Page 1
Owner's ,Manual
ICRAFTSMAN I
3/8 in., 14.4,VOLTS CORDLESS DRILL-DRIVER
Variable Speed / Reversible
Model No.
973.111350
Save this manual for
future reference
_1_CAUTION: Read and follow all
Safety Rules and Operating
Instructions before first use of this
product.
Customer Help Line: 1-800-932-3188
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
visit the Craftsman web page: www.sears.com/craftsman
9720OO-923
8-01
• Safety
• Features
• Operation
• Maintenance
• Parts List
Page 2
TABLE OF CONTENTS
• General Safety Rules ................................................................................................................................................. 2-3
• Specific SafetyRules/Symbols .................................................................................................................................. 3-5
• Features ......................................................................................................................................................................... 6
• Operation ............................................................................................................................... 7-11
• Maintenance ................................................................................................................................................................. 12
• Battery Removal ........................................................................................................................................................... 12
• Accessories ............. _. ...................................................... _.................................................................................. 13
m Warranty ....................................................................................................................................................................... 13
• Exploded View And Repair Parts List .......................................................................................................................... 15
• Parts Ordering / Service ....................... :....................................................................................................................... 16
_k WARNING: Read and understand all instructions.
Failure tofollow all instructionslisted below, may
result in electric shock, fire and/or serious personal
injury.
SAVE THESE INSTRUCTIONS
Work Area
• Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you
to lose control.
Electrical Safety
Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a
risk of fire when used with another battery. Use battery
only with charger listed.
MODEL BATTERY PACK CHARGER
973.111350 Item No.9-11013 Item No. _-11012
(981480-001) (981481-001)
Use battery operated tool only with specifically
designated battery pack. Use of any other batteries
may create a risk of fire. Use only with battery pack
listed.
Personal Safety
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inatten-
tion while operating power tools may result in serious
personal injury.
• Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
• Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery
pack. Carrying tools with your finger on the switch or
inserting the battery pack into a tool with the switch on,
invites accidents.
• Remove adjusting keys or wrenches before turn-
ing the tool on. A wrench or a key that is left attached
to a rotating part of the tool may result in personal
injury.
• De net overreach. Keep proper footing and bal-
ance at all times, Proper footing and balance enables
better control of the tool in unexpected situations. Do
not use on a ladder or unstable support.
• Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
2
Page 3
Tool Use and Care
• Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
• Do not force tool. Use the correct tool for your
application. The correct tool will do the job better and
safer at the rate for whicl_it is designed.
• Do not use tool if switch does not turn it on or off.
A tool that cannot he controlle_ with the switch is
dangerous and must be repaired.
• Disconnect battery pack from tool or place the
switch in the locked or off position before making
any adjustments, changing accessories, or storing
the tool. Such preventive safety mepsures reduce risk
of starting the tool accidentally.
• Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools, with sharp
cutting edges are less likely to bind and are easier to
control.
• Check for misalignment or binding of moving
_parts, breakage of parts, and any other condition
that may affec_ the tool's operation. If damaged,
have the tool serviced before using. Many accidents
a_e caused by:poorly maintained tools.
• Use only accessories that are recommended by
the manufacturer for your model. Accessories that
may be suitable for one tool, may create a risk of injury
when used on another tool.
Service
Tool service must be performed only by qualified
repair personnel. Service or;maintenance performed
by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replace-
ment parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructionsmay create a
risk of shock or injury.
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden
wiring. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
Additional Rules For Safe Operation
Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to
this tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gage size (A.W.G.) of at least 16 is
recommended for an extension cord 100 feet or less
in length. A cord exceeding 100 feet is not recom-
mended. If in doubt, use the nextheavier gage. The
smaller the gage number, the heavier the cord. An
undersized cord will cause a drop in linevoltage result-
ing in loss of power and overheating.
Important Rules for Battery Tools
• Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when chang-
ing accessories. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
• Do not place battery tools or their batteries near
fire or heat. They may explode. Following this rule
will reduce the risk of electric shock, fire, or serious
personal injury.
,_ WARNING: Batteries vent hydrogen gas and can
explode in the presence of a source of ignition, such as
a pilot light. To reduce the risk of serious injury, never
use any cordless product in the presence of open
flame. An exploded battery can propel debris and
chemicals. If exposed, flush with water immediately.
• Do not charge battery tool in a damp or wet
location. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
• For best results, your battery tool should be
charged in a location where the temperature is
more than 50°F but less than 100°F. Do not store
outside or in vehicles.
• Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
3
Page 4
_1, WARNING: A damaged battery is subject to
explosion. To avoid serious personal injury, properly
dispose of a damaged battery.
Important Safety Instructions For Charger
• Save these instructions. This manual contains
important safety and operating instructions for
charger item num bor 9-11012 (981481-001 ). Follow-
ing this rule will reduce'the risk of electric shock, fire,
or serious personal injury
• Before using battery charger, read all instructions
and cautionary markings in this manual, on
battery charger, and product using battery
charger. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
• TO reduce risk of injury, charge only nickel-
cadmium and nickel metal hydride type recharge-
able batteries. Other types of batteries may burst
causing personal injury and damage. Following this
rule will reduce the risk of electric shock, fire, or
serious personal injury.
• Do not expose charger to rain or snow. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
• Use of an attachment not recommended or sold
by the battery charger manufacturer may result in
a risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
• To reduce risk of damage to charger body and
cord, pull by charger plug rather than cord when
disconnecting charger. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
• Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress. Following this rule will reduce
the risk of serious personal injury.
• An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug o! extension cord are the
same number, Size and shape as those of
plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Cord Length (Feet) 25' 50' 100'
Cord Size (AWG) 16 16 16
Note: AWG = American Wire Gage
• Do not operate charger with a damaged cord or
plug. If damaged, have replaced immediately by a
qualified serviceman. Following this rule will reduce
the risk of electric shock, fire, or serious personal
injury.
• Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it'to a qualified serviceman. Following
this rule will reduce the risk of electric shock, fire, or
serious eersonal injury.
• DO not disassemble charger; take it to a qualified
serviceman when service or repair is required.
Incorrect reassembly may result in a risk of
electric shock or fire. Following this rule will reduce
the risk of electric shock, fire, or serious personal
injury.
• To reduce the risk of electric shock, unplug
charger from outlet before attempting any mainte-
nance or cleaning. Turning off controls will not
reduce this risk. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
• Do not use charger outdoors. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
Disconnect charger from power supply when not
in use. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
A_. DANGER: RISK OF ELECTRIC SHOCK. DO NOT
TOUCH UNINSULATED PORTION OF OUTPUT
CONNECTOR OR UNINSULATED BATTERY
TERMINAL.
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them
these instructions also. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
_I, WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
4
Page 5
SYMBOLS
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
min Minutes T_me
"%, Alternating Current Type or a characteristic of current
--= Direct Current Type or a characteristic of current
no No Load Speed ' Rotational speed, at no load
.../rain Revolutions or Reciprocation Per Minute Revolutions, strokes,
surface speed, orbits etc. per minute
,_ Safety Alert Symbol Indicates danger, warning or caution.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and
the explanations with them, deserve your careful attention and understanding. The safety warnings do
not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for
proper accident prevention measures.
SYMBOL MEANING
A
,a,
A
,a,
SAFETY ALERT SYMBOL:
Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs.
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
CAUTION: Failure to obey a safety warning may result in property damage or personal injury to
yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock
and personal injury.
It means attention!!! Your safety is
involved.
NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.
SAVE THESE INSTRUCTIONS
Page 6
KNOW YOUR DRILL-DRIVER
See Figure 1.
Before attempting to use any tool, familiarize yourself with
all operating features and safety requirements.
WRIST STRAP
A wrist strap is provided to reduce the chances of drop-
ping your drill-driver. Plac_one hand through the wrist
strap when carrying tool.
ADJUSTMENTRING
_ SCREWDRIVERBITS
KEYLESSCHUCK
BATrERYPACK
BATTERY REVERSE
CHARGER SELECTOR
SPECIFICATIONS:
Chuck Capacity
Motor
Charger Rating
No Load Speed
Switch
Charge Rate
Maximum Torque
TORQUE
3/8 in.
14.4 Volt DC
120 Volts, 60 Hz, AC Only
0 - 6OORPM
Variable Speed - Reversible
10 -12 Hours
100 in. Ibs.
FORWARD
SWITCH
TRIGGER
SIT
CHARGING
STAND
RED
LIGHT
BATTERYPACK
SHOWNINTOOL
,_ WARNING: If any parts are missing, do not operate tool until the missing parts are replaced. Failure to do so could
result in possible serious personal injury.
,_ WARNING:
WRISTSTRAP
Fig. 1
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety glasses with side shields, available at Sears
Retail Stores. Always wear eye protection which is marked to comply with ANSI Z87.1.
6
Page 7
_i WARNING" Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
_i, WARNING: Do not allow familiarity with your drill-
driver to make you careless. Remember that a
careless fraction of a ,s_l_ond_Ssufficient to inflict
severe injury.
CHARGING BATTERY PACK
The battery pack for this tool has been shipp.ed in a low
charge condition to prevent possible problems. Therefore,
you should charge it overnight prior to use.
Note: Batteries will not reach full charg_ the first time they
are charged. Allow several cycles (drilling followed by
recharging) for them to become fully charged.
TO CHARGE
• Charge battery pack only with the charger and
charging stand provided.
• Make sure power supply is normal household
voltage, 120 volts, 60 Hz, AC only.
• Connect charger to power supply.
• Place battery pack in charging stand. Align raised rib
on battery pack with groove in charging stand.
See Figure 1.
• Press down on battery pack to be sure contacts on
battery pack engage properly with contacts in charging
stand.
• When properly connected, the red light on charging
stand will turn on.
• Note: If charger does not charge battery pack, return
battery pack, charger and charging stand to your nearest
Sears Repair Center for electrical check.
• After normal usage, a minimumof 10 hours is required
to recharge a completely discharged tool.
• The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
• Do not place charger in an area of extreme heat or
cold. It will work best at normal room temperature.
• When batteries become fully charged, unplug charger
from power supply.
IMPORTANTINFORMATIONFOR RECHARGING
HOT BATTERIES
When using your drill-driver continuously, the batteries in
your battery pack will become hot. You should let a hot
battery pack co_)lGown for approximately 30 minutes
before attempting to recharge.
Note: This situation only occurs when continuous use of
your Grill causes the batteries to become hot. It does not
occur under normal circumstances. Refer to "CHARGING
BATTERY PACK" for normal recharging of batteries. If
the charger does not charge your battery pack under
normal circumstances, return both the battery pack and
charger to your nearest Sears repair center for electrical
check.
SWITCH
See Figure 2.
To turn your drill ON, depress the switch trigger. To turn it
OFF, release the switch trigger.
FORWARD/REVERSE
SELECTOR
CENTERPOSITION
(LOCK)
SWITCH
TRIGGER Fig. 2
VARIABLE SPEED
This tool has a variable speed switch that delivers higher
speed and torque with increased trigger pressure. Speed
is controlled by the amount of switch trigger depression.
Note: You might hear a whistling or ringing noise from the
switch during use. Do not be concerned, this is a normal
part of the switch function.
SWITCH LOCK
See Figure 2.
The switch trigger can be locked in the OFF position. This
feature can be used to prevent the possibility of accidental
starting when not in use. To lock switch trigger, place the
direction of rotation selector in center position.
WARNING: Battery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
Page 8
REVERSIBLE
See Figure 3.
This tool has the feature of being reversible. The direction
of rotation is controlled by a selector located above the
switch trigger. With the drill held in normal operating
position, the direction of rotation selector should be
positioned to the left of the switch for drilling. The drilling
direction is reversed when'jhe selector is to the right of
the switch. When the selector is in center position, the
switch trigger is locked.
BATTERYPACK
CENTERPOSITION
(LOCK)
f SELECTOR
FORWARD
Fig, 3
,_ CAUTION: To prevent gear damage, always allow
chuck to come to a complete stop before changing
the direction of rotation.
To stop, release switch trigger and allow the chuck to come
to a complete stop.
TO INSTALL BATTERY PACK
See Figure 4.
• Lock switch trigger on your drill by placing the
direction of rotation selector in center position. See
Figure 2.
• Place battery pack in your drill. Align raised rib inside
drill with groove on battery pack. See Figure 4.
LATCHES
\
DEPRESSLATCHESTO
RELEASEBATTERYPACK
• Make sure the latches on each side of your battery
pack snap into place and battery pack is secured in
drill before beginning operation.
,_k CAUTION: When placing battery pack in your drill,
be sure raised rib inside drill aligns with groove on
battery pack and latches snap in place properly.
Improper assembly of battery pack can cause
damage to internal components.
TO REMOVE BA'R'ERY PACK
• Lock switch trigger on your drill by placing the
direction of rotation selector in center position. See
Figure 2.
• Locate latches on end of battery pack and depress to
release battery pack from your drill. See Figure 4.
• Remove battery pack from your drill.
Fig. 4
8
Page 9
KEYLESS CHUCK _
See Figure 5.
Your drill has a keyless chuck. As the name implies, you can
hand tighten or release drill bits in the chuck jaws. Grasp and
hold the collar of the chuck with one hand. Rotate the chuck
body with your other hand. The arrows on the chuck indicate
which direction to rotate the chuck body in order to LOCK
(tighten) or UNLOCK (releas_the drill bit.
UNLOCK
DRILLBIT
CHUCKJAWS
(RELEASE) CHUCK
BODY
INSTALLING BITS
See Figure 7.
• Lock switch trigger on your drill by placing the direc-
tion of rotation selector in center position. See Figure
2.
• -Open or close chuck jaws to a point where the open-
ing is slightly larger than the bit size you intend to use.
Also, raise the front of your drill slightly to keep the bit
from falling ou! of the chuck jaws.
• Insert drill bit straight into chuck the full length of the
jaws as shown in figure 7.
• Tighten the chuck jaws on drill bit.
DRILLBIT CHUCKBODY
LOCK
(TIGHTEN)
CHUCK /
COLLAR
Fig. 5
,_ WARNING: Do not hold chuck body with one hand
and use power of the drill to tighten chuck jaws on
drill bits. Chuck body could slip in your hand or your
hand could slip and come in contact with rotating drill
bit. This could cause an accident resulting in serious
personal injury.
BIT STORAGE
See Figure 6.
When not in use, bits provided with your drill can be
placed in the storage area located at the bottom of your
drill as shown in figure 6.
SCREWDRIVER
BIT
SCREWDRIVER
BIT
CHUCKJAWS
CHUCKCOLLAR
RIGHT Fig. 7
To tighten the chuck jaws on drill bit; grasp and hold
the collar of the chuck with one hand, while rotating
the chuck body with your other hand.
Note: Rotate the chuck body in the direction of the
arrow marked LOCK to tighten chuck jaws.
Do not use a wrench to tighten or loosen the chuck
jaws.
,_WARNING: Make sure to insert drill bit straight into
chuck jaws. Do not insert drill bit into chuck jaws at
an angle and then tighten, as shown in figure 8. This
could cause drill bit to be thrown from drill, resulting
in possible serious personal injury or damage to the
chuck.
BIT
STORAGE
AREA
Fig. 6 Fig. 8
9
Page 10
REMOVING BITS
See Figure 7.
• Lock switch trigger or your drill by placing the direction
of rotation selector in center position. See Figure 2.
• Loosen the chuck jaws from drill bit.
• To loosen: grasp and hold the collar of the chuck with
one hand, while rotatin_ chuck body with your other
hand. Note: Rotate ch_ck body in the direction of the
arrow marked UNLOCK to J.oosenchuck jaws.
• Do not use a wrench to tighten or loosen the chuck
jaws.
• Remove drill bit from chuck jaws.
ADJUSTABLE TORQUE CLUTCH
See Figure 9.
Your drill is equipped with an adjustable torque clutch for
driving different types of screws into different materials.
The proper setting depends on the type of material and
the size of screw you are using.
TO ADJUST TORQUE
• Identify the twenty four torque indicator settings
located on the front of your drill. See Figure 9.
• Rotate adjusting ring to the desired setting.
• 1 - 4 For driving small screws.
5 - 8 For driving screws into soft
material.
• 9 o 12 For driving screws into soft and hard
materials.
• 13 - 16 For driving screws in hard wood.
• 17 - 20 For driving large screws.
• 21 - _,11 For heavy drilling.
TODECREASE ADJUSTING
TORQUE RING
DRILLING
See Figure 10.
Fig. 10
When drilling hard smooth surfaces use a center punch to
mark desired hole location.This will prevent the drill bit from
slipping off center as the hole is started. However, the low
speed feature allows starting holes without center punching
if desired. To accomplish this, simply operate your drill at a
low speed until the hole is started.
The material to be drilled should be secured in a vise or with
clamps to keep itfrom turning as the drill bit rotates.
Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.
Move the drill bit into the workpiece applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
TOINCREASE
TORQUE Fig. g
,_ WARNING: Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
,_ WARNING: Be prepared for binding or bit
breakthrough. When these situations occur, drill has
a tendency to grab and kick opposite to the direction
of rotation and could cause loss of control when
breaking through material. If not prepared, this loss
of control can result in possible serious injury.
When drilling metals, use a light oil on the drill bit to keep
it from overheating. The oil will prolong the life of the bit
and increase the drilling action.
If the bit jams in workpiece or if the drill stalls, release
switch trigger immediately. Remove the bit from the
workpiece and determine the reason for jamming.
10
Page 11
CHUCK REMOVAE
See Figures 11, 12, and 13.
The chuck must be removed in order to use some
accessories. To remove:
• Lock switch trigger or your drill by placing the
direction of rotation selector in center position• See
Figure 2.
• Insert a 5/16 in. or larger _ex key into the chuck of your
drill and tighten the chuck jawssecurely.
• Tap the hex key sharply with a mallet in a clockwise
direction. See Figure 11. This will loosen the screw in
the chuck for easy removal•
MALLET
CHUCK
JAWS
\
Insert hex key in chuck and tighten chuck jaws se-
curely. Tap sharply with a mallet in a counterclockwise
direction. This will loosen chuck on the spindle. Itcan
now be unscrewed by hand. See Figure 13.
HEXKEY
Open chuck jaws and remove hex key. Remove the
chuck screw by turning it in a clockwise direction. See
Figure 12.
Note: The screw has left hand threads.
SCREWDRIVER
Fig. 11
Fig. 13
TO RETIGHTEN A LOOSE CHUCK
The chuck may become loose on spindle and develop a
wobble• Periodically check chuck screw for tightness.
To tighten, follow these steps:
• Lock switch trigger on your drill by placing the
direction of rotation selector in center position. See
Figure 2.
• Open the chuck jaws.
• Insert hex key into chuck and tighten chuck jaws
securely. Tap hex key sharply with a mallet in a
clockwise direction. This will tighten chuck on the
spindle.
• Open the chuck jaws and remove hex key.
• Tighten the chuck screw•
Note: The chuck screw has left hand threads•
Fig. 12
11
Page 12
,_ WARNING: When servicing, use only identical
Craftsman replacement pads. Use of any other part
may create a hazard or cause product damage.
Avoid using solvents when cleaning plastic pads. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
_i WARNING: Do not let brake fluids,a{anytime
gasoline, petroleum-based-products, penetrating oils,
etc. come in contact with plastic pads. They contain
chemicals that can damage, weaken or destroy
plastic.
Do not abuse power tools. Abusive practices can damage
tool as well as workpiece.
BA'R'ERIES
Your drill's battery pack is equipped with 12 nickel- •
cadmium rechargeable batteries. Length of service from
each charging will depend on the type of work you are
doing. •
The batteries in this tool have been designed to provide
max{mum trouble free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack •
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry,
could result in a serious burn.
To obtain the longest possible battery life, we suggest the
following:
Only the parts shown on parts list, page 15, are intended
to be repaired or replaced by the customer. All other parts
should be replaced by a qualified service technician at an
authorized service facility.
Awe"a?e" c", e:3o::tn3;te o tt ;.o;St::,wOrh
this tool. Any such alteration or modification is
"misuse and could result in a hazardous condition
leading to possible serious personal injury.
Store and charge your batteries in a cool area.
Temperatures above normal room temperature will
shorten battery life.
Never store batteries in a discharged condition.
Recharge them immediately after they are
discharged.
All batteries gradually lose their charge. The higher
the temperature the quicker they lose their charge. If
you store your tool for long periods of time without
using it, recharge the batteries every month or two.
This practice will prolong battery life.
To preserve natural resources, please
recycle or dispose of batteries properly.
This product contains nickel-cadmium
batteries. Local, state or federal laws
may prohibit disposal of nickel-cadmium
batteries in ordinary trash.
Consult your local waste authority for information
regarding available recycling and/or disposal options.
BATTERY PACK REMOVAL AND PREPARATION
FOR RECYCLING
_i WARNING: Upon removal, cover the battery pack's
terminals with heavy duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body pads as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
12
Page 13
ThefollowingrecomrnendedaccessoriesarecurrentlyavailableatSearsRetailStores.
• 6-Pc.ExtraLengthMagnitePowerBitSet • HighSpeedBits(ForWoodorMetal)...3/4in.Max.
• 30-Pc.PowerScrewdriver/NutdriverSetandCase • KeylessChuck(ItemNo.9-20988)
• 17-Pc.PowerScrewddver/NutdriverSetandCase
,_ WARNING: The use.Of attachments or accessories not listed might be hazardous.
WARRANTY
FULL ONE YEAR WARRANTY ON CRAFTSMAN 318 in. CORDLESS DRILL-DRIVER
If this CRAFTSMAN3/8 in. Cordless Drill]Driver fails to give complete satisfaction within one year from the date of pur-
chase, RETURN IT TO THE NEARESTtSEARS STORE OR SEARS SERVICE CENTER IN THE UNITED STATES,
and Sears will repair it, free of charge.
If this CRRFTSMIIN 3/8 in. Cordless Drill-Driver is used for commercial or rental purposes, this warranty applies for only
g0 days from the date of purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817 WA, Hoffman Estates, IL 60179
13
Page 14
14
Page 15
CRAFTSMAN 318 in., 14.4 VOLT CORDLESS DRILL-DRIVER - MODEL NO. 973.111350
number in all correspondence regarding your 3/8 in., 14.4 VOLT CORDLESS DRILL-DRIVER or
The model number will be found on a plate attached to the motorhousing. Always mention the model I
when ordering repair parts.
SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS
2
m
I
Key Part
No. Number
1 616478-003
2 973094-001
3 * Item No. 9-11013
4 * Item No. 9-11012
5 3051757-01
972000-923
4
PARTS LIST
Description Quan.
Screw (Special) ................................................ 1
Chuck (Item No. 9-20988) ................................ 1
Battery Pack (981480-001) .............................. 1
Charger w/Charging Stand (981481-001) ........ 1
Carrying Case - Not Shown ............................ 1
Owner's Manual
• I
* Can Be Purchased Through RSOS (Retail Special Order System)
15
Page 16
Get it fixed, at your home or ours!
For repair of major brand appliances in your own home...
no matter who made it, no matter who sold it!
1'800-4-MY-HOME sMAnytime, day or night
(1-800-469-4663)
www.sears.com
To bring in produ_s such as vacuums, lawn equipment and electronics
for repair, call for the location of your nearest Sears Parts & Repair Center.
1-800-488-1222 Anytime, day or night
www.sears.com
For the replacement parts, accessories and owner's manuals
that you need to do-it-yourself, call Sears PartsDirect SM!
1-800-366,PART 6 a.m. - 11 p.m. CST,
(1-800-366-7278) 7 days a week
www.sears.com/partsdirect
To purchase or inquire about a Sears Service Agreement:
1-800-827-6655
7 a.m. - 5 p.m. CST, Mon.- Sat.
Para pedir servicio de reparaciSn a domicilio,
y para ordenar piezas con entrega a domicilio:
1-888-SU-HOGAR sM
(1-888o784:6427)
( S£ARS 1
H°meCentrar° J
Au Canada pour service en fran£ais:
1-877-LE-FOYER sM
(1-877-533-6937)
@ Registered Trademark / TM Trademark of Sears, Roebuck and Co
© Sears, Roebuck and Co ® Marca Registrada / T-_Marca de Fabrica de Sears, Roebuck and Co.
Loading...