Craftsman CMCBL760 Instruction Manual

INSTRUCTION MANUAL | GUIDE D’UTILISATION | MANUAL DE INSTRUCTIONES

60V Max* Handheld Blower
Souffleur portable 60 V max*
Soplador Portátil 60 V Máx*

CMCBL760

IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.
POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.
SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.

1-888-331-4569 WWW.CRAFTSMAN.COM

final page size: 8.5 x 5.5 in CRAFTSMAN

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 10

Español (traducido de las instrucciones originales) 20

ENGLISH

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk
of personal injury or property damage.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or



seriousinjury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or



seriousinjury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or



moderateinjury.

(Used without word) Indicates a safety related message.



NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in

propertydamage.

Fig. A

1

Variable speed trigger

2

Cruise control lever

3

Main handle

4

Tube

5

Battery

4

COMPONENTS

2 1

WARNING: Read all safety warnings



and all instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/
or seriousinjury.

WARNING: Never modify the product or



any part of it. Damage or personal injury couldresult.

3

5

WARNING: To reduce the risk of injury,

read the instructionmanual.

If you have any questions or comments about this or
any product, call CRAFTSMAN toll free at:
1-888-331-4569.

1

ENGLISH

60V Max* Handheld Blower
CMCBL760

IMPORTANT SAFETY
INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE

USING THIS APPLIANCE

When using this appliance, basic safety precautions should
always be followed including the following:

WARNING: To reduce the risk of fire,



electric shock and injury:

• Do not leave the appliance when connected
to power source. Remove the battery pack when
not in use and before servicing.

• Do not use on wet surfaces. Do not expose to
rain. Storeindoors.

• Do not allow appliance to be used as a toy.
Close attention is necessary when used by or
nearchildren.

• Use this appliance ONLY as described in the
manual. Use only recommended attachments.

• Do not use this appliance if it is showing
signs of malfunction in any way. If the
appliance is not working correctly, has been
dropped, damaged, left outdoors, or dropped into
water, return it to a service center.

• Do not handle the appliance with wethands.

• Do not put any objects into the openings of
the appliance. Do not use the appliance with
any opening blocked; keep free of dust, lint, hair
and anything else that may reduce air flow.

• Keep hair, loose clothing, fingers, and all body
parts away from the openings and moving parts.

• Turn off all controls before disconnecting from
power source.

• Use extra care when cleaning on stairs.

SAVE THESE INSTRUCTIONS

Additional Safety Instructions

WARNING: When using an electric



appliance, basic safety precautions should always
be followed to reduce risk of fire, electric shock, and
personal injury, including the following.

WARNING: Read all safety warnings and



all instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.

To Reduce Risk of Injury:

• Avoid accidental starting. Turn off all controls before

removing the battery pack. Be sure switch is in the locked
or off position before inserting battery pack. Carrying units
with your finger on the switch or inserting the battery pack
into a unit with the switch on invites accidents.

• Avoid dangerous environmental conditions – Do not

use electric units in damp or wet locations. Don’t use the
unit in the rain.

• Use safety equipment. Always wear eye protection,

filter mask if operation is dusty, non-skid safety shoes,
hard hat, or hearing protection must be used for
appropriateconditions.

• Use the right unit – Do not use this unit for any job

except that for which it is intended.

• Inspect the area before using the unit. Remove all debris

and hard objects such as rocks, glass, wire, etc. that can
ricochet, be thrown, or otherwise cause injury or damage
during operation.

• Keep children, bystanders and animals away from

the work area a minimum of 30 feet (10 meters) when
starting or operating the unit.

• Maintain unit with care. Keep unit clean for best

and safest performance. Follow instructions for
propermaintenance.

• Stay alert - Watch what you are doing. Use common

sense. Do not operate unit when you are tired.

• Do not place outlet of blower near eyes or ears

whenoperating.

• Do not attempt to clear clogs from unit without first

removing the battery.

• Do not immerse any part of the unit in liquid.

• Do not use unit if switch does not turn it on or
off. A unit that cannot be controlled with the switch is
dangerous and must be repaired.

• Do not allow debris to be ingested into blower intake.

• Do not point unit discharge at self or bystanders.

• Do not use to blow explosive dust, or in areas where
air contains explosive dust such as coal, grain, or other
combustible material.

• Do not attempt to repair the blower. To assure
product safety and reliability, repairs, maintenance,
and adjustments should be performed by authorized
servicecenters.

• Do not operate blower in a gaseous or explosive
atmosphere. Motors in these units normally spark, and
the sparks might ignite fumes.

• Do not overreach. Keep proper footing and balance at
all times.

• Never leave blower running unattended. Turn
poweroff.

• Remove the battery pack before connecting

thetube.

2

• Store idle units. When not in use, the unit should be

stored in a dry, high or locked-up place - out of reach
ofchildren.

• Instructions for compatible batteries and chargers
are included for reference in this manual. Read all
instruction manuals included with your battery pack or
charger. Read all cautionary markings on the charger and
battery pack.

• Disconnect the battery pack from the blower before

making any adjustments, changing accessories,
servicing, moving or storing the unit. Such

preventative safety measures reduce the risk of starting the
appliance accidentally.

SAVE THESE INSTRUCTIONS

Additional Safety Information

WARNING: ALWAYS use safety glasses.



Everyday eyeglasses are NOT safety glasses. Also use
face or dust mask if operation is dusty. ALWAYS WEAR
CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.

WARNING: Some dust contains



chemicals known to State of California to cause
cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:

• compounds in fertilizers,

• compounds in insecticides, herbicides
andpesticides,

• arsenic and chromium from chemically treated
lumber.

To reduce your exposure to these chemicals, wear
approved safety equipment such as dust masks
that are specially designed to filter out microscopic
particles.

• Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmfulchemicals.

WARNING: Use of this tool can generate



and/or disperse dust, which may cause serious
and permanent respiratory or other injury. Always
use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles
away from face andbody.

WARNING: Always wear proper



personal hearing protection that conforms

ENGLISH

to ANSI S12.6 (S3.19) during use. Under some
conditions and duration of use, noise from this
product may contribute to hearingloss.

CAUTION: When not in use, place tool



on its side on a stable surface where it will not
cause a tripping or falling hazard. Some tools with

a large battery pack will stand upright but may be
easily knocked over.

• Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be caught
in movingparts.

The label on your tool may include the following symbols. The
symbols and their definitions are asfollows:

V ......................... volts

Hz ....................... hertz

min ..................... minutes

or DC ......direct current

...................... Class I Construction

(grounded)

…/min .............. per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM .................... strokes per minute

OPM .................... oscillations per

minute

A ......................... amperes

W ........................ watts

or AC ........... alternating current

or AC/DC .... alternating or

direct current

...................... Class II

Construction

(double insulated)

no ....................... no load speed

n ......................... rated speed

...................... earthing terminal

..................... safety alert symbol

..................... visible radiation

..................... avoid staring at

light

..................... wear respiratory

protection

..................... wear eye

protection

..................... wear hearing

protection

..................... read all

documentation

IPXX .................... IP symbol

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read the
safety instructions below and then follow charging
proceduresoutlined. When ordering replacement battery
packs, be sure to include the catalog number andvoltage.

READ ALL INSTRUCTIONS

Important Safety Instructions for All
Battery Packs

WARNING: Read all safety warnings,



instructions, and cautionary markings for the
battery pack, charger and product. Failure to
follow the warnings and instructions may result
in electric shock, fire and/or serious injury.

• Do not charge or use the battery pack in explosive
atmospheres, such as in the presence of flammable

3

ENGLISH

liquids, gases or dust. Inserting or removing the battery
pack from the charger may ignite the dust orfumes.

• When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,
nails, screws, or other small metal objects, that can
make a connection from one terminal to another.

Shorting the battery terminals together may cause burns
or a fire.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into
a non-compatible charger as battery pack may
rupture causing serious personal injury. Consult

the chart at the end of this manual for compatibility of
batteries andchargers.

• Charge the battery packs only in CRAFTSMAN chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or
exceed 104°F (40°C) (such as outside sheds or metal
buildings in summer). For best life store battery packs in
a cool, drylocation.
NOTE: Do not store the battery packs in a tool with
the trigger switch locked on. Never tape the trigger
switch in the ONposition.

• Do not incinerate the battery pack even if it is
severely damaged or is completely worn out. The

battery pack can explode in a fire. Toxic fumes and
materials are created when lithium-ion battery packs
areburned.

• If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open
eye for 15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte is composed of
a mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If symptoms
persist, seek medicalattention.

WARNING: Burn hazard. Battery liquid



may be flammable if exposed to spark orflame.

WARNING: Fire hazard. Never attempt



to open the battery pack for any reason. If the battery
pack case is cracked or damaged, do not insert into
the charger. Do not crush, drop or damage the battery
pack. Do not use a battery pack or charger that has
received a sharp blow, been dropped, run over or
damaged in any way (e.g., pierced with a nail, hit
with a hammer, stepped on). Damaged battery packs
should be returned to the service center forrecycling.

Storage Recommendations

1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully
charged battery pack in a cool dry place out of the
charger for optimal results.

NOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged before use.

Battery Pack Cleaning Instructions

Dirt and grease may be removed from the exterior of the
battery using a cloth or soft non-metallic brush. Do not use
water or any cleaningsolutions.

The RBRC® Seal

The RBRC® (Rechargeable Battery Recycling
Corporation) Seal on the nickel cadmium,
nickel metal hydride or lithium-ion batteries
(or battery packs) indicates that the costs
to recycle these batteries (or battery
packs) at the end of their useful life have already been
paid by CRAFTSMAN. In some areas, it is illegal to place
spent nickel cadmium, nickel metal hydride or lithium-ion
batteries in the trash or municipal solid waste stream and
the Call2Recycle® program provides an environmentally
consciousalternative.

Call 2 Recycle, Inc., in cooperation with CRAFTSMAN and
other battery users, has established the program in the
United States and Canada to facilitate the collection of
spent nickel cadmium, nickel metal hydride or lithium-ion
batteries. Help protect our environment and conserve
natural resources by returning the spent nickel cadmium,
nickel metal hydride or lithium-ion batteries to an
authorized service center or to your local retailer for
recycling. You may also contact your local recycling center
for information on where to drop off the spent battery.

RBRC® is a registered trademark of Call 2 Recycle,Inc.

Transportation

WARNING: Fire hazard. Do not store



or carry the battery pack so that metal objects
can contact exposed battery terminals. For

example, do not place the battery pack in aprons,
pockets, tool boxes, product kit boxes, drawers, etc.,
with loose nails, screws, keys, etc. Transporting

batteries can possibly cause fires if the battery
terminals inadvertently come in contact with
conductive materials such as keys, coins,
hand tools and the like. The US Department of

Transportation Hazardous Material Regulations
(HMR) actually prohibit transporting batteries in
commerce or on airplanes in carry-on baggage
UNLESS they are properly protected from short circuits.
So when transporting individual battery packs, make
sure that the battery terminals are protected and well
insulated from materials that could contact them and
cause a short circuit. NOTE: LI-ion batteries should not
be put in checkedbaggage.

4

Important Safety Instructions for All
Battery Chargers

WARNING: Read all safety warnings,



instructions, and cautionary markings for the
battery pack, charger and product. Failure to
follow the warnings and instructions may result
in electric shock, fire and/or seriousinjury.

• DO NOT attempt to charge the battery pack with
any chargers other than a CRAFTSMAN charger.

CRAFTSMAN charger and battery pack are specifically
designed to worktogether.

• These chargers are not intended for any uses other

than charging CRAFTSMAN rechargeable batteries.

Any other uses may result in risk of fire, electric shock
orelectrocution.

• Do not expose the charger to rain orsnow.

• Pull by the plug rather than the cord when
disconnecting the charger. This will reduce the risk of
damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected

to damage orstress.

• Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size
(AWG or American Wire Gauge) for safety. The
smaller the gauge number of the wire, the greater the
capacity of the cable, that is, 16 gauge has more capacity
than 18gauge. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating.
When using more than one extension to make up the
total length, be sure each individual extension contains at
least the minimum wire size. The following table shows
the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier
gauge. The lower the gauge number, the heavier thecord.

Minimum Gauge for Cord Sets

Volts

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

More

Not

Than

More
Than

0 6 18 16 16 14

6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not Recommended

• Do not place any object on top of the charger or
place the charger on a soft surface that might block

Total Length of Cord in Feet

(meters)

American Wire Gauge

ENGLISH

the ventilation slots and result in excessive internal

heat. Place the charger in a position away from any heat

source. The charger is ventilated through slots in the top
and the bottom of thehousing.

• Do not operate the charger with a damaged cord
orplug–have them replaced immediately.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any
way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an
authorized service center when service or repair is
required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk
of electric shock. Removing the battery pack will not

reduce thisrisk.

• NEVER attempt to connect 2 chargerstogether.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

WARNING: Shock hazard. Do not allow



any liquid to get inside the charger. Electric shock
mayresult.

WARNING: Burn hazard. Do not



submerge the battery pack in any liquid or allow any
liquid to enter the battery pack. Never attempt to
open the battery pack for any reason. If the plastic
housing of the battery pack breaks or cracks, return to
a service center for recycling.

CAUTION: Burn hazard. To reduce the



risk of injury, charge only CRAFTSMAN rechargeable
battery packs. Other types of batteries may
overheat and burst resulting in personal injury and
propertydamage.

CAUTION: Under certain conditions, with



the charger plugged into the power supply, the
charger can be shorted by foreign material. Foreign
materials of a conductive nature, such as, but not
limited to, grinding dust, metal chips, steel wool,
aluminum foil or any buildup of metallic particles
should be kept away from the charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting toclean.

Charging a Battery

NOTE: To ensure maximum performance and life of

lithium-ion battery packs, charge the battery pack fully

before firstuse.

5

ENGLISH

1. Plug the charger into an appropriate outlet before
inserting batterypack.

2. Connect the charger and battery pack, making sure
the battery is fully seated. The (charging) light will
blink continuously indicating that the charging process
hasstarted.

3. The completion of charge will be indicated by the light
remaining ON continuously. The battery pack is fully
charged and may be removed and used at this time or

left in the charger.

NOTE: To remove the battery pack, some chargers require
the battery pack release button to bepressed.

Indicators

Charging

Fully Charged

4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the batterypack.

5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting toclean.

6. Do not freeze or immerse the charger in water or any
otherliquid.

Charger Cleaning Instructions

Hot/Cold Pack Delay

A charger will not charge a faulty battery pack. The charger
refusing to light could indicate a problem with the charger.

NOTE: If the charger refuses to light, take the charger and
battery pack to be tested at an authorized servicecenter.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot
or too cold, it automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery pack has reached an
appropriate temperature. The charger then automatically
switches to the pack charging mode. This feature ensures
maximum battery packlife.

A cold battery pack may charge at a slower rate than a
warm batterypack.

Important Charging Notes

1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature
is between 65°F – 75°F (18° C– 24°C). DO NOT charge
when the battery pack is below +40°F (+4.5°C), or
above +104°F (+40°C). This is important and will
prevent serious damage to the batterypack.

2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulatedtrailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out
the lights;

c. Move the charger and battery pack to a location

where the surrounding air temperature is
approximately 65°F – 75°F (18°C – 24°C);

d. If charging problems persist, take the tool, battery

pack and charger to your local servicecenter.

WARNING: Shock hazard. Disconnect



the charger from the AC outlet before cleaning. Dirt
and grease may be removed from the exterior of the
charger using a cloth or soft non-metallic brush. Do
not use water or any cleaningsolutions.

SAVE THESE

INSTRUCTIONS

FOR FUTURE USE

COMPONENTS (FIG. A)

Intended Use

This cordless handheld blower is designed for household
blowing applications.

DO NOT use under wet conditions or in presence of
flammable liquids orgases.

DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of



serious personal injury, turn unit off and remove
the battery pack before making any adjustments
or removing/installing attachments or
accessories. An accidental start-up can causeinjury.

CAUTION: Ensure the battery is removed



before removing extension attachment or end
attachment. An attachment must be attached to the
housing before use.

Tube Assembly (Fig. A, B)

• To attach the tube

7

rail

on the housing opening with the notch onthe

8

tube

opening. Push the tube into the blower housing

4

to the blower,line up theguide

6

until the lock engages the tube and an audible click
isheard.

• Pull on the tube to ensure it is securely in place.

• To remove the tube, insert a screwdriver into the
unlocking hole
tube out.

Fig.B

9

on both sides of the housing and pull

9

Proper Hand Position (Fig. A, D)

WARNING: To reduce the risk of serious



personal injury, ALWAYS use proper hand position
as shown.

WARNING: To reduce the risk of serious



personal injury, ALWAYS hold securely in anticipation
of a sudden reaction.

Hold the blower with one hand on the main handle

Fig.D

ENGLISH

3

7

8

OPERATION

WARNING: Do not operate blower



without tube securely in place. Never reach down into
housing through tube hole.

WARNING: Always remove the battery



when you leave blower unattended or when storing,
checking, adjusting, cleaning, or working onblower.

Installing and Removing the Battery Pack
(Fig. C)

NOTE: For best results, make sure your battery pack is
fullycharged.

To install the battery pack
battery pack with the rails inside the tool’s handle and slide
it into the handle until the battery pack is firmly seated in
the tool and ensure that it does notdisengage.

To remove the battery pack from the tool, press the release

6

button

and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of thismanual.

Fig.C

5

into the tool handle, align the

6

5

3

Switching On (Fig. A, D, E)

CAUTION: Do not point unit discharge at



self or bystanders.

CAUTION: Always wear safety glasses and



hearing protection. Wear a filter mask if the operation
is dusty. Use of gloves, long pants and substantial
footwear is recommended. Keep long hair and loose
clothing away from openings and moving parts.

To turn the blower on, depress the variable speed trigger
To turn the blower off, release the variable speed trigger.

To lock the blower on, pull back on the cruise control

(2

lever

, as shown in FigureE. The blower runs at higher
speeds as the lever is moved further. The cruise control lever
can also be pulled back to start the blower without needing
to first depress the variable speed trigger.

To turn the blower off when using the speed lock lever,
push the lever toward the front of the blower.

• Hold the blower with one hand as shown in FigureD

and sweep from side to side with the tube
inches above the hard surface. Slowly advance keeping
the accumulated pile of debris in front of you.

4

1

several

.

7

ENGLISH

Fig.E

MAINTENANCE

WARNING: To reduce the risk of



serious personal injury, turn unit off and remove
the battery pack before making any adjustments
or removing/installing attachments or
accessories. An accidental start-up can causeinjury.

Accessories

WARNING: Since accessories, other than



those offered by CRAFTSMAN, have not been tested
with this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be
used with thisproduct.

Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.

Versatrack™ (Fig. F)

2

1

suspend tool on the Versatrack™ Trackwall using the
integral hang hook.

WARNING: The Versatrack™ integral



hang hook is intended to mount the tool onto a
Versatrack™ Trackwall rail. Do not use the integral
hang hook to mount the tool to any other surface.

WARNING: The Versatrack™ integral



hang hook is not a belt hook.

WARNING: When hanging objects on a



Versatrack™ Trackwall rail, adequately space the tools
in order to not exceed 75 lb (35 kg) per linear foot.

WARNING: Before using the tool make



sure that the Versatrack™ integral hang hook is
returned to its original position.

IMPORTANT: Versatrack™ accessories mount compatible
tools securely to the Versatrack™ Trackwallsystem.

1. Turn tool off, remove the battery pack and
removeaccessories.

CAUTION: Any product with exposed



cutting teeth must have them covered securely if it is
to be on theVersatrack™ Trackwall.

2. Flip or pull open the integral hang hook
when locked into position.

3. Mount the integral hang hook to the
Versatrack™Trackwall.

NOTE: Versatrack™ accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.

Fig.F

10

. It clicks

10

WARNING: To reduce the risk of



serious personal injury, turn unit off and remove
the battery pack before making any adjustments
or removing/installing attachments or
accessories. An accidental start-up can causeinjury.

WARNING: To reduce the risk of serious



personal injury, do not use a damaged Versatrack™
integral hang hook or Versatrack™ Trackwall.
A damaged Versatrack™ integral hang hook or
Versatrack™ Trackwall will not support the weight of
the tool.

WARNING: To reduce the risk of serious



personal injury, DO NOT suspend tool overhead or
suspend objects from the integral hang hook. ONLY

8

Cleaning

WARNING: Blow dirt and dust out of all



air vents with clean, dry air at least once a week. To
minimize the risk of eye injury, always wear ANSI Z87.1
approved eye protection when performingthis.

WARNING:Never use solvents or other



harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into aliquid.

Repairs

The charger and battery pack are notserviceable. There are
no serviceable parts inside the charger or battery pack.

WARNING: To assure product



SAFETY and RELIABILITY, repairs, maintenance
and adjustment (including brush inspection and
replacement, when applicable) should be performed
by a CRAFTSMAN factory service center or a
CRAFTSMAN authorized service center. Always use
identical replacementparts.

Register Online

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case
there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of an

insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
SafetyAct.

Register online at www.craftsman.com/registration

Four Year Limited Warranty

CRAFTSMAN will repair or replace, without charge, any
defects due to faulty materials or workmanship for four
years from the date of purchase. This warranty does
not cover part failure due to normal wear or tool abuse.
For further detail of warranty coverage and warranty
repair information, visit www.craftsman.com or call
1-888-331-4569. This warranty does not apply to
accessories or damage caused where repairs have been
made or attempted by others. THIS LIMITED WARRANTY
IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow
limitations on how long an implied warranty lasts or the

ENGLISH

exclusion or limitation of incidental or consequential
damages, so these limitations may not apply to you. This
warranty gives you specific legal rights and you may have
other rights which vary in certain states orprovinces.

NOTE: Battery warranty voided if the battery pack is
tampered with in any way. CRAFTSMAN is not responsible
for any injury caused by tampering and may prosecute
warranty fraud to the fullest extent permitted bylaw.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of
your CRAFTSMAN Power Tool or Nailer for any reason, you
can return it within 90 days from the date of purchase with
a receipt for a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in
the packaging, call the local company or see website for
warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning
labels become illegible or are missing, call 1-888-331-4569
for a freereplacement.

9