Craftsman 919.769060, D25852 User Manual
Owner’s Manual
5.5 Horsepower
2400 PSI
2.2 GPM
PRESSURE WASHER
• Safety Guidelines
• Assembly
• Operation
• Maintenance
• Storage
• Troubleshooting
• Repair Parts
• Español
Model No.
919.769060
CAUTION: Read the Safety Guidelines
and All Instructions Carefully Before
Operating.
D25852 Rev. 1 9/10/04
Sears, Roebuck and Co., Hoffman Estates, IL 60170 U.S.A.
Visit our Craftsman website: www.sears.com/craftsman
2- ENG
D25852
TABLE OF CONTENTS
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
SPECIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
SAFETY GUIDELINES- DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .3
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . .3-7
BOX CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-14
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-17
STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-19
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-21
REPAIR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-37
HOW TO ORDER REPAIR PARTS . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARRANTY
FULL ONE YEAR WARRANTY ON CRAFTSMAN HIGH PRESSURE WASHER
For one year from the date of purchase, when this Craftsman High Pressure
Washer is maintained and operated according to the instructions in the owner’s
manual, Sears will repair, free of charge, any defect in material and workmanship.
If your Craftsman Pressure Washer is used for commercial or rental purposes,
this warranty applies only for 90 days from the date of purchase.
FULL TWO YEAR WARRANTY ON CRAFTSMAN ENGINE
For two years from the date of purchase, when this Craftsman engine is
maintained and operated according to the instructions in the owner’s manual,
Sears will repair, free of charge, any defect in material and workmanship.
If your Craftsman engine is used for commercial or rental purposes, this warranty
applies only for 90 days from the date of purchase. This warranty does not cover
expendable items such as spark plugs and air filters, which become worn during
normal use.
Repairs necessary because of operator abuse or negligence, including damage
resulting from no water being supplied to pump or failure to maintain the
equipment according to the instructions contained in the owner’s manual, are not
covered under warranty.
WARRANTY SERVICE IS AVAILABLE BY RETURNING THE HIGH PRESSURE
WASHER TO THE NEAREST SEARS SERVICE CENTER THROUGHOUT THE
UNITED STATES. This warranty gives you specific legal rights and you may also
have other rights, which vary from state to state.
Sears, Roebuck and Co., D/817 WA, Hoffman Estates, IL 60179
3- ENG
D25852
used without the
safety alert symbol
indicates a potentially hazardous
situation which, if not avoided, may
result in pr
operty damage.
indicates a
potentially
hazardous situation which, if not
avoided, could
result in death or
serious injury.
This product may not be equipped with a spark arresting muffler. If
the product is not equipped and will be used around flammable
materials, or on land covered with materials such as agricultural crops, forest,
brush, grass, or other similar items, then an approved spark arrester must be
installed and is legally required in the state of California. It is a violation of
California statutes section 130050 and/or sections 4442 and 4443 of the
California Public Resources Code, unless the engine is equipped with a spark
arrester, as defined in section 4442, and maintained in effective working order.
Spark arrester are also required on some U.S. Forest Service land and may also
be legally required under other statutes and ordinances.
Engine exhaust contains chemicals known, in certain quantities, to cause cancer,
birth defects or other reproductive harm.
Read Operator’s Manual. Do not operate equipment until you have
read Operator’s Manual for Safety
, Assembly, Operation, and
Maintenance Instructions
.
This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING
EQUIPMENT PROBLEMS. To help you recognize this information, we use the
symbols below. Please read and understand the manual and pay attention to
these symbols.
SAFETY GUIDELINES - DEFINITIONS
indicates an
imminently
hazardous situation which, if not
avoided, will
result in death or
serious injury.
indicates a
potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury.
SPECIFICATION CHART
Model No. 919-769060
Pressure Washer
Pressure 2400 PSI
Flow Rate 2.2 GPM
Cleaning Units (PSI x GPM) 5280
Engine
RPM 3600
Rated Horsepower 5.5
Spark Plug Gap .030” (0.76mm)
Gasoline Capacity .29 gallons (1.1 liters)
Oil .58 quarts ( .55 liters) capacity SAE 30 weight
4- ENG
D25852
HAZARD
HOW TO PREVENT ITWHAT CAN HAPPEN
RISK TO BREATHING
RISK OF EXPLOSION OR FIRE
• Use of acids, toxic or corrosive chemi-
cals, poisons, insecticides, or any kind of
flammable solvent with this product
could result in serious injury or death.
• Some cleaning fluids contain substances
which could cause injury to skin, eyes, or
lungs.
• Spilled gasoline and it’s vapors can become ignited from cigarette sparks,
electrical arcing, exhaust gases, and hot
engine components such as the muffler.
• Heat will expand fuel in the tank which
could result in spillage and possible fire
explosion.
• Operating the pressure washer in an explosive environment could result in a
fire.
• Materials placed against or near the
pressure washer can interfere with its
proper ventilation features causing
overheating and possible ignition of the
materials.
• Muffler exhaust heat can damage painted surfaces, melt any material sensitive
to heat (such as siding, plastic, rubber,
or vinyl), and damage live plants.
• Improperly stored fuel could lead to accidental ignition. Fuel improperly
secured could get into the hands of
children or other unqualified persons.
• Do not spray flammable liquids
• Shut off engine and allow it to cool
before adding fuel to the tank.
• Use care in filling tank to avoid spilling
fuel. Move pressure washer away from
fueling area before starting engine.
• Keep maximum fuel level ½” below top
of tank to allow for expansion.
• Always keep pressure washer a minimum of four feet away from surfaces
(such as houses, automobiles, or live
plants) that could be damaged from
muffler exhaust heat.
• Store fuel in an OSHA approved container, in a secure location away from
work area.
• Operate and fuel equipment in well ventilated areas free from obstructions.
Equip areas with fire extinguishers suitable for gasoline fires.
• Never operate pressure washer in an
area containing dry brush or weeds.
HAZARD
HOW TO PREVENT ITWHAT CAN HAPPEN
• Operate pressure washer in a well ventilated area. Avoid enclosed areas such
as garages, basements ,etc.
• Never operate unit in a location
occupied by humans or animals.
• Use only cleaning fluids specifically recommended for high pressure washers.
Follow manufacturers
recommendations.Do not use chlorine
bleach or any other corrosive compound
• Breathing exhaust fumes will cause serious injury or death.
IMPORTANT SAFETY INSTRUCTIONS
5- ENG
D25852
RISK OF UNSAFE OPERATION
• If proper starting procedure is not
followed, engine can kickback
causing serious hand and arm injury.
HAZARD
HOW TO PREVENT ITWHAT CAN HAPPEN
• Become familiar with the operation and
controls of the pressure washer.
• Keep operating area clear of all persons,
pets, and obstacles.
• Do not operate the product when
fatigued or under the influence of
alcohol or drugs. Stay alert at all times.
• Never defeat the safety features of this
product.
• Do not operate machine with missing,
broken, or unauthorized parts.
• Never leave wand unattended while unit
is running.
• If engine does not start after two
pulls, squeeze trigger of gun to
relieve pump pressure. Pull starter
cord slowly until resistance is felt.
Then pull cord rapidly to avoid
kickback and prevent hand or arm
injury.
• Unsafe operation of your pressure
washer could lead to serious injury or
death to you or others.
• The spray gun/wand is a powerful cleaning tool that could look like a toy to a
child.
• Keep children away from the pressure
washer at all times.
• Reactive force of spray will cause
gun/wand to move, and could cause the
operator to slip or fall, or misdirect the
spray. Improper control of gun/wand can
result in injuries to self and others.
• Do not overreach or stand on an
unstable support. Grip gun/wand firmly
with both hands. Expect the gun to kick
when triggered.
RISK OF ELECTRICAL SHOCK
• Spray directed at electrical outlets or
switches, or objects connected to an
electrical circuit, could result in a fatal
electrical shock.
• Unplug any electrically operated product
before attempting to clean it. Direct
spray away from electric outlets and
switches.
HAZARD
HOW TO PREVENT ITWHAT CAN HAPPEN
6- ENG
D25852
HOW TO PREVENT ITWHAT CAN HAPPEN
RISK TO FLUID INJECTION
• Your washer operates at fluid pressures
and velocities high enough to penetrate
human and animal flesh, which could
result in amputation or other serious
injury. Leaks caused by loose fittings or
worn or damaged hoses can result in
injection injuries. DO NOT TREAT FLUID
INJECTION AS A SIMPLE CUT! See a
physician immediately!
• Never place hands in front of nozzle.
• Direct spray away from self and others.
• Make sure hose and fittings are tightened and in good condition. Never
hold onto the hose or fittings during operation.
• Do not allow hose to contact muffler.
• Never attach or remove wand or hose
fittings while system is pressurized.
• Use only hose and high pressure
accessories rated for pressure higher
than your pressure washer's p.s.i.
HAZARD
• Relieve system pressure before attempting maintenance or disassembly
of equipment.
• To relieve system pressure, shut off
engine, turn off water supply, and pull
gun trigger until water stops flowing.
HOW TO PREVENT ITWHAT CAN HAPPEN
HAZARD
RISK OF CHEMICAL BURN
• Use of acids, toxic or corrosive chemicals, poisons, insecticides, or any kind
of flammable solvent with this product
could result in serious injury or death.
• Do not use acids, gasoline, kerosene, or
any other flammable materials in this
product. Use only household detergents, cleaners and degreasers
recommended for use in pressure
washers.
• Wear protective clothing to protect eyes
and skin from contact with sprayed
materials.
• Do not use chlorine bleach or any other
corrosive compound.
7- ENG
D25852
HOW TO PREVENT ITWHAT CAN HAPPEN
HAZARD
RISK OF HOT SURFACES
• Contact with hot surfaces, such as
engines exhaust components, could
result in serious burn.
• During operation, touch only the control
surfaces of the pressure washer. Keep
children away from the pressure washer
at all times. They may not be able to
recognize the hazards of this product.
HOW TO PREVENT ITWHAT CAN HAPPEN
HAZARD
• Fuel or oil can leak or spill and could
result in fire or breathing hazard, serious
injury or death can result. Fuel or oil
leaks will damage carpet, paint or other
surfaces in vehicles or trailers.
• If pressure washer is equipped with a
fuel shut-off valve, turn the valve to the
off position before transporting to avoid
fuel leaks. If pressure washer is not
equipped with a fuel shut-off valve, drain
the fuel from tank before transporting.
Only transport fuel in an OSHA approved
container. Always place pressure washer
on a protective mat when transporting to
protect against damage to vehicle from
leaks. Remove pressure washer from
vehicle immediately upon arrival at your
destination.
RISK OF INJURY AND PROPERTY
DAMAGE WHEN TRANSPORTING
OR STORING
The powerful spray from your pressure washer is capable of
causing damage to surfaces such as wood, glass, automobile paint,
auto striping and trim, and delicate objects such as flowers and shrubs. Before
spraying, check the item to be cleaned to assure yourself that it is strong enough to
resist damage from the force of the spray. Avoid the use of the concentrated spray
stream except for very strong surfaces like concrete and steel.
Operating without flow of water will result in equipment damage. Operating the
pressure washer with water supply shutoff will void your warranty. You should never
run this pressure washer for more than 2 minutes without pulling the trigger to allow
cool water to enter the pump and the heated (recirculated) water to exit.
8- ENG
D25852
2. Connect wand to gun. Tighten
securely.
3. Attach high pressure hose to gun.
Tighten securely.
ASSEMBLY
1. Place handle assembly onto
frame and connect handle to
frame.
BOX CONTENTS
Handle
Part No. D22302
Bagged Parts
Nozzle Cleaning
Kit
English/
Spanish
Operator’s
Manual
Engine Frame and
Wheel Assembly
High Pressure
Hose
Part No. D22166
Chemical Hose
Part No. H140
Engine Oil
Spray Gun
Part No. 17780
Multi-Reg Wand
Part No. A06122
Accessories Panel Part No. D25081
with Screws Part No. D22901
Knobs
Part No.
16471
Saddle
Bolts Part
No. D23196
Allen Wrench Part No. 16797
Cleaning Tool Part No. NCT001
9- ENG
D25852
5. To Assemble Accessories Panel
a. Remove top screws on
handle assembly.
b. Loosen bottom screws on
handle assembly.
c. Place grooves in accessories
panel assembly onto screws
and slide panel assembly
into place.
d. Place screws (removed
earlier) into the top holes
and secure accessories
panel assembly to handles.
Do not overtighten.
Loosen
Screws
Remove
10- ENG
D25852
PRESSURE WASHER
High Pressure Pump (located
inside the shroud): Increases the
pressure of the water supply.
Engine: Drives the high pressure
pump.
High Pressure Hose: Carries the
pressurized water from the pump to
the gun and wand.
Spray Gun: Connects with wand to
control water flow rate, direction, and
pressure.
Multi-Reg Wand: Has a spray nozzle
which adjust from a pencil stream (0°)
to a wide angle fan spray (40°). The
spray can be adjusted by twisting the
nozzle clockwise and/or
counterclockwise. Also, the high and
low pressure settings can be controlled by moving the nozzle in and
out. See Operation section.
ENGINE
Choke Control: Opens and closes
the choke valve in carburetor.
Throttle Control Lever: Controls
engine speed.
Starter Grip: Pulling starter grip
operates recoil starter to crank
engine.
Fuel Valve Lever: Opens and closes
connection between fuel tank and
carburetor.
Chemical Hose: Allows cleaners or
cleaning solvents to be mixed with
the pressurized water stream. See
How To Siphon Chemicals/Cleaning
Solvents in Operation section of this
manual.
OPERATION
Know Your Pressure Washer
READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING
YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with
the location of various controls and adjustments. Save this manual for future
reference.
High
Pressure
Pump
Engine
High
Pressure
Hose
Spray
Gun
Multi-Reg
Wand
Chemical
Hose
Hand
Grip
Air Filter
Fuel Valve
Lever
Choke
Control
Throttle
Control
11- ENG
D25852
TO ADJUST PRESSURE
The pressure setting is preset at the
factory to achieve optimum pressure
and cleaning. If you need to lower the
pressure, it can be accomplished by
these methods.
1. Back away from the surface to be
cleaned. The further away you
are, the less the pressure will be
on the surface to be cleaned.
2. Reduce the speed of the
gasoline engine (RPM). Slow the
engine down and the water
pressure will go down with it.
DO NOT attempt to
increase pump
pressure. A higher pressure
setting than the factory set
pressure may damage pump.
HOW TO USE
IMPORTANT: Read and understand
how to use the pressure washer
before operating.
TO USE WAND
Your pressure washer is equipped
with a multi-reg wand with both high
and low pressure settings. The high
pressure setting is for cleaning and
rinsing, the low pressure setting is for
applying chemicals or cleaning
solutions to surfaces.
Risk of injection or
injury to person. Do
not direct discharge stream toward
persons, unprotected skin, eyes, or
towards any pets or animals.
Serious injury can occur.
For high pressure operation, pull back
the nozzle of the multi-reg wand as
shown.
PRESSURE WASHER
TERMINOLOGY
NOTE: Become familiar with this
terminology before operating.
PSI: Pounds per Square Inch. The
unit of measure for water pressure.
Also used for air pressure, hydraulic
pressure, etc.
GPM: Gallons Per Minute. The unit
of measure for the flow rate of water
through the pressure washer.
CU: Cleaning Units. GPM multiplied
by PSI.
Bypass Mode: In Bypass Mode, the
pump is recirculating water because
the trigger of the spray gun is not
pulled. If unit is left in bypass mode
for more than two (2) minutes, the
water temperature will rise to a
dangerous level and damage internal
components of the pump.Any
damage to pump due to these causes
will not be covered under warranty.
DO NOT allow your
unit to operate in
bypass mode for more than two
minutes at any time. Overheating
of pump can cause damage to
pump.
Thermal Relief Valve: In an effort to
prevent damage, pumps are equipped
with a thermal relief valve. This valve
will open when the temperature inside
the pump rises too high. This valve
will then release a gush of water in an
effort to lower the temperature inside
the pump. Immediately after this
occurs, the valve will close.The
thermal relief valve is part of the
pump and is not visible
to the user.
Chemical Injection: Feeds cleaning
agents into the pump to mix with the
pressurized water and help in
cleaning.
Water Supply: All pressure washers
must have a source of water. The
minimum requirements for a water
supply are 20 PSI and 5 gallons per
minute.
12- ENG
D25852
The nozzle at the end of the multi-reg
wand can be rotated to change the
high pressure spray pattern from a
narrow jet to a 40º fan shape, as
shown. Markings have been placed
on the nozzle to help you select the
spray pattern.
For low pressure operation, extend
the nozzle of the multi-reg wand as
shown.
40º fan spray
narrow jet stream
TO SIPHON
CHEMICALS/CLEANING
SOLVENTS
Siphoning chemicals or cleaning
solvents is a low pressure operation.
NOTE: Use only soaps and
chemicals designed for pressure
washer use. Do not use bleach.
1. Press chemical hose onto
barbed fitting located near high
pressure hose connection of
pump as shown.
2. Place other end of chemical hose
with filter on it into container
holding chemical/cleaning
solution.
3. Set multi-reg nozzle to low
pressure setting, see How To
Use Wand paragraph in this
section.
4. After use of chemical, siphon
clean water through chemical
hose to rinse it and pump clean.
Chemicals which remain in pump
can damage it. Damage to pump
due to chemicals will not be
covered under warranty.
NOTE: Chemicals and soap will not
siphon when wand is in the high
pressure setting.
Barb fitting
TO SHUT DOWN
IMPORTANT: Read and understand
how to shut down the pressure
washer before operating.
1. If you have siphoned chemicals,
siphon a bucket of clean water
through the chemical hose.
NOTE: Failure to do so will
cause damage to the pump.
2. Turn engine off by placing the
throttle control in the OFF
position.
NOTE: NEVER turn the water off
with the engine running.
3. Turn the fuel valve to the OFF
position if engine will not be
restarted soon.
4. Turn water source off.
5. Pull trigger on spray gun to
relieve any water pressure in
hose or spray gun.
6. See Storage section in this
manual for proper storage
procedures.
13- ENG
D25852
3. Verify the filter screen is in water
inlet of pump, as shown.
4. Connect high pressure hose to
pump outlet.
5. Connect water source to pump
inlet.
NOTE: Water source must provide
a minimum of 5 gallons per minute
at 20 p.s.i.
6. If you are applying a chemical or
cleaning solution, See How To
Siphon Chemicals/Cleaning
Solvents in Operation section of
this manual.
7. Turn water source on.
NOTE: Make sure water supply is
turned on.
Water
Source
High
Pressure
Hose
Filter Screen
BEFORE STARTING
Read and understand all Important
Safety Instructions in the front of
this manual and the following
Cautions and Warnings before
starting the pressure washer.
• Never fill fuel tank completely.
Fill tank to 1/2" below bottom
of filler neck to provide space
for fuel expansion. Wipe any
fuel spillage from engine and
equipment before starting
engine.
• Never fill fuel tank indoors.
Never fill fuel tank when engine
is running or hot. Do not
smoke when filling fuel tank.
• Never run engine indoors or in
enclosed, poorly ventilated
areas. Engine exhaust contains carbon monoxide, an
odorless and deadly gas.
• Never turn water supply off
while pressure washer engine
is running or damage to pump
will result.
• DO NOT use hot water, use
cold water only.
• DO NOT stop spraying water
for more than two minutes at a
time.
1. Add fresh high quality unleaded
gasoline with a pump octane
rating of 86 or higher. Do not
overfill. Wipe up spilled fuel
before starting the engine.
2. Remove filler cap/dipstick and
add engine oil (supplied) to
engine. NOTE: There will be a
slight amount of oil in the engine
from factory testing. Always
check oil level before each startup.
Filler cap/dipstick
14- ENG
D25852
necessary.
If the engine does
not start after two
pulls, pull the trigger to relieve the
pressure.
11. If the choke was used to start
the engine, move the choke lever
to the OFF position.
12. Depress trigger on gun to start
water flow. Release trigger to
stop water flow.
13. Adjust nozzle spray for the task
being performed. See How To
Use Wand instructions in this
section.
DO NOT let hoses
come in contact
with very hot engine muffler during
or immediately after use of your
pressure washer.
MAINTENANCE
WHEN PERFORMING MAINTENANCE, YOU MAY BE
EXPOSED TO HOT SURFACES, WATER PRESSURE,
MOVING PARTS, OR FIRE RESULTING IN DEATH. BEFORE PERFORMING
ANY MAINTENANCE OR REPAIR, DISCONNECT SPARK PLUG WIRE, LET
ENGINE COOL AND RELEASE ALL WATER PRESSURE. THE ENGINE
CONTAINS FLAMMABLE FUEL. DO NOT SMOKE OR WORK NEAR OPEN
FLAMES WHILE PERFORMING MAINTENANCE.
To ensure efficient operation and longer life of your pressure washer, a routine
maintenance schedule should be prepared and followed. If the pressure washer
is used in unusual conditions, such as high-temperatures or dusty conditions,
more frequent maintenance checks will be required.
8. Turn fuel valve to the ON
position, 1/4 turn
counterclockwise.
9. Move the choke control lever to
the CHOKE ON position and
the throttle control to the FAST
position. NOTE: No choke is
needed to start a warm engine.
10. Pull starter grip slowly until you
feel resistance, then pull briskly.
Return starter grip gently. Pull
rope with a rapid full arm stroke.
Let rope rewind slowly. Repeat if
Fuel Valve Knob
Choke
Control
Throttle
Control
Loading...