Craftsman 973.11147 User Manual
Owner's Manual
Variable Speed / Reversible
318in. 13.2 VOLTS CORDLESS DRILL-DRIVER
Model No.
973.111470
Save this manual for
future reference
CAUTION: Read and follow all
SafetyRules and Operating In-
structions before first use of this
product.
Customer Help Line: 1-800-932-3188
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visitthe Craftsman web page: www.sears.com/craftsman
972000-789
8-0O
• Safety
• Features
• Operation
• Maintenance
• Parts List
®
• Warranty ......................................................................................................................................................... 2
• Introduction and Product Specifications ......................................................................................................... 2
• Rules For Safe Operation ........................................................................................................................... 3-5
A. Important Safety Rules For Battery Tools .............................................................................................. 4
B. Important Safety Instructions For Charger ............................................................................................. 4
C. Important Information For Recharging Hot Batteries ............................................................................. 5
• Accessodes .................................................................................................................................................... 6
• Features ........................................ ................................................................................................................. 6
• Operation ................................................................................................................................................... 7-12
• Maintenance ................................................................................................................................................. 12
• Battery Pack Removal and Preparation For Recycling ................................................................................ 13
• Exploded View and Repair Parts List........................................................................................................... 15
• Parts Ordering / Service ............................................................................................................................... 16
FULL ONE YEAR WARRANTY ON CRAFTSMAN3/8 in. CORDLESS DRILL-DRIVER
If this CRAFTSNAN 3/8 in. Cordless Drill-Driver fails to give complete satisfaction within one year from the date of
purchase, RETURN IT TO THE NEAREST SEARS STORE OR SEARS SERVICE CENTER IN THE UNITED
STATES, and Sears will repair it, free of charge.
If this CRAFTSNIIN 3/8 in. Cordless DdlI-Ddver is used for commercial or rental purposes, this warranty applies
for only 90 days from the date of purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817 WA, Hoffmen Estates, IL 60179
Your drill-driver has many features for making drilling
operations more pleasant and enjoyable. Safety,
performance and dependability have been given top
pdority in the design of this ddll-ddver making it easy
to maintain and operate.
CAUTION: Carefully read through this entire
owner's manual before using your new ddll-ddver.
Pay close attention to the Rules For Safe
Operation, Warnings and Cautions. If you use
your drill-driver properly and only for what it is
intended, you will enjoy years of safe, reliable
service.
SPECIFICATIONS:
Chuck Capacity
Motor
Charger Rating
No Load Speed
Switch
Charge Rate
Maximum Torque
2
3/8 in.
13.2 Volts DC
120Volts, 60 Hz, AC Only
0 - 600 RPM
Vadable Speed - Reversible
3 - 5 Hours
100 in./Ibs.
Thepurposeofsafetysymbolsisto attractyourattentionto possibledangers.Thesafetysymbols,and
theexplanationswiththem,deserveyourcarefulattentionandunderstanding.Thesafetywarningsdo
notbythemselveseliminateanydanger.TheInstructionsorwarningstheygivearenotsubstitutesfor
properaccidentpreventionmeasures.
SYMBOL MEANING
SAFETY ALERT SYMBOL:
Indicates warning or caution. May be used in conjunction with other symbols or pictographs.
A
&
WARNING: Failure to obey a safety warning can result in serious injuryto yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
CAUTION: Failure to obey a safety warning may result in property damage or personal injury to
yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock
and personal injury.
NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.
WARNING: Do not attempt to operate this tool •
until you have read thoroughly and understand
completely all instructions, safety rules, etc.
contained in this manual. Failure to comply can
result in accidents involving fire, electric shock,
or serious personal injury. Save owner's manual
and review frequently for continuing safe
operation, and instructing others who may use
this tool.
READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL. Read owner's
manual carefully. Learn its applications and
limitations as well as the specific potential hazards
related to this tool.
• GUARD AGAINST ELECTRICAL SHOCK by
preventing body contact with grounded surfaces.
For example: Pipes, radiators, ranges, refrigerator
enclosures.
• KEEP WORK AREA CLEAN. Cluttered areas ahd
benches invite accidents.
• AVOID DANGEROUS ENVIRONMENT. Don't use
power tool in damp or wet locations orexpose to
rain. Keep work area well lit.
• KEEP CHILDREN AND VISITORS AWAY. All
visitors should wear safety glasses and be kept a
safe distance from work area. Do not let visitors
contact tool or extension cord.
• STORE IDLE TOOLS. When not in use tools
should be stored in a dry and high or locked-up
place - out of the reach of children.
• DON'T FORCE TOOL. It will do the job better and
safer at the rate for which it was designed.
USE RIGHT TOOL. Don't force small tool or
attachment to do the job of a heavy duty tool. Don't
use tool for purpose not intended - for example - A
circular saw should never be used for cutting tree
limbs or logs.
WEAR PROPER APPAREL. Do not wear loose
clothing or jewelry that can get caught in tool's
moving parts and cause personal injury. Rubber
gloves and nonskid footwear are recommended
when working outdoors. Wear protective hair
covering to contain long hair and keep it from being
drawn into nearby air vents.
• ALWAYS WEAR SAFETY GLASSES. Everyday
eyeglasses have only impact-resistant lenses; they
are NOT safety glasses.
• PROTECT YOUR LUNGS. Wear a face mask or
dust mask if operation is dusty.
• PROTECT YOUR HEARING.'Wear hearing
protection during extended periods of operation.
• SECURE WORK. Use clamps or a vise to hold
work. It's safer than using your hand and itfrees
both hands to operate tool.
• DON'T OVERREACH. Keep proper footing and
balance at all times. Do not use on a ladder or
unstable support.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp
at all times, and clean for best and safest perfor-
mance. Follow instructions for lubricating and
changing accessories.
• REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
3
RULES FOR SAFE OPERATION (Continued)
• NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite flam-
mable liquids, gases, or fumes.
• KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based products or any strong
solvents to clean your tool.
• STAY ALERT. Watch what you are doing and use
common sense. Do not operate tool when you are
tired. Do not rush.
• CHECK DAMAGED PARTS. Before further use of
the tool, a guard or other part that isdamaged
should be carefully checked to determine that itwill
operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation.
A guard or other part that is damaged should be
propedy repaired or replaced by an authorized
service center unless indicated elsewhere in this
instruction manual. =.
• DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
• DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of drugs,
alcohol, or any medication.
• DRILLING OR DRIVING SCREWS INTO
ELECTRICAL WIRING IN WALLS, CEILINGS,
OR OTHER AREAS CAN CAUSE THE BIT OR
CHUCK TO BECOME ELECTRICALLY LIVE. Do
not touch metal parts when drilling into a wall;
grasp only the insulated handle(s) or plastic
housing when using this tool. Make sure hidden
electrical wiring, water pipes, and mechanical
hazards are not in the path of the bit when drilling
into a wall.
DO NOT PLACE BATTERY TOOLS OR THEIR
BATTERIES NEAR FIRE OR HEAT. They may
explode.
• DO NOT CHARGE BATTERY TOOL IN A DAMP
OR WET LOCATION.
• Your battery tool should be charged in a location
where the temperature is more than 50°F but less
than 100°F.
• Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets in your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention.
• If carrying your battery tool at your side, make sure
it is not running and your finger is not on the
switch. Avoid accidental starting.
• SECURE WORK before applying power. NEVER
hold workpiece in your hand or across your legs.
• WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER
• SAVE THESE INSTRUCTIONS. This manual
contains important safety and operating
instructions for battery charger item number
9-11065 (982033-001).
• Before using battery charger, read all instructions
and cautionary markings in thismanual, on battery
charger, and product using battery charger.
AWARNING: To reduce risk of injury, charge only
nickel-cadmium type rechargeable batteries. Other
types of batteries may burst causing personal
injury and damage.
• INSPECT FOR and remove all nails from lumber
before drilling.
IMPORTANT SAFETY RULES FOR BATTERY
TOOLS
• Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories.
• USE ONLY THE CHARGER PROVIDED WITH
YOUR BATTERY TOOL. Do not substitute any
other charger. Use of another charger could cause
batteries to explode causing possible serious
injury.
• Do not expose charger to rain or snow.
• Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a
risk of fire, electric shock, or injuryto persons.
• To reduce risk of damage to charger body and
cord, pull by charger body rather than cord when
disconnecting charger.
• Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
RULES FOR SAFE OPERATION (Continued)
MnAn extension cord should not be used unless
:+'.
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock.
If extension cord must be used, make sure:
a. That pins on plug of extension cord are the
same number, size and shape as those of plug
on charger.
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough forAC ampere
rating of charger as specified below:
Cord Length (Feet) 25' 50' 100'
Cord Size (AWG) 16 16 16
Note: AWG = American Wire Gage
DO NOT OPERATE CHARGER WITH A
DAMAGED CORD OR PLUG. If damaged,
have replaced immediately by a qualified
serviceman.
B Do not operate charger ifit has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman.
• Do not disassemble charger; take it to a qualified
serviceman when service or repair is required.
Incorrect reassembly may result in a riskof electric
shock or fire.
M
To reduce dsk of electric shock, unplug charger
from outlet before attempting any maintenance or
cleaning. Turning off controls will not reduce this
risk.
B Do not use charger outdoors.
B Disconnect charger from power supply when not in
use.
M SAVE THESE INSTRUCTIONS. Refer to them
frequently and use them to instruct others who may
use this tool. If you loan someone this tool, loan
them these instructions also.
,_WARNING: Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known
to cause cancer, birth defects or other reproduc-
tive harm. Some examples of these chemicals
are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies,
depending on how often you do this type of work.
To reduce your exposure to these chemicals:
work in a well ventilated area, and work with
approved safety equipment, such as those dust
masks that are specially designed to filter out
microscopic particles.
,_ Look for this symbol to pointout important safety precautions. Itmeans attentionT!!Your safety is
involved.
SAVE THESE INSTRUCTIONS
IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES
When using your driU-ddvercontinuously, the batteries in your battery pack will become hot. You should let a hot
battery pack cool down for approximately 30 minutes before attempting to recharge.
Note: This situation only occurs when continuous use of your drill causes the batteries to become hot. It does
not occur under normal circumstances. Refer to "CHARGING BATTERY PACK" for normal recharging of
batteries. If the charger does not charge your battery pack under normal circumstances, return both the battery
pack and charger to your nearest Sears repair center for electrical check.
& WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes,
which can result in severe eye damage. Before beginning power tool operation, always
wear safety goggles or safety glasses with side shields and a full face shield when needed.
We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety
glasses with side shields, available at Sears Retail Stores.
5
Loading...