Craftsman C950.679630, C950.679631 Operator's Manual

2200 PSI MAX

2.2 GPM MAX

PRESSURE WASHER

Operator’s Manual

Model No. C950.679630

Part No. 310389GS Draft - (06/12/2009)

HOURS: Mon. - Fri. 8 a.m. to 5 p.m. (CT)

PRESSURE WASHER

CUSTOMER HELPLINE

1-800-222-3136

• Safety

• Assembly

• Operation

• Maintenance

• Parts

• Français, p. 30

Sears Canada, Inc.

Visit our Craftsman website: www.sears.ca

AVERTISSEMENT

Avant d’utiliser ce produit, veuillez lire le

manuel et suivre toutes les directives

relatives à la sécurité et à l’utilisation.

WARNING

Before using this product, read this

manual and follow all Safety Rules

and Operating Instructions.

This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101 (Testing and
Rating Performance of Pressure Washers).

Les caractéristiques nominales de ce nettoyeur à haute pression sont conformes à la norme PW101 de la Pressure Washer Manufacturers
Association (PWMA) (Tests et performance nominale des nettoyeurs à haute pression).

Not for

Reproduction

WARRANTY

2

TABLE OF CONTENTS

CRAFTSMAN LIMITED WARRANTY

General: Craftsman products are warranted to be free from defects in materials or workmanship for a specific time period as

set-out below (the “Warranty Period”). Warranties extend to the original purchaser of a Craftsman product only. Purchases
made through an online auction or through any website other than www.sears.ca are excluded. The relevant Warranty Period
commences on the original date of purchase. Within this period, Sears Canada, Inc. will, at its sole option, repair or replace
any products or components which fail in normal use. Such repairs or replacement will be made at no charge to the customer
for parts or labor, provided that the customer shall be responsible for any transportation cost.

Exclusions: This warranty does not cover failures due to normal wear, abuse, misuse, neglect (including but not limited to the
use of stale fuel, dirt, abrasives, moisture, rust, corrosion, or any adverse reaction due to improper storage or use habits),
improper maintenance or failure to follow maintenance guidelines and/or instructions, failure to operate the product in
accordance with the owner’s manual or any additional instructions or information provided at the time of purchase or in
subsequent communications with the original purchaser, accident or unauthorized alterations or repairs made or attempted by
others. Also excluded from warranty coverage – except as provided below - are the following: maintenance, adjustments,
components subject to wear including but not limited to: cosmetic components, belts, blades, blade adapters, bulbs, tires,
filters, guide bars, lubricants, seats, grips, recoil assembly’s, saw chains and bars, trimmer lines and spools, spark plugs,
starter ropers and tines, and discoloration resulting from ultraviolet light. Any product missing the model and/or serial
number identification label will be disqualified from coverage under this warranty.

Repairs: Repairs conducted within the Warranty Period will be warranted until the end of the original Warranty Period.

Disclaimers: THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER

WARRANTIES, WHETHER ORAL OR WRITTEN (OTHER THAN AS STATED HEREIN), AND WHETHER EXPRESS, IMPLIED OR
STATUTORY, INCLUDING BUT NOT LIMITED TO ANY. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY
VARY FROM PROVINCE TO PROVINCE.

IN NO EVENT SHALL SEARS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES,
WHETHER RESULTING FROM THE USE, MISUSE OR INABILITY TO USE THE PRODUCT OR FROM DEFECTS IN THE
PRODUCT. THE EXCLUSIONS IN THIS PARAGRAPH SHALL NOT APPLY IN JURISDICATIONS WHERE APPLICABLE LAW
DOES NOT ALLOW FOR THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. IN SUCH JURISDICTIONS, THIS
PARAGRAPH SHALL NOT APPLY, BUT THE REMAINING PROVISIONS OF THIS DOCUMENT SHALL REMAIN VALID.

Sears retains the exclusive right to repair or replace the product or offer a full refund of the purchase price at its sole
discretion. SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY.

WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

FEATURES AND CONTROLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-19

STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-27

EMISSION CONTROL WARRANTY . . . . . . . . . . . . . . . . . . . . . 28-29

FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-55

HOW TO ORDER PARTS . . . . . . . . . . . . . . . . . . . . . . . . BACK PAGE

© 2009

Not for

Reproduction

3

Customer Responsibilities: In additional to complying with all suggested maintenance guidelines and instructions, customers’
obligations shall include but shall not be limited to: operating the product in accordance with the owner’s manual or any
additional instructions or information provided at the time of purchase or in subsequent communications to the purchaser
from time to time, exhibit reasonable care in the use, operation, maintenance, general upkeep and storage of the product.
Failure to comply with these requirements will void any applicable warranty.

List of Applicable Warranty Periods: The following list contains the applicable Warranty Period for your Craftsman product
and is based on a combination of the type of product or component and the intended and actual use of the product or
component:

1. 90 days: Craftsman products intended for use or actually used for commercial, institutional, professional or income-

producing purposes

2. 2 years: Craftsman riding lawn mowers, yard and garden tractors, walk behind mowers, tillers, brush cutters, snow

blowers, handheld blowers, backpack blowers, hedge trimmers and electrical products for noncommercial,
nonprofessional, non-institutional, or non-income-producing use, except for those components which are part of engine
systems manufactured by third party engine manufacturers for which the purchase has received an separate warranty with
product information supplied at the time of purchase.

3. 1 year: Craftsman pressure washers, power cutters, stump grinders, pole pruners, gas chain saws, electric chain saws,

trimmer attachments, baggers and pole saws for noncommercial, nonprofessional, non-institutional, or non-income­producing use.

4. 90 days: All defective batteries, which will be replaced during this 90-day Warranty Period.

5. 60 days: Additional Warranty Period of 60 days will apply to adjustments and worn products or components BUT DOES

NOT INCLUDE WEAR OR ADJUSTMENTS for products used for commercial, institutional, professional or income­producing purposes. Wear items include but are not limited to: belts, blades, tires, spark plugs, air filters, chains, shear
bolts, skid plates, scraper bars, drift cutters, ropes, tines, collection bags and pulleys.

Service Type: Craftsman product is either Carry-in/Shop service or At Home service. The following list identifies the service
by product type.

Shop Service:

Craftsman walk behind mowers, tillers, brush cutters, handheld blowers, backpack blowers, hedge trimmers, power cutters,
stump grinders, pole pruners, gas chain saws, electric chain saws, trimmer attachments, baggers and pole saws

At Home Service:

Craftsman riding lawn mowers, yard and garden tractors and snow blowers

As the Warranty Period runs from the date of purchase and NOT from the date that a product is delivered, opened, assembled
or first used, please ensure during this time period that your product or component has been assembled and tested for
correction operation regardless of when you intend to actually use it. Claims made after the Warranty Period has expired will
not be honored.

Proof of Purchase/Documentation: Warranty coverage is conditioned upon the original purchaser furnishing Sears Canada or
its authorized third party service provider if applicable, with the original sales receipt or other adequate written proof of the
original purchase date and identification of the product. In the event that the original purchaser is unable to provide a
company of the original sales receipt, Sears Canada Inc. reserves the right to determine in its sole discretion what other
written proof of the original purchase date and identification of the product is acceptable.

SEARS CANADA INC., TORONTO, ONTARIO, CANADA M5B 2C3

Not for

Reproduction

Read this manual carefully and become familiar
with your pressure washer. Know its applications,
its limitations, and any hazards involved.

Important Safety Information

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal
injury hazard. A signal word (DANGER, WARNING, or
CAUTION) is used with the alert symbol to designate a degree
or level of hazard seriousness. A safety symbol may be used
to represent the type of hazard. The signal word NOTICE is
used to address practices not related to personal injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.
NOTICE address practices not related to personal injury.

4

SAFETY RULES

WARNING The engine exhaust from this product

contains chemicals known to the State of California to
cause cancer, birth defects, or other reproductive harm.

WARNING This product contains lead and lead

compounds, known to the State of California to cause
birth defects or other reproductive harm. Wash your

hands after handling this product.

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.
Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,
nausea, fainting or death.
Some chemicals or detergents may be harmful if inhaled
or ingested, causing severe nausea, fainting, or
poisoning.

• Operate pressure washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through
windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area,
even if windows and doors are open.

• Use a respirator or mask whenever there is a chance that
vapors may be inhaled.

• Read all instructions with mask so you are certain the mask will
provide the necessary protection against inhaling harmful
vapors.

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Slippery Surface

Fall

Kickback

Flying Objects

Fluid Injection

Operator’s Manual

Chemical Burn

Not for

Reproduction

WARNING The high pressure stream of water that

this equipment produces can cut through skin
and its underlying tissues, leading to serious

injury and possible amputation.
Spray gun traps high water pressure, even when engine is
stopped and water is disconnected, which can cause
injury.

• DO NOT allow CHILDREN to operate pressure washer.

• NEVER repair high pressure hose. Replace it.

• NEVER repair leaking connections with sealant of any kind.
Replace o-ring or seal.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray gun
while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button
and squeeze spray gun trigger to release high pressure, every
time you stop engine.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or
trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are
correctly attached.

WARNING Contact with muffler area can result in

serious burns.
Exhaust heat/gases can ignite
combustibles, structures or damage

fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of
pressure washer including overhead.

• It is a violation of California Public Resource Code, Section
4442, to use or operate the engine on any forest-covered,
brush-covered, or grass-covered land unless the exhaust
system is equipped with a spark arrester, as defined in Section
4442, maintained in effective working order. Other states or
federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer
to obtain a spark arrester designed for the exhaust system
installed on this engine.

• Replacement parts must be the same and installed in the same
position as the original parts.

5

WARNING Fuel and its vapors are extremely

flammable and explosive.
Fire or explosion can cause severe burns
or death.

WHEN ADDING OR DRAINING FUEL

• Turn pressure washer OFF and let it cool at least 2 minutes
before removing fuel cap. Loosen cap slowly to relieve pressure
in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and
other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are in place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel to
spill.

• DO NOT spray flammable liquids.

WHEN TRANSPORTING, MOVING OR REPAIRING EQUIPMENT

• Transport/move/repair with fuel tank EMPTY or with fuel shutoff
valve OFF.

• DO NOT tip engine or equipment at angle which causes fuel to
spill.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes
dryers, or other appliances that have pilot light or other ignition
source because they can ignite fuel vapors.

WARNING Risk of electrocution.

Contact with power source can cause electric
shock or burn.

• NEVER spray near power source.

WARNING Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will pull hand and
arm toward engine faster than you can let go.
Broken bones, fractures, bruises, or sprains

could result.

• NEVER pull starter cord without first relieving spray gun
pressure.

• When starting engine, pull cord slowly until resistance is felt
and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always
point spray gun in safe direction, press red button and squeeze
spray gun trigger to release high pressure.

• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.

Not for

Reproduction

NOTICE High pressure spray may damage fragile items
including glass.

• DO NOT point spray gun at glass when using red (0°) spray tip.

• NEVER aim spray gun at plants.

NOTICE Improper treatment of pressure washer can
damage it and shorten its life.

• If you have questions about intended use, ask dealer or contact
Sears.

• NEVER operate units with broken or missing parts, or without
protective housing or covers.

• DO NOT by-pass any safety device on this machine.

• DO NOT tamper with governed speed.

• DO NOT operate pressure washer above rated pressure.

• DO NOT modify pressure washer in any way.

• Before starting pressure washer in cold weather, check all parts
of the equipment to be sure ice has not formed there.

• NEVER move machine by pulling on hoses. Use handle provided
on unit.

• Check fuel system for leaks or signs of deterioration, such as
chafed or spongy hose, loose or missing clamps, or damaged
tank or cap. Correct all defects before operating pressure washer.

• This equipment is designed to be used with Sears authorized parts
ONLY. If equipment is used with parts that DO NOT comply with
minimum specifications, user assumes all risks and liabilities.

6

WARNING Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE
WASHER

• Disconnect the spark plug wire from the spark plug and place
the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

WARNING Starter and other rotating parts can

entangle hands, hair, clothing, or accessories.

• NEVER operate pressure washer without protective housing or
covers.

• DO NOT wear loose clothing, jewelry or anything that may be
caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

WARNING Risk of eye injury.

Spray can splash back or propel objects.

• Always wear indirect vented (chemical splash) safety goggles
marked to comply with ANSI Z87.1 when using or in vicinity of
this equipment.

• NEVER substitute safety glasses or dry-condition goggles for
indirect vented safety goggles.

WARNING Use of pressure washer can create

puddles and slippery surfaces.
Kickback from spray gun can cause you
to fall.

• Operate pressure washer from a stable surface.

• The cleaning area should have adequate slopes and drainage to
reduce the possibility of a fall due to slippery surfaces.

• Be extremely careful if you must use the pressure washer from
a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.

WARNING Chemical Burn Hazard.

Chemicals could cause bodily injury, property
damage or death.

• DO NOT use caustic liquid with pressure washer.

• Use ONLY pressure washer safe detergents /soaps. Follow all
manufacturers instructions.

Not for

Reproduction

KNOW YOUR PRESSURE WASHER

Read the Operator’s Manual and safety rules before operating your pressure washer.

Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and
adjustments. Save this manual for future reference.

7

FEATURES AND CONTROLS

F

D

A

B

G

C

S

N

,

M

A - Spray Gun — Controls the application of water onto

cleaning surface with trigger device. Includes trigger lock.

B - Accessory Tray — Provides convenient storage for

accessories, such as gun, spray tips, etc.

C - Spray Tip Extension with Quick Connect — Allows you

to switch between three different spray tips.

D - Recoil Starter — Used for starting the engine manually.
E - Warning/Operating Instructions Tag — Identifies hazards

and proper procedure to start/stop pressure washer.

F - Air Filter — Protects engine by filtering dust and debris

out of intake air.

G - Fuel Tank — Fill tank with regular unleaded fuel. Always

leave room for fuel expansion.

H - Detergent Siphoning Tube/Filter — Use to siphon pressure

washer safe detergents into the low pressure stream.

J - Primer Bulb — Prepares a cold engine for starting.
K - High Pressure Outlet — Connection for high pressure hose.

L - Water Inlet — Connection for garden hose.
M - Automatic Cool Down System — Cycles water through

pump when water reaches 125°-155°F. Warm water will
discharge from pump onto ground. This system prevents
internal pump damage.

N - Pump — Develops high pressure.
P - Throttle Lever — Sets engine in starting mode for recoil

starter and stops a running engine.

R - Oil Fill/Dipstick — Check, add and drain engine oil here.
S - High Pressure Hose — Connect one end of hose to

water pump and the other end to spray gun.

T - Spray Tips — Detergent, 0° and 25°: for various high

pressure cleaning applications.

Items Not Shown:
Identification Label (near rear of base plate) — Provides

model and serial number of pressure washer. Please have
these readily available if calling for assistance.

R

T

P

H

J

E

L

,

K

Not for

Reproduction

Your pressure washer requires some assembly and is ready
for use only after it has been properly serviced with the
recommended oil and fuel.

If you have any problems with the assembly of your
pressure washer, please call the pressure washer helpline
at 1-800-222-3136.

UNPACK THE PRESSURE WASHER

1. Remove everything from carton except pressure washer.

2. Open carton completely by cutting each corner from top
to bottom.

3. Remove pressure washer from carton.

CARTON CONTENTS

Check all contents. If any parts are missing or damaged, call
the pressure washer helpline at 1-800-222-3136.

• Main Unit

• Handle

• Accessory Tray

• High Pressure Hose

• Spray Gun

• Spray Tip Extension with Quick Connect Fitting

• Oil Bottle

• Parts Bag (which includes the following):

• Operator’s Manual

• Bag containing 3 multi–colored Spray Tips

• Handle Fastening Hardware Kit (which includes):

• Carriage Bolts (2)

• Plastic Knobs (2)

• Tree Clips (4)

Become familiar with each piece before assembling the
pressure washer. Identify all contents with the illustration on
page 7. If any parts are missing or damaged, call the
pressure washer helpline at 1-800-222-3136.

ASSEMBLING PRESSURE WASHER

Your Craftsman pressure washer will need assembly before
operation:

1. Attach handle and accessory tray.

2. Add oil to engine crankcase.

3. Add fuel to fuel tank.

4. Connect pressure hose to spray gun and pump.

5. Connect water supply to pump.

6. Attach spray tip extension to spray gun.

7. Select/attach quick connect spray tip to spray tip
extension.

Attach Handle and Accessory Tray

1. Place handle (A) onto handle supports (B) connected to

main unit. Make sure holes in handle align with holes on
handle supports.

NOTICE It may be necessary to move the handle supports
from side to side in order to align the handle so it will slide
over the handle supports.

2. Insert carriage bolts (C) through holes from inside of
unit and attach a plastic knob (D) from outside of unit.
Tighten by hand.

3. Place accessory tray (E) over holes (F) on handle
(viewing from front of unit). Push the tree clips (G) into
the holes until they sit flat against the accessory tray.

4. Insert multi–colored quick connect spray tips and other
supplied accessories in spaces provided in accessory
tray. See How to Use Accessory Tray.

8

ASSEMBLY

A

B

D

C

E

G

F

Not for

Reproduction

Add Engine Oil

1. Place pressure washer on a flat, level surface.

2. Clean area around oil fill and remove yellow oil fill
cap/dipstick.

3. Using oil funnel (optional), slowly pour contents of
provided oil bottle into oil fill opening.

NOTICE Improper treatment of pressure washer can
damage it and shorten its life.

• DO NOT attempt to crank or start the engine before it has been

properly serviced with the recommended oil. This may result in an
engine failure.

4. Replace oil fill cap/dipstick and fully tighten.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude

use, see High Altitude.

• Gasoline with up to 10% ethanol (gasohol) or up to 15%

MTBE (methyl tertiary butyl ether) is acceptable.

NOTICE Avoid pressure washer damage.
Failure to follow Operator’s Manual for fuel
recommendations voids warranty.

• DO NOT use unapproved gasoline such as E85.

• DO NOT mix oil in gasoline.

• DO NOT modify engine to run on alternate fuels.

To protect the fuel system from gum formation, mix in a fuel
stabilizer when adding fuel. See Storage. All fuel is not the
same. If you experience starting or performance problems
after using fuel, switch to a different fuel provider or change
brands. This engine is certified to operate on gasoline. The
emission control system for this engine is EM (Engine
Modifications).

1. Clean area around fuel fill cap, remove cap.

2. Slowly add regular unleaded fuel (A) to fuel tank (B). Be
careful not to overfill. Allow about 1.5" (4 cm) (C) of tank
space for fuel expansion.

3. Install fuel cap and wait for any spilled fuel to evaporate.

CAUTION! Alcohol-blended fuels (called gasohol, ethanol or

methanol) can attract moisture, which leads to separation and
formation of acids during storage. Acidic gas can damage the
fuel system of an engine while in storage.

To avoid engine problems, the fuel system should be treated
with a fuel preserver or emptied before storage of 30 days or
longer. If adding a fuel preserver, fill the fuel tank with fresh
fuel. If only partially filled, air in the tank will promote fuel
deterioration during storage. If fuel preserver is not used,
drain the fuel tank, start the engine and let it run until the fuel
lines and carburetor are empty. Use fresh fuel next season.
See Storage for additional information.

NEVER use engine or carburetor cleaner products in the fuel
tank as permanent damage may occur.

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum
85 octane / 85 AKI (89 RON) gasoline is acceptable. To
remain emissions compliant, high altitude adjustment is
required. Operation without this adjustment will cause
decreased performance, increased fuel consumption, and
increased emissions. See a qualified Sears dealer for high
altitude adjustment information. Operation of the engine at
altitudes below 2,500 feet (762 meters) with the high altitude
kit is not recommended.

WARNING Fuel and its vapors are extremely

flammable and explosive.
Fire or explosion can cause severe burns
or death.

WHEN ADDING FUEL

• Turn pressure washer OFF and let it cool at least 2 minutes
before removing fuel cap. Loosen cap slowly to relieve pressure
in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and
other ignition sources.

• DO NOT light a cigarette or smoke.

9

C

B

A

Not for

Reproduction

Connect Hose and Water Supply to Pump

NOTICE DO NOT run the pump without the water supply
connected and turned on.

• Damage to equipment resulting from failure to follow this
instruction will void warranty.

NOTICE Remove and discard the shipping caps from the
pump’s high pressure outlet and water inlet before attaching
hoses.

1. Uncoil high pressure hose and attach one end of hose to

base of spray gun. Tighten by hand.

2. Attach other end of high pressure hose to high pressure

outlet on pump. Tighten by hand.

3. Before connecting garden hose to water inlet, inspect

inlet screen (A). Clean screen if it contains debris or have
it replaced if damaged. DO NOT run pressure washer if

inlet screen is damaged or missing.

4. Run water through garden hose for 30 seconds to flush
it of debris. Turn off water.

NOTICE DO NOT siphon standing water for the water
supply. Use ONLY cold water (less than 100°F).

5. Connect garden hose (not to exceed 50 feet in length) to
water inlet. Tighten by hand.

NOTICE Using a One Way Valve (vacuum breaker or check
valve) at pump inlet can cause pump or inlet connector
damage.

• There MUST be at least ten feet of unrestricted garden hose

between the pressure washer inlet and any device, such as a
vacuum breaker or check valve.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

6. Turn ON the water, press red button (B) on the gun and

squeeze the trigger to purge the pump system of air and
impurities.

Checklist Before Starting Engine

Review the unit to ensure you have performed all of the
following:

1. Be sure to read Safety Rules and Operation sections
before using the pressure washer.

2. Make sure handle is in place and secure.

3. Check that oil has been added to proper level in engine
crankcase.

4. Add proper fuel to fuel tank.

5. Check for proper hose connections (high pressure and
water supply) and that there are no kinks, cuts, or
damage to the high pressure hose.

6. Provide proper water supply (not to exceed 100°F).

9

B

A

WARNING The high pressure stream of water that

this equipment produces can cut through skin
and its underlying tissues, leading to serious
injury and possible amputation.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray gun
while system is pressurized.

• Always be certain spray gun, nozzles and accessories are
correctly attached.

WARNING Risk of eye injury.

Spray can splash back or propel objects.

• Always wear indirect vented (chemical splash) safety goggles
marked to comply with ANSI Z87.1 when using or in vicinity of
this equipment.

• NEVER substitute safety glasses or dry-condition goggles for
indirect vented safety goggles.

Not for

Reproduction

HOW TO USE YOUR PRESSURE WASHER

If you have any problems operating your pressure washer,
please call the pressure washer helpline at 1-800-222-3136.

Pressure Washer Location

Pressure Washer Clearance

Place pressure washer outdoors in an area that will not
accumulate deadly exhaust gas. DO NOT place pressure
washer where exhaust gas (A) could accumulate and enter
inside or be drawn into a potentially occupied building.
Ensure exhaust gas is kept away from any windows, doors,
ventilation intakes, or other openings that can allow exhaust
gas to collect in a confined area. Prevailing winds and air
currents should be taken into consideration when positioning
pressure washer.

To Start Your Pressure Washer

To start your engine-powered pressure washer for the first
time, follow these instructions step-by-step. This information
also applies whenever you start the engine after you have let
the pressure washer sit idle for at least a day.

1. Place pressure washer outside near an water source
capable of supplying water at a flow rate greater than

3.2 gallons per minute and no less than 20 PSI at
pressure washer end of garden hose.

2. Check that high pressure hose is tightly connected to
spray gun and pump. See Assembly for illustrations.

3. Make sure unit is in a level position.

4. Connect garden hose to water inlet on pressure washer
pump.

NOTICE DO NOT run the pump without the water supply
connected and turned on.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

5. Turn ON the water, press red button on the gun and
squeeze the trigger to purge the pump system of air and
impurities.

6. Attach spray tip extension to spray gun. Tighten by
hand.

7. Choose spray tip you want to use and insert it into spray
tip extension. See How to Use Spray Tips.

8. Move throttle lever (B) to “Fast” position, shown as a
rabbit.

OPERATION

A

B

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poisonous gas.
Breathing carbon monoxide can cause headache,
fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

• Operate pressure washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through
windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area,
even if windows and doors are open.

WARNING Exhaust heat/gases can ignite

combustibles, structures or damage fuel tank
causing a fire.

• Keep at least 5 ft. (152 cm) clearance on all sides of pressure
washer including overhead.

11

Not for

Reproduction

To start the engine for the very first time:

9A. Push primer bulb firmly 5 times, waiting 2 seconds

between each push.

To start engine thereafter:

9B. Press primer bulb firmly 3 times, waiting 2 seconds

between each push. For a warm engine, DO NOT press
primer bulb.

NOTICE Before starting the pressure washer, be sure you
are wearing safety goggles as described below.

10. When starting engine, position yourself as
recommended and grasp starter grip handle and pull
slowly until you feel some resistance. Then pull rapidly
to start engine.

11. Return recoil starter slowly. DO NOT let rope “snap
back” against starter.

NOTICE Always keep the throttle lever in the “Fast” position
when operating the pressure washer.

12

WARNING Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will pull hand and
arm toward engine faster than you can let go.
Broken bones, fractures, bruises, or sprains

could result.

• NEVER pull starter cord without first relieving spray gun
pressure.

• When starting engine, pull cord slowly until resistance is felt
and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always
point spray gun in safe direction, press red button and squeeze
spray gun trigger to release high pressure.

• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.

WARNING Contact with muffler area can result in

serious burns.
Exhaust heat/gases can ignite
combustibles, structures or damage

fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of
pressure washer including overhead.

• It is a violation of California Public Resource Code, Section
4442, to use or operate the engine on any forest-covered,
brush-covered, or grass-covered land unless the exhaust
system is equipped with a spark arrester, as defined in Section
4442, maintained in effective working order. Other states or
federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer
to obtain a spark arrester designed for the exhaust system
installed on this engine.

• Replacement parts must be the same and installed in the same
position as the original parts.

WARNING The high pressure stream of water that

this equipment produces can cut through skin
and its underlying tissues, leading to serious

injury and possible amputation.
Spray gun traps high water pressure, even when engine is
stopped and water is disconnected, which can cause
injury.

• DO NOT allow CHILDREN to operate pressure washer.

• Keep high pressure hose connected to pump and spray gun
while system is pressurized.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or
trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are
correctly attached.

WARNING Risk of eye injury.

Spray can splash back or propel objects.

• Always wear indirect vented (chemical splash) safety goggles
marked to comply with ANSI Z87.1 when using or in vicinity of
this equipment.

• NEVER substitute safety glasses or dry-condition goggles for
indirect vented safety goggles.

Not for

Reproduction

How to Stop Your Pressure Washer

1. Release spray gun trigger and let engine idle for two
minutes.

2. Move throttle to SLOW position, then STOP position.

3. ALWAYS point spray gun in a safe direction, push red
button and squeeze spray gun trigger to release retained
high water pressure.

NOTICE Spray gun traps high water pressure, even when
engine is stopped and water is disconnected.

How to Use Accessory Tray

The unit is equipped with an accessory tray with places to
store your spray gun, spray tip extension and quick connect
spray tips. There is also a hook at the front of the accessory
tray to hold your high pressure hose.

NOTICE The extra hole in the tray is for storing a utility brush.
The extra clip in the tray is for storing a turbo spray tip. The
brush and turbo nozzle are NOT included with your pressure
washer. You can buy these items as optional accessories.

1. Place spray tip extension through hole on accessory
tray, as shown.

2. Place spray gun through hole on accessory tray on right
side of unit.

3. Hang high pressure hose on hook attached to accessory
tray on front of tray as shown.

4. Insert multi–colored spray tips in spaces provided in
accessory tray.

How to Use Spray Tips

The quick–connect on the spray tip extension allows you to
switch between three different quick connect spray tips. The
spray tips vary the spray pattern as shown below.

Follow these instructions to change spray tips:

1. Pull back collar on quick–connect and pull current spray
tip off. Store spray tips in holder provided on the
accessory tray.

2. Select desired spray tip:

• For maximum rinsing (higher pressure and lower

flow), for stubborn or hard to reach surface such as
second story surfaces, paint removal, oil stains, rust
removal or other stubborn substances (tar, gum,
grease, wax, etc.), select red 0° spray tip.

• For delicate rinse (lower pressure and higher flow),

for gentle cleaning of cars/trucks, boats, RV’s, patio
furniture, lawn equipment, etc., select green 25°
spray tip.

• To apply detergent, applies project specific cleaners

to help break down stubborn dirt and grime on a
variety of surfaces, select black detergent spray tip.

Usage Tips

• For most effective cleaning, keep spray tip from 8 to

24 inches (20 to 61 cm) away from cleaning surface.

• If you get spray tip too close, especially using a high

pressure spray tip, you may damage surface being cleaned.

• DO NOT get closer than 6 inches (15 cm) when cleaning

tires.

WARNING The high pressure stream of water that

this equipment produces can cut through skin
and its underlying tissues, leading to serious
injury and possible amputation.

• NEVER exchange spray tips without the trigger locked on the
spray gun.

• DO NOT twist spray tips while spraying.

13

WARNING The high pressure stream of water that

this equipment produces can cut through skin
and its underlying tissues, leading to serious

injury and possible amputation.
Spray gun traps high water pressure, even when engine is
stopped and water is disconnected, which can cause
injury.

• Keep high pressure hose connected to pump and spray gun
while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button
and squeeze spray gun trigger to release high pressure, every
time you stop engine.

Black

Use to apply

detergent

25° Green

1650 PSI

2.2 GPM

0° Red

2200 PSI

1.9 GPM

Low Pressure

High Pressure

Not for

Reproduction

Cleaning and Applying Detergent

To apply detergent, follow these steps:

1. Review use of spray tips.

2. Prepare detergent solution as required by job.

3. Place small filter end of detergent siphoning tube into
detergent container.

NOTICE Contact with the hot muffler can damage detergent
siphoning tube.

• When inserting the siphon into a detergent solution bottle, route

the tube so as to keep it from inadvertently contacting the hot
muffler.

NOTICE Make sure the filter is fully submerged in detergent
while applying detergent.

4. Make sure black spray tip is installed.

NOTICE Detergent cannot be applied with the high pressure
spray tips (Green or Red).

5. Make sure garden hose is connected to water inlet.
Check that high pressure hose is connected to spray gun
and pump. Turn on water.

NOTICE You must attach all hoses before you start the
engine.

• Starting the engine without all the hoses connected and without

the water turned ON will damage the pump.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

6. Start engine following instructions How to Start Your
Pressure Washer.

7. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.

8. Allow detergent to "soak in" for 3-5 minutes before
washing and rinsing. Reapply as needed to prevent
surface from drying. DO NOT allow detergent to dry on
(prevents streaking).

NOTICE You must flush the detergent siphoning system
after each use by placing the filter into a bucket of clean
water, then run the pressure washer in low pressure for 1-2
minutes.

Pressure Washer Rinsing

For Rinsing:

1. Remove black spray tip from nozzle extension.

2. Select and install desired high pressure spray tip
following instructions How to Use Spray Tips.

3. Keep the spray gun a safe distance from the area you
plan to spray.

4. Apply a high pressure spray to a small area and then
check surface for damage. If no damage is found, you
can assume it is okay to continue rinsing.

5. Start at top of area to be rinsed, working down with
same overlapping strokes as you used for cleaning.

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must flush it
with clean water before stopping the engine.

1. Place detergent siphoning tube/filter in a bucket full of
clean water.

2. Remove high pressure spray tip from spray tip
extension.

3. Select and install black detergent spray tip following
instructions How to Use Spray Tips.

4. Flush for 1-2 minutes.

5. Shut off engine following instructions How to Stop
Pressure Washer and turn off water supply.

6. ALWAYS point spray gun in a safe direction push red
button and squeeze spray gun trigger to release retained
high water pressure.

NOTICE Spray gun traps high water pressure, even when
engine is stopped and water is disconnected.

Automatic Cool Down System (Thermal Relief)

If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray gun,
circulating water in the pump can reach temperatures above
125°F. The system engages to cool the pump by discharging
the warm water onto the ground.

14

WARNING Kickback from spray gun can cause you to

fall.

• Operate pressure washer from a stable surface.

• Be extremely careful if you must use the pressure washer from
a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.

WARNING The high pressure stream of water that

this equipment produces can cut through skin
and its underlying tissues, leading to serious

injury and possible amputation.
Spray gun traps high water pressure, even when engine is
stopped and water is disconnected, which can cause
injury.

• Keep high pressure hose connected to pump and spray gun
while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button
and squeeze spray gun trigger to release high pressure, every
time you stop engine.

WARNING Chemical Burn Hazard.

Chemicals could cause bodily injury, property
damage or death.

• DO NOT use caustic liquid with pressure washer.

• Use ONLY pressure washer safe detergents /soaps. Follow all
manufacturers instructions.

Not for

Reproduction

ENGINE TECHNICAL INFORMATION

This is a single cylinder, L-head, air cooled engine. It is a low
emissions engine.

In the State of California, Model 100000 engines are certified
by the California Air Resources Board to meet emissions
standards for 125 hours. Such certification does not grant
the purchaser, owner or operator of this engine any
additional warranties with respect to the performance or
operational life of this engine. The engine is warranted solely
according to the product and emissions warranties stated
elsewhere in this manual.

Power Ratings

The gross power rating for individual gas engine models is
labeled in accordance with SAE (Society of Automotive
Engineers) code J1940 (Small Engine Power & Torque
Rating Procedure), and rating performance has been
obtained and corrected in accordance with SAE J1995
(Revision 2002-05). Torque values are derived at 3060 RPM;
horsepower values are derived at 3600 RPM. Actual gross
engine power will be lower and is affected by, among other
things, ambient operating conditions and engine-to-engine
variability. Given both the wide array of products on which
engines are placed and the variety of environmental issues
applicable to operating the equipment, the gas engine will not
develop the rated gross power when used in a given piece of
power equipment (actual "on-site" or net power). This
difference is due to a variety of factors including, but not
limited to, accessories (air cleaner, exhaust, charging,
cooling, carburetor, fuel pump, etc.), application limitations,
ambient operating conditions (temperature, humidity,
altitude), and engine-to-engine variability. Due to
manufacturing and capacity limitations, Briggs & Stratton
may substitute an engine of higher rated power for this
Series engine.

This pressure washer is rated in accordance to the Pressure
Washer Manufacturers Association (PWMA) standard PW101
(Testing and Rating Performance of Pressure Washers).

PRODUCT SPECIFICATIONS

Pressure Washer Specifications

Max Outlet Pressure . . . . . . . . . . . . . . . . . . . . . . . 2,200 PSI

Max Flow Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 GPM

Detergent Mix . . . . . . . . . . . . . . . . . . . . . . . . Use as directed

Water Supply Temperature . . . . . . . . . . Not to exceed 100°F

Engine Specifications

Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.56 in. (65.1 mm)

Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.87 in. (47.6 mm)

Displacement . . . . . . . . . . . . . . . . . . . . . . . . 9.67 in. (158.6 cc)

Spark Plug

Type: . . . . . . . . . . . . .

Briggs & Stratton 802592 or 5095D

Set Gap To: . . . . . . . . . . . . . . . . . . . . . . 0.030inch (0.76mm)

Armature Air Gap: . . . . . . . . . . . 0.006-0.010 in.(0.15-0.25mm)

Valve clearance with valve springs installed and piston 1/4 in.
(6 mm) past top dead center (check when engine is cold).

Intake . . . . . . . . . . . . . . . . . . . . 0.005-0.007 in.(0.13-0.18 mm)

Exhaust . . . . . . . . . . . . . . . . . . 0.007-0.009 in.(0.18-0.23 mm)

Fuel Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0 Quarts

Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . 18 Ounces (0.5 liter)

NOTICE For practical operation, the engine load should not
exceed 85% of rated power. Engine power will decrease
3-1/2% for each 1,000 feet (300 meters) above sea level and
1% for each 10° F (5.6° C) above 77° F (25° C). It should
operate satisfactorily at an angle up to 15°.

15

SPECIFICATIONS

Not for

Reproduction

OWNER’S RESPONSIBILITIES

Follow the hourly or calendar intervals, whichever occurs
first. More frequent service is required when operating in
adverse conditions noted below.

1

Clean if clogged. Replace if perforated or torn.

2

Service more often under dirty or dusty conditions.

General Recommendations

Regular maintenance will improve the performance and
extend the life of the pressure washer. See any Sears or
other qualified service dealer for service.

The pressure washer warranty does not cover items that
have been subjected to operator abuse or negligence. To
receive full value from the warranty, the operator must
maintain pressure washer as instructed in this manual
including proper storage as detailed in Storage.

Some adjustments will need to be made periodically to
properly maintain your pressure washer.

All service and adjustments should be made at least once
each season. Follow the requirements in the Maintenance
Schedule chart above.

NOTICE Once a year you should clean or replace the spark
plug and replace the air filter. A new spark plug and clean air
filter assure proper fuel-air mixture and help your engine run
better and last longer.

Pump Oil

DO NOT attempt any oil maintenance on this pump. The
pump is pre-lubricated and sealed from the factory, requiring
no additional maintenance for the life of the pump.

Emissions Control

Maintenance, replacement, or repair of the emissions
control devices and systems may be performed by any non­road engine repair establishment or individual. However,

to obtain ”no charge” emissions control service, the work
must be performed by a factory authorized dealer. See the
Emissions Warranty.

Before Each Use

1. Check engine oil level.

2. Clean debris.

3. Check water inlet screen for damage.

4. Check high pressure hose for leaks.

5. Check gun and spray tip extension assembly for leaks.

6. Purge pump of air and contaminants.

PRESSURE WASHER MAINTENANCE

Clean Debris

Daily or before use, clean accumulated debris from pressure
washer. Keep linkage, spring and controls clean. Keep area
around and behind muffler free from any combustible debris.
Inspect cooling air slots and openings on the pressure
washer. These openings must be kept clean and
unobstructed.

Pressure washer parts should be kept clean to reduce the
risk of overheating and ignition of accumulated debris.

• Use a damp cloth to wipe exterior surfaces clean.

NOTICE Improper treatment of pressure washer can
damage it and shorten its life.

• DO NOT insert any objects through cooling slots.

• Use a soft bristle brush to loosen caked on dirt, oil, etc.

• Use a vacuum cleaner to pick up loose dirt and debris.

Check and Clean Inlet Screen

Examine garden hose inlet screen. Clean if it is clogged or
replace if it is torn.

Check High Pressure Hose

High pressure hoses can develop leaks from wear, kinking,
or abuse. Inspect hose before each use. Check for cuts,
leaks, abrasions, bulging of cover, or damage or movement
of couplings. If any of these conditions exist, replace hose
immediately.

MAINTENANCE

First 5 Hours

• Change engine oil

Every 8 Hours or Daily

• Check/ clean water inlet screen

1

• Check high pressure hose

• Check detergent siphoning hose

• Check spray gun and assembly for leaks

• Clean debris

• Check engine oil level

Every 25 Hours or Yearly

• Service engine air cleaner

2

Every 50 Hours or Yearly

• Change engine oil

2

• Inspect muffler and spark arrester

Every 100 Hours or Yearly

• Service spark plug

• Clean cooling system

2

16

WARNING The high pressure stream of water that

this equipment produces can cut through skin
and its underlying tissues, leading to serious
injury and possible amputation.

• NEVER repair high pressure hose. Replace it.

• Replacement hose rating MUST exceed maximum pressure
rating of unit.

Not for

Reproduction

Check Gun and Spray Tip Extension

Examine hose connection to spray gun and make sure it is
secure. Test trigger by pressing it and making sure it springs
back into place when you release it. Do not depress red button
and test trigger. You should not be able to press trigger. Replace
spray gun immediately if it fails any of these tests.

Spray Tip Maintenance

A pulsing sensation felt while squeezing the spray gun trigger
may be caused by excessive pump pressure. The principal
cause of excessive pump pressure is a spray tip clogged or
restricted with foreign materials, such as dirt, etc. To correct
the problem, immediately clean the spray tip following these
instructions:

1. Shut off engine and turn off water supply.

2. ALWAYS point spray gun in a safe direction, press red
button and and squeeze spray gun trigger to release
retained high water pressure.

3. Remove spray tip from end of spray tip extension.

4. Use a small paper clip to free any foreign material
clogging or restricting spray tip (A).

5. Remove spray tip extension from spray gun.

6. Using a garden hose, remove additional debris by back
flushing water through spray tip extension. Back flush
between 30 to 60 seconds.

7. Reinstall spray tip into spray tip extension.

8. Reconnect spray tip extension to spray gun.

9. Make sure garden hose is connected to water inlet.
Check that high pressure hose is connected to spray gun
and pump. Turn on water.

10. Start engine following instructions How to Start Your
Pressure Washer.

11. Test pressure washer by operating with each quick
connect spray tip.

O–Ring Maintenance

Purchase an O–Ring Repair Kit at your local Sears or by calling
1-800-4-MY-HOME (469-4663) or online at www.sears.com. It
is not included with the pressure washer. This kit includes
replacement o-rings, rubber washer and water inlet filter. Refer to
the instruction sheet provided in the kit to service your unit’s
o-rings.

ENGINE MAINTENANCE

Oil

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF, SG,
SH, SJ or higher. DO NOT use special additives.

Outdoor temperatures determine the proper oil viscosity for
the engine. Use the chart to select the best viscosity for the
outdoor temperature range expected.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.
** Above 80°F (27°C) the use of 10W30 may cause increased oil

consumption. Check oil level more frequently.

NOTICE Synthetic oil meeting ILSAC GF-2, API
certification mark and API service symbol with
“SJ/CF ENERGY CONSERVING” or higher, is an
acceptable oil at all temperatures. Use of synthetic oil
does not alter required oil change intervals.

17

A

WARNING The high pressure stream of water that

this equipment produces can cut through skin
and its underlying tissues, leading to serious

injury and possible amputation.
Spray gun traps high water pressure, even when engine is
stopped and water is disconnected, which can cause
injury.

• Keep high pressure hose connected to pump and spray gun
while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button
and squeeze spray gun trigger to release high pressure, every
time you stop engine.

WARNING The high pressure stream of water that

this equipment produces can cut through skin
and its underlying tissues, leading to serious
injury and possible amputation.

• NEVER repair leaking connections with sealant of any kind.
Replace o-ring or seal.

WARNING Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE
WASHER

• Disconnect the spark plug wire from the spark plug and place
the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Not for

Reproduction