment, Do not use power tools in

damp or wet locations. Keep work area well lit,, Do not expose power tools to

reign. Do not use power tools in the preser_ce of flammable i[quids or gases

• Keep ch+fdren: away. All visitors should wear safety goggles; or safety glasses

with :side shields and be kept a safe distance flora work area.

Do not let. visitors come #i contact with tool or extension cords,

• Store idle io_31soWhen not in use, slore too+s in a high, dry loca!.ion that cart be locked. Keep them out of the reach of

children.

• Don*t force the too!, _twil_ do the job better and safer if used at the rate for

which it was desfgned,

• Use the right toot. Do not use a focal for a pu_rpose it was not intended. For

examplle, do not force a small Io0i or attachment to do the job of a heavy-

duty tool,

• Always wear safety goggles or safety glasses with side shields when using

power tooIs+ Also use a face mask or

dust mask if the job is dusty,

• Don*! abuse tool power cord. Never

carry Ihe tool by the cord or yank the cord to disconnect it from the wall, Keep the cord away from heat, oil, and! sharp edges.

, Secure work. Whenever possible, use

clamps or a vise to hold Ihe work It's safer than using your hands and it frees

both hands to use the tool:.

• Don't overreach, Keep proper footing and balance; make sure your footing is

stable+

• Keep toot wel! maintained Follow instructions for lubricating and changing

accessories When applicable, keep tool sharp and clean Inspect cord frequently and have damaged parts repaired by a Sears service center. Keep tool handle and housing clean, dry and free of

grease and oil Never use strong solvents or petroleum-based products

to clean tool

• Disconnect tool when not in use, before

servicing and when loading or changing accessorie&

• Avoid unintentional starting, Never carry

tool with your finger on the switch

• Stay alert Watch what you are doing

and use common sense Do not operate tool when you are tired or under the

influence of drugs, alcohol, or medication.

- Check damaged parts Berore using tool, check that all parts will operate

correctly and will perform as designed. Any damaged parts should be repaired

or replaced by a Sears service center or other qualified service facility. Also, check for misalignment, binding, and broken parts Check that the switch works properly and do not use the tool

if the switch does not turn the tool on and off.

. Replacement parts. When servicing, use

only identical replacement parts ordered from a Sears service center or other

qualified service facility

• Wear hearing protection during extended periods of operation.

,& WARNING: Always wear eye

protection. Any Power Tool can throw foreign objects into the eyes which could

cause permanent eye damage ALWAYS wear safety Goggles (not glasses) that

comply with ANSI safety standard Z87_1.. Everyday glasses have only impact-resistant lenses., ,they ARE NOT safety glasses.

Safety Goggles are available at Sears. NOTE: Glasses or goggles not in

compliance with ANSIZ87..1 could seriously hurt you when they break.

,_k WARNING: Do not aim nailer or shoot

brad nails at a person or animal. Released

brad nails can cause severe injuries.

,, Use only the brad nails indicated in this

manual, Use of accessories that are not designed for this tool could result in

personal injury andlor damage to the tool,

• Do not touch metal parts of tool during operation, Hold only plastic handle or housing,

• Keep tacking speed at one brad nail every two seconds.

• Nailer should be used only for the purposes outlined in this manual, It is

designed for use on wood Do not use on hard surfaces like rock, concrete, etco

personal injury or damage to the tool

could result

• Special caution must be taken when nailing for possible penetration of nails

through the wood into other objects° Use

correct size nails

• When using this tool in high locations,

ALWAYS make sure there is no one

below that could be injured ALWAYS be sure you have a firm footing when using

this tool

• Always hold too! firmly

• Never connect tool to a DC power

source..

• Regular' cleaning, inspection and maintenance is necessary,

• During operation, the nailer may feel warm to the touch. This is normal.

However, if the nailer starts to feel hot,

discontinue use until the unit cools down.

SAVE THESE SAFETY INSTRUCTIONS

GUIDEUNES FOR EXTENSEON CORDS

• When operating a power tool outside, use. an outdoor extension cord marked

"W.#7' or "W". These cords are rated for outdoor use and reduce the risk of

electric shock_

•' Be sure your extension cord is pro.party

MINIMUMGAU.. . GE FOR EXTENSION CORDS .(AWG:} ......

Ampere Ratin_.

More Than No_ More Than

0 6 6 10

_0 12

25" 18

wired, and in good etec!rica! condi[ion_.

A1ways replace a dam:aged exlension cord or have it repai_ed by a qualified

person before using it.. Pro.tact your _×tension cords from sharp

objecls, excessive heat and damp or wet areas.

ToOth of Cord tr_ Feet.

50' t60' 150'

!6 I:6 14

I:6 "_4 12

!6 t4 12

A WARNING: To avoid electrical

hazards, fire hazards, or damage to.lhe tool, use proper cimuil protedion. Your nailer is wired at the fact,ory for 120V operatbn, Connect, to a I20'4, i5A circuit

and use a 15A t,ime delay fuse or circuil breaker. If the power cord is worn or cut, or

damaged in any way, have it replaced immedialeiy,

DOUBLE INSULATED

This nailer !_as a plug that looks like tf_e one shown in Figure A.

The nailer is double insulated _ for additional user protection, All exposed!

m,e_al parts are is,slated from the inLerrJal metal motor components v_lh protective

_r_sulation.

,_WARNiNG: To avoid injury, when servicing use only identical replacement ports.

,_ WARNING; Double insulation does not take !l_e place of normal safety

precaulions when operating {his tool..

• Do not use power I[oo[s irt wet or damp areas or expose them to rain Tl_is 1ool is

intended for indoor use only.

GROUNDING INSTRUCTIONS tn the m,,ent of a maifunction or breakdown,

grounding the pa[h of leas_ resistance for electric, current and reduces the risk of

electric shock, This tool is eqt_i:pped with an electric cord that has a

FigLJreA

POLARIZED grounding plug i[1). The plug t_UST

be plugged into a

matcNng outlet (2) thai

i !'_i', i

;'i 'Jl ,_i

is properly installed _nd grounded in .accordance will) all Locaf codes and ordinances.

Do not modify Ihe plug provided. If' it will not fit lhe outlet, ]lave l;he proper outle! ins{ailed by a quafified elecldcian,

CAUTION: tn all cases, make certain fl_e receptacle in question is properly groundc4,.

If you are not sure_ have a certified; electrician check the receptacle.

A WARNING: To avoid electrocution:

Use only iden[ical replacement, paris when se_vidng a tool with double

insulalion. Servicing should be performed by a qualified technician

SAVE THESE SAFETY _NSTRUCTtONS

SPECIFICATIONS

FEATURES

Input voltage: 120V AC, 50-60 Hz,,

7 Amps

Variable Impact Force provides a great convenience for any task, whether fixing

thin PVC sheet or nailing fine concave

Application: 18 gauge, universal

T-brad nails

beading. Works with hard or soft woods.

• Uses 5 different lengths of T-brads for various projects,

Range: Five lengths: 5/'8", 3f4",

1", I,,3!16", 1,-t[4"

Firing speed: Avg. 30 nailslminute

Loading capacity: 100 nails

BRAD NAi L-TAi3LE-

- Operation speed at 30 nails per minute permits users to complete projects

quickly.

• Transparent magazine cover for checking and re-loading of nails,

......... i]L

Sears 18 gauge Stock No, Inches MM Application for:

****_ 5/8 16 Picture frames, cabinet making, .............................................

27216 3t4 20 27215 I 25 27214 t-3f16 30

***** 1-1_ 32

interior dec,orations, ceiling tiles, baseboards, display assembly, door and window trim, wood furrtiture buildlngtrepair

and more,

1. Trigger switch

2, Power switch 3, Force selector knob

4, Nail magazine 5, Tacking mouth

6. Housing cap

7. Housing

8. Safety"lock pin

9. Loading lever I0. Power cord

+ 11 hidden pages