![](/html/be/bed2/bed24e138b9a212bd4ee5e75513d406805cd68692d9568fc562c8c8c7f60d75f/bg1.png)
Instruction Manual
ICRRFTSMRN°I
40 Amp Motor
13 Inch Cutting Path/0 065 In Line
ELECTRIC WEEDWACKER ®
Model No
0944.511100
\ ,
• Safety
• Assembly
• Operation
• Maintenance
• Fran£ais
\'\
0®
Read and follow all Safety Rules and Operating
WARNING:
Instructions before first use of this product
For answers to your questions about this product:
Call 7 am-7 pm, Mon-Sat; Sun, 10 am-7 pm
• 1-800-235-5878 (Hours listed are Central Time)
Sears Canada, Inc, Toronto, Ontario M5B 2B8
530086232 1/10/02
![](/html/be/bed2/bed24e138b9a212bd4ee5e75513d406805cd68692d9568fc562c8c8c7f60d75f/bg2.png)
Warranty Statement 2 Parts Available 9
Safety Rules 2 Storage 10
Assembly 5 Troubleshooting Table 10
Operation 6
Maintenance 8 French 11
Service & Adjustments 9 Parts Ordering Back Cover
TWO (2) YEAR LIMITED WARRANTY ON CRAFTSMAN ELECTRIC
WEEDWACKER _ LINE TRIMMER
For two (2) years from tile date of purchase, Sears Canada, Inc., will repair or
replace free of charge, at Sears option, parts which are defective as a result of
material or workmanship.
COMMERCIAL OR RENTAL USE:
Warranty is void if the electric trimmer is used for commercial or rental purposes.
This warranty does not cover wear items such as line and spool.
WARRANTY SERVICE ISAVAILABLE BY RETURNING THE ELECTRIC TRIMMER TO THE
NEAREST SEARS SERVICE CENTRE/DEPARTMENT IN CANADA. THIS WARRANTY AP-
PLIES ONLY WHILE THIS PRODUCT IS IN USE IN CANADA.
This warranty is in addition to any statutory warranty and does not exclude or limit
legal rights you may have but shall run concurrently with applicable provincial
legislation. Furthermore, some provinces do NOT allow limitations on how long an
implied warranty will last, so the above limitations may not apply to you.
Sears Canada, Inc., Toronto, Ontario MSB 2B8
4t_WARNING: When using electric
gardening appliances, basic safety
precautions must always be followed
to reduce the risk of fire, electric
shock, and serious injury. Read and
follow all instructions.
SAFETY INFORMATION
ON THE UNIT
This power unit can be dangerous!
Operator is responsible for following
the warnings and instructions in this
manual and on the unit. Read entire
instruction manual before using unit!
Be thoroughly familiar with the con-
trois and the proper use of the unit.
Restrict the use of this unit to persons
who read, understand, and follow unit
and manual warnings and instruc-
tions. Never allow children to operate
this unit. Close attention is necessary
when used near children.
_DANGER: Never use blades or
flailing devices. Unit is designed for line
trimmer use only= Use of any other ac-
cessories or attachments will increase
the risk of injury.
000
n WARNING: Trimmer line throws
objects violently. You and others can
be blinded/injured. Wear safety
glasses, boots, and leg protection.
Keep body parts clear of rotating line.
Safety Glasses or similar eye protection
Boots
Keep children, bystanders, and ani-
mals 50 feet (15 meters) away. If ap-
proached stop unit immediately.
If situations occur which are not cov-
ered in this manual, use care and
good judgement. If you need assis-
tance, call 1-800-235-5878.
2
![](/html/be/bed2/bed24e138b9a212bd4ee5e75513d406805cd68692d9568fc562c8c8c7f60d75f/bg3.png)
OPERATORSAFETY
• Dressproperly.Alwayswearsafety
glassesorsimilareye protection
when operating, or performing main-
tenance on your unit. (Safety
glasses are available.) Always wear
face or dust mask if operation is
dusty. Always wear heavy, long
pants, long sleeves, boots, and
gloves. Do not go barefoot or wear
sandals.
• Secure hair above shoulder length.
Secure or remove loose clothing
and jewelry or clothing with loosely
hanging ties, straps, tassels, etc.
They can be caught in moving parts.
• Being fully covered also helps pro-
tect you from debris and pieces of
toxic plants thrown by spinning line.
• Stay Alert. Do not operate unit when
you are tired, ill, upset or under in-
fluence of alcohol, drugs, or medica-
tion. Watch what you are doing; use
common sense.
• Avoid unintentional starting of the
unit. Never carry unit with your fin-
ger on the switch. Be sure the
switch is in the OFF position and
never touch the switch when con-
necting extension cord.
ELECTRICAL SAFETY
_IWARNING: Avoid a dangerous
environment. To reduce the risk of
electrical shock, do not use in rain, in
damp or wet locations, or around
swimming pools, hot tubs, etc. Do not
expose to snow, rain, or water to avoid
the possibility of electrical shock.
• Use a voltage supply as shown on
unit.
• Avoid dangerous situations. Do not
use in the presence of flammable
liquids or gases to avoid creating a
fire or explosion and/or causing
damage to unit.
• To reduce the risk of electrical
shock, this equipment has a polar-
ized plug (one blade is wider than
the other) and will require the use of
a polarized extension cord. The ap-
pliance plug will fit into a polarized
extension cord only one way. If the
plug does not fit fully into the exten-
sion cord, reverse the plug. If the
plug still does not fit, obtain a correct
polarized extension cord. A polar-
ized extension cord will require the
use of a polarized wall outlet. This
plug will fit into the polarized wall
outlet only one way. If plug does not
fit fully into the wall outlet, reverse
the plug. If it still does not fit, contact
a qualified electrician to install the
proper wall outlet. Do not change
the equipment plug, extension cord
receptacle, or extension cord plug in
any way.
• To reduce risk of electrical shock,
use extension cords specifically
marked as suitable for outdoor ap-
pliances having electrical rating not
less than the rating of unit. Cord
must be marked with the suffix "W".
Make sure your extension cord is in
good condition. Inspect extension
cord before use and replace if dam-
aged. Do not use a damaged cord.
Cord insulation must be intact with
no cracks or deterioration. Plug
connectors must be undamaged.
An undersized extension cord will
cause a drop in line voltage resulting
in loss of power and overheating. If
in doubt, use the next heavier
gauge. The lower the gauge num-
ber, the heavier the cord (see SE-
LECT AN EXTENSION CORD in the
OPERATION section).
• Do not use multiple cords.
• Do not abuse cord. Never carry the
unit by the extension cord or yank
extension cord to disconnect unit.
• Use cord retainer to prevent discon-
nection of extension cord from unit
and possible damage to the unit due
to plug movement. See ATTACH THE
EXTENSION CORD TO YOUR TRIM-
MER in the OPERATION section.
• Do not use the unit if the switch
does not turn the unit on and off
properly. Repairs to the switch must
be made by your Sears Service
Centre.
• Keep the extension cord clear of op-
erator and obstacles at all times. Do
not expose cords to heat, oil, water,
or sharp edges.
• To avoid the possibility of electric
shock, avoid body contact with any
grounded conductor, such as metal
fences or pipes.
• Ground Fault Circuit Interrupter
(GFCI) protection should be pro-
vided on circuit or outlet to be used.
Receptacles are available having
built-in GFCI protection and may be
used for this measure of safety.
UNIT SAFETY
• Inspect unit before use. Replace
damaged parts. Make sure all han-
dles, guards, and fasteners are in
place and securely fastened. Parts
3
![](/html/be/bed2/bed24e138b9a212bd4ee5e75513d406805cd68692d9568fc562c8c8c7f60d75f/bg4.png)
thataredamagedmustberepaired
orreplacedbyaSearsService
CentreTheseincludeheadparts
thatarecracked,orchipped,
guards,andanyotherpartthatis
damaged.
• Donotrepairunityourself.
• Useonly0.065in.(1.65ram)diam-
eterrecommendedtrimmerline(see
SERVICEANDADJUSTMENTS).Nev-
erusewire,rope,string,etc.
• Usespecifiedtrimmerspool.Make
surespoolisproperlyinstalledand
allpartsaresecurelyfastened.
• UseonlyCraftsmanreplacement
partsandaccessoriesasrecom-
mended.
CUTTINGSAFETY
• Inspect area to be cut. Remove ob-
jects (rocks, broken glass, nails,
wire, string, etc.) which can be
thrown or become entangled in cut-
ting head.
• Do not overreach or stand on unsta-
ble support. Keep firm footing and
balance.
• Keep the cutting head below waist
level. Do not raise handles above
your waist. Cutting head can come
dangerously close to your body.
• Keep away from cutting head and
spinning line.
• Use unit properly. Use only for trim-
ming, edging, scalping, and mow-
ing. Do not force unit. It will do the
job better and with less risk of injury
at the rate for which it was designed.
• Use only in daylight or in good artifi-
cial light.
MAINTENANCE SAFETY
_IWARNING: Disconnect unit from
the power supply before performing
maintenance, or when changing trim-
mer line.
• Maintain unit according to recom-
mended procedures. Keep cutting
line at proper length. Follow instruc-
tions for changing trimmer line.
• Have all service and maintenance
not explained in this manual per-
formed by a Sears Service Centre to
avoid creating a hazard.
• Never douse or squirt the unit with
water or any other liquid. Clean unit
and labels with a damp sponge.
Keep handles dry, clean, and free
from oil and grease.
• Keep the air vents clean and free of
debris to avoid overheating the mo-
tor. Clean after each use.
TRANSPORTING AND STORAGE
• Stop the unit and disconnect the
power source when not in use.
• Carry the unit with motor stopped.
• Store the unit so the line limiter
blade (on underside of shield) can-
not cause injury.
• Store unit indoors in a high, dry
place out of the reach of children.
Store unit unplugged.
• Do not hang unit so that the trigger
switch is depressed.
DOUBLE INSULATION
CONSTRUCTION
This unit is double insulated to help
protect against electric shock. Double
insulation construction consists of two
separate "layers" of electrical insula-
tion instead of grounding.
Tools built with this insulation system
are not intended to be grounded. No
grounding means is provided on this
unit, nor should a means of grounding
be added to this unit. As a result, the
extension cord used with your unit can
be plugged into any standard 120 volt
electrical outlet.
Safety precautions must be observed
when operating any electrical tool.
The double insulation system only
provides added protection against in-
jury resulting from an internal electrical
insulation failure.
_, WARNING: All electrical repairs
to this unit, including housing, switch,
motor, etc., must be diagnosed and
repaired by qualified service person-
nel. Replacement parts for a double
insulated appliance must be recom-
mended by the manufacturer. A
double insulated appliance is marked
with the words "double insulation" or
"double insulated". The symbol
(square within a square) [] may also
be marked on the appliance. Failure
to have the unit repaired by qualified
service personnel can cause the
double insulation construction to be-
come ineffective and result in serious
injury.
SAVE THESE INSTRUCTIONS
![](/html/be/bed2/bed24e138b9a212bd4ee5e75513d406805cd68692d9568fc562c8c8c7f60d75f/bg5.png)
CARTON CONTENTS
Check carton contents against the fol-
lowing list.
Model 0944.511100
• Trimmer
• Shield
Examine parts for damage. Do not
use damaged parts.
NOTE: If you need assistance or find
parts missing or damaged, call
1-800-235-5878.
ASSEMBLY
_WARNING: If received as-
sembled, review all assembly steps to
ensure your unit is properly as-
sembled and all fasteners are secure.
ADJUSTING ASSIST HANDLE
1. Loosen wing nut on handle.
2. Rotate the handle on the tube to
an upright position; place in a
comfortable position and retighten
wing nut.
\
ATTACHING THE SHIELD
_WARNING: The shield must be
properly installed. If shield is not prop-
erly installed, damage to unit (includ-
ing motor failure) will result. The shield
provides partial protection to the oper-
ator and others from the risk of thrown
objects. Your unit is equipped with a
line limiter blade, which cuts excess
line to the proper length while running.
The line limiter blade (on underside of
shield) is sharp and can cut you.
NOTE: Edge guide must be posi-
tioned on shield prior to installation on
motor housing (see following illustra-
tion).
Edge Guide
Shield
1. Hold shield at angle to the trimmer
motor housing. Align the front
locking tab of the shield with the
front notch of the motor housing
(see illustration below).
2. Move shield toward motor hous-
ing, ensuring trimmer head passes
through opening in shield without
catching on shield locking tabs.
3. Tilt front of the shield towards front
notch of motor housing. Push
front locking tab of the shield into
the front notch of the motor hous-
ing. An audible snap must be
heard. Ensure the cutting head re-
mains free to rotate and the line is
not caught between the shield and
the motor housing.
4. Push back of the shield toward the
motor housing as illustrated until
the rear locking tabs snap secure-
ly into the rear notches. Make
sure the shield is securely at-
tached to the motor housing and is
assembled to the unit as shown on
the front cover of this manual.
Rear Front Locking Tab
Locking Front
Tabs Motor
Trimmer
Housing
Notches
nmmer
Head
CAUTION: Sharp line limiter blade
![](/html/be/bed2/bed24e138b9a212bd4ee5e75513d406805cd68692d9568fc562c8c8c7f60d75f/bg6.png)
KNOW YOUR TRIMMER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT. Compare the illustrations with your unit to familiarize yourself with the loca-
tion of the various controls and adjustments. Save this manual for future refer-
ence.
Trigger Switch
Assist Handle
? LJ _ ......
Cord:J'/
Retainer /
RECESSED PLUG
The RECESSED PLUG is where you at-
tach your extension cord to the unit.
TRIGGER SWITCH
The TRIGGER SWITCH is used to turn
on the unit. Squeeze the trigger switch
to operate the unit. Release to stop.
LINE LIMITER BLADE
The LINE LIMITER BLADE cuts the cut-
ting line to the proper cutting length.
ASSIST HANDLE
The ASSIST HANDLE is used to help
hold and guide the unit.
OPERATING INSTRUCTIONS
Use only a voltage supply as specified
on your unit.
SELECT AN EXTENSION CORD
Extension Cord Gauge Chart
Length of Cord Gauge
25 Ft. (7.5 m) 18 Gauge
50 Ft. (15 m) 16 Gauge
100 Ft. (30 m) 16 Gauge
Extension cords are available for this
unit at Sears.
Recessed
Plug
Twist and Edge Button
Motor Housing
j Edge Guide
Air Vents ",,_
Debt s She d _/_:;;_" TriY_mmerHead
_ with 0,065 in,
Line Limiter Blade
TRIMMER HEAD
The TRIMMER HEAD holds the cutting
line and rotates during operation.
TWIST AND EDGE BUTTON
The TWIST AND EDGE BUTTON is used
to twist the lower portion of the unit
into an edging position.
EDGE GUIDE
The EDGE GUIDE protects the unit
from contacting the ground during
edging.
ATTACH THE EXTENSION
CORD TO YOUR TRIMMER
Loop your extension cord through the
handle and around the hook as
shown. Insure the plug and cord are
firmly and fully engaged.
Cord Retainer
Trimmer Line
Extension Cord