Craftsman 937.256541 Owner's Manual

MODEL NU 937.256541 OWNER'S MANUAL

° Assembly ° Operation ° Customer Responsibilities

Service and Adjustments

° Repair Parts

CAUTION:Read and follow all safety rules and instructions before operating this equipment.

FOR CONSUMER ASSISTANCE HOT LINE, CALL THIS TOLL FREE NUMBER: t-800-659_5917

, , i ,

SAFETY RULES

Safe Operation Practices for Ride=On Mowers

IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH

1. GENERAL OPERATION

• Read, understand, and follow a]f instructions in the manual and on the machine before starting.

• Only allow responsible adults, who are faro[tier with the instructions, to operate the machine,

• Clear the area of objects such as rocks, toys, wire, etc,, which could be picked up and thrown by the biade_

• Be sure the area is clear of other people before mowing Stop machine if anyone enters the area

= Never carry passengers

• Do not mow in reverse unless absolutely necessary Always took down and behind before and while backing,

° Be aware of the mower discharge direction and do not point

it at anyone, Do not operate the mower without either the entire grass catcher or the guard in place

= Slow down before turning . Never leave a running machine unattended Always turn off

blades, set parking brake, stop engine, and remove keys before dismounting

• Turn off blades when not mowing

• Stop engine before removing grass catcher or unclogging chute

- Mow only in daylight or good artificial light

• Do not operate the machine while under the influence of

alcohol or drugs

• Watch for traffic when operating near of crossing roadways=

• Use extra care when loading or unloading the machine into a trailer or truck.

II. SLOPE OPERATION

Slopes are a major factor related to loss-of-control and

tipover accidents, which can result in severe injury or

death,. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.

DO:

o Mow up and down slopes, not across

• Remove obstacles such as rocks, tree limbs, etc

• Watch for holes, ruts, or bumps: Uneven terrain could overturn the machine Tatf grass can hide obstacles

• Use slow speed Choose a low gear so that you will not have to stop or shift while on the slope

,, Follow the manufacturer's recommendations for wheel

weights or counterweights to improve stability.

• Use extra care with grass catchers or other attachments,, These can change the stability of the machine,

• Keep alt movement on the slopes slow and gtaduat. Do net make sudden changes in speed or direction.

• Avoid starting or stopping on a slope, If tires lose traction, disengage the blades and proceed sIowly straight down the slope

DO NOT:

= Do not turn on s]opes unless necessary, andthen, turn slowly

and gradually downhill, if possible_

° Do not mow near' drop-offs, ditches, or embankments., The

mower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in.

= Do not mow on wet grass, Reduced traction could cause

sliding,

o Do not try to stabilize the machine by putting your foot on the

ground°

• Do not use grass catcher on steep slopes

IlL CHILDREN

Tragic accidents can occur if the operator is not alert to the

presence of children° Children are often attracted to the machine and the mowing activity Never assume that

children will remain where you last saw them.

• Keep children out of the mowing area and under the watchful care of another responsible adult

. Be aled and turn machine off if children enter the area

• Before and when backing, look behind and down for small children

° Never carry chiIdren They may fall off and be seriously

injured or interfere with safe machine operation

• Never allow children to operate the machine.

- Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision

IV. SERVICE

• Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive

Use only an approved container Never remove gas cap or add fuel with the engine

running Allow engine to cool before refueling Do not smoke

Never refuel the machine indoors Never store the machine or fuel container inside where

there is an open flame, such as a water heater,

• Never run a machine inside a closed area.

= Keep nuts and bolts, especially blade attachment bolts, tight

and keep equipment in good condition

° Never tamper with safety devices. Check their proper

operation regularly,,

° Keep machine free of grass, leaves, or other debris build-up

Clean oil or fuel spillage. Allow machine to cool before storing

• Stop and inspect the equipment if you strike an object

Repair, if necessary, before restarting

• Never make adjustments or repairs with the engine running.

° Grasscatcher components are subject to wear, damage, and

deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer's recommended parts, when nec- essary.

• Mower blades are sharp and can cut Wrap the blade(s) or wear gloves, and useextra caution when servicing them.

o Check brake operation frequently. Adjust and service as

required.

Look for this symbol to point out important

safety precautions. It means CAUTION!!I BECOME ALERT!!! YOUR

SAFETY IS INVOLVED.

CAUTION: Always disconnect spark plug

wire and place wire where it cannot contact

spark plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs°

WARNING ,&

The engine exhaust from this product contains

chemicals known to the State of California to cause cancer, birth defects, or other reproduc-

tive harm.

i i

CONGRATULATIONS on your purchase of a Sears Tractor, It has been designed, engineered and manufac- tured to give you the best possible dependability and

performance.

Should you experience any problem you cannot easily

remedy, please contact your nearest Sears Authorized

Service Center/Department We have competent, well- trained technicians and the proper tools to sewice or repair

this tractor.

Please read and retain this manual, The instructions will

enable you to assemble and maintain your tractor properly.

Always observe the "SAFETY RULES"

MODEL NUMBER

SERIAL NUMBER

917.256541

DATE OF PURCHASE THE MODEL AND SERIAL NUMBERS WILL BEFOUND

ON A PLATE UNDER THE SEAT. YOU SHOULD RECORD BOTH SERIAL NUMBER AND

DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

MAINTENANCE AGREEMENT

A Sears Maintenance Agreement is available on this prod- uct. Contact your nearest Sears store for details,

CUSTOMER RESPONSIBILITIES

o Read and observe the safety rules.

• Follow a regular schedule in maintaining, caring for and using your tractor.

• Follow the instructions under "Customer Responsibili- ties" and "Storage" sections of this owner's manual.

PRODUCT SPECIFDCATtONS

HORSEPOWER: 15,0 GASOLINE CAPACITY 5 QUARTS

AND TYPE: UNLEADED REGULAR OfL TYPE (API-SF/SG): SAE 10W30 (above 32°F)

SAE 5W-30 (below 32_F)

OlL CAPACITY: Wi FILTER: 4 0 PINTS

W/O FILTER: 3.5 PINTS

SPARK PLUG: CHAMPION RC12YC (GAP: .040")

VALVE CLEARANCE: NOT ADJUSTABLE GROUND SPEED (MPH): FORWARD:

1st 1 1 2rid 1 5 3rd 23 4th 3 5 5th 4 4 6th 5 7

REVERSE: 1.7

TIRE PRESSURE: FRONT: 14 PSi

REAR: 10 PSi

CHARGING SYSTEM: 3 AMPS BATTERY

5 AMPS HEADLIGHTS

BATTERY: AMP/HR: 30

MIN. CCA: 240 CASE SIZE: U1R

BLADE BOLT TORQUE: 30-35 FT LBS

WARNING: This tractor is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-cov- ered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any), Ifa spark arrester is used, it should be maintained in effective working order by the operator

In the state of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws Federal laws apply on federal lands A spark arrester for the muffler is available through your nearest Sears Authorized Service Center/ Department (See REPAIR PARTS section of this manual).

LIMITED TWO YEAR WARRANTY ON CRAFTSMAN RIDING EQUIPMENT

For two (2) years from the date of purchase, if this Craftsman Riding Equipment is maintained, lubricated and tuned up according to the instructions in the owner's manual, Sears will repair or replace, free of charge, any parts found to be defective in material or workmanship,

This Warranty does not cover:

• Expendable items which become worn during normal use, such as blades, spark plugs, air cleaners, belts, etc

• Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps, or glass . Repairs necessary because of operator abuse, negligence, improper storage or accident or the failure to maintain the

equipment according to the instructions contained in the owner's manual

• Riding equipment used for commercia! or rental purposes

LIMITED 90 DAY WARRANTY ON BATTERY

For ninety (90) days from date of purchase, if any battery included with this riding equipment proves defective in material or

workmanship and our testing determines the battery will not hold a charge, Sears will replace the battery at no charge

IN-HOME WARRANTY SERVICE ON YOUR CRAFTSMAN RIDING EQUIPMENT IS AVAILABLE AT NO-CHARGE FOR 30 DAYS FROM THE DATE OF PURCHASE PLEASE CONTACT YOUR NEAREST SERVICE CENTER. AFTER 30 DAYS FROM THE DATE OF PURCHASE, WARRANTY SERVICE iS AVAILABLE BY TAKING YOUR CRAFTSMAN RIDING EQUIPMENT TO YOUR NEAREST SEARS SERVICE CENTER. (IN-HOME WARRANTY SERVICE WILL STILL BE AVAILABLE AFTER 30 DAYS FROM

THE DATE OF PURCHASE BUT A STANDARD TRIP CHARGE WtLL APPLY ) THIS WARRANTY APPLIES ONLY WHILE THIS

PRODUCT IS IN THE UNITED STATES,

This Warranty gives you specific legat rights, and you may also have other rights which may vary from state to state

SEARS, ROEBUCK AND CO., D/817 WA, HOFFMAN ESTATES, IL 60179

TABLE OF CONTENTS

SAFETY RULES ............................................................ 2

PRODUCT SPECIFICATIONS ...................................... 3

CUSTOMER RESPONSIBILITIES ..................... 3, 15-19

WARRANTY ................... ;.............................................. 3

TABLE OF CONTENTS ................................................. 4

INDEX ............................................................................ 4

TRACTOR ACCESSORIES .......................................... 5

ASSEMBLY ............................................................... 7-9

OPERATION .......................................................... 10-14

MAINTENANCE SCHEDULE ..................................... 15

SERVICE AND ADJUSTMENTS ........................... 20-25

STORAG E ................................................................... 26

TROUBLESHOOTING ........................................... 27-28

REPAIR PARTS - TRACTOR ................................ 30-47

REPAIR PARTS - ENGINE .................................... 48-53

PARTS ORDERING/SERVICE .................. BACK PAGE

INDEX

Accessodes ..................................................5

Adjustments:

Brake ...................................................22

Carburetor ........................................25

Mower:

Front-To-Back .......................... 21

Side-To-Side .......................................21

Throttle Control Cable ....................24

Air Filter, Engine .......................................18

Air Screen, Engine .................................18

Assembly .......................................................7-9

Battery:

Charging .............................................. 8

Cleaning ............................................17

Starting with Weak Battery .............23

Storage ..........................................................26

Terminals ...........................................17

Belts:

Motion Drive

Removal/Replacement ...............22

Mower Blade Drive

Removal/Replacement ...............22

Biade:

Sharpening .............................................16

Replacement .................................. 16

Brake Adjustment ..........................................22

Cmburetor Adjustment ................................25

Controls, Tractor ...........................................11

Customer Responsibilities ............. 15-19

Engine:

Air Filter .................................. 18

Air Screen, Engine ...........................18

Battery ............................................17

Cooling Fins, Engine ..................18

Engine Oil .......................................17

Fuel Filter .........................................19

Spark Plugs ....................................19

Tractor:

Blades ..............................................16

Lubrication Chart ...................... t 5

Maintenance Schedule ................15

Tire Care ..................................9,16,23

Cutting Height, Mower ............................ 12

Electrical:

Interlocks and Relays ................. 24

Schematic .........................................29

Wiring Diagram .......................... 30

Engine:

Air Filter, ...................................................18

Air Screen ............................................! 8

Cooling Fins, Engine .........................18

Oil Change ..................................................17

Oil Level ........................................13,17

Oil Type ............................................. 17

Preparation ..................................... 13

Repair Parts ......................................48-53

Starting ...............................................14

Storage ..............................................26

Fiffers:

Air ..................................................... 18

Fuel ...............................................................19

Fuel:

Type ................................................. 13

Storage .......................................................26

Fuse ..........................................................................24

Gauge Wheels ............................................. 9

Hood Removal/Installation ........................24

Leveling Mower Deck ..................... 21

Lubrication Chart .................................... 15

Maintenance Schedule ....................................15

Mower:

Adjustment, Front4o-Back ..............21

Adjustment, Side-to-Side ...............21

Blade Sharpening ............................... 16

Blade Replacement ........................ 16

Cutting Height .............................................12

Installation ................................................20

Operation ...................................... 13

Removal ..............................................20

Mowing Tips ...................................................... 14

Muffler, .........................................................I9

Spark Arrester ........................... 3,40

Mulcher Plate ......................................................9

Oil:

Cold Weather Conditions ....... 13,17

Engine ........................................................17

Storage ............................................ 26

Operation ................................................10-14

Operating Mower .......................................13

Options:

Accessories ...............................................5

Spark Arrester .................:................3,40

Parking Brake .....................................11-12

Parts Bag ...........................................................6

Parts, Replacement/Repair ..............30-47

Product Specifications ................................3

Repair Parts ..........................................30-47

Safety Rules ....................................................2

Seat ....................................................................... 8

Service and Adjustments ......................20-25

Brake ................................................................22

Carburetor ....................................................25

Fuse ........................................................24

Hood Removal/Installation .......... 24

Motion Drive Belt

RemovaVReplacement .............22

Mower Blade Drive Belt

Removal/Replacement ......... 22

Mower Adjustment:

Front-to-Back ............................ 21

Side-to-Side .....................................21

Mower Installation .......................... 20

Mower Removal ................................20

Tire Care ..................................9,16,23

Slope Guide Sheet ...................................... 55

Spark Plugs .............................................. 19

Specifications ..................................................3

Starting the Engine .............................13-14

Steedng Wheel ........................................7,23

Stopping the Tractor ............................... 12

Storage ..................................................... 26

Throttle Control Cable Adjustment ..... 24

Tires ............................................................9,16,23

Trouble Shooting Chart .........................27-28

Transaxle Repair Parts ......................46*47

Warranty ......................................................3

Wiring Diagram .............................................. 30

Wiring Schematic .....................................29

ACCESSO ES ANDATTACH ENTS

These accessories and attachments were available through most Sears retait outlets and service centers when the tractor was purchased Most Sears stores can order these items for you when you provide the model number of your tractor

ENGINE

SPARK PLUG GAS CAN

ENGINE OIL FUEL STABILIZER AIR FILTER

MAINTENANCE

BLADES BELTS

PERFORMANCE

Sears offers a wide variety of attachments that fit your tractor Many of these are listed below with brief explanations of how they can help you This list was current at the time of publication; however, it may change in future years - more attachments may be added changes may be made in these attachments, or some may no longer be avai abe or f t your model Contact your nearest Sears store for the accessories and attachments that are available for your tractor.

Most of these attachments do not require additional hitches or conversion kits (those that do are indicated) and are designed for easy attaching and detaching

AERATOR promotes deep root growth for a healthy lawn. Ta- pered 2o5-inch steel spikes mounted on 10-inch diameter discs puncture holes in soil at close intervals to let moisture soak in Steel weight tray for increased penetration.

BAGGER lets you collect grass clippings and leaves for a healthier, heater looking lawn Two Permanex containers hold 30-gallon plastic bags

BUMPER protects front end of tractor from damage CARTS make hauling easy Variety of sizes available, plus

accessories such as side panel kits, tool caddy, cad cover, protective mat and dolly

CORING AERATOR takes small plugs out of soil to allow mois- ture and nutrients to reach grass roots 36-inch swath. 24

hardened steel coring tips. t50 tb capacity weight tray. EASY OIL DRAIN VALVE makes oil changes easier, faster. FRONT NOSE ROLLER canters in front of mower deck to reduce

chances of "scalping" on uneven terrain. GANG HITCH lets you tow 2 or 3 pull-behind attachments at once,

such as sweepers, dethatchers, aerators (not for use with rollers, carts or other heavy attachments)

GAUGE WHEELS on both sides of the mower deck reduce chances of "scalping" on uneven terrain F0r mower decks not so

equipped, MULCH RAKEJDETHATCHER loosens soil and flips thatch and

matted leaves to lawn surface for easy pickup Twenty spring tine teeth.. Useful to prepare bare areas for seeding. Available for front or rear mounting. HIGH PERFORMANCE REEL-ACTION SPRING TtNE DETHATCHER covers 36-inch wide path and tosses thatch into large hopper Mounts behind tractor.

MULCHING CLOSE-OUT PLATE KIT, once installed, lets you mulch, discharge or bag clippings (bagger optional) without changing blades For models not equipped as 3-in-1 Convertible mowers See "MOWER" in the Repair Parts section of this

manual. RAMP TOPS AND FEET let you load and unload tractor from a

pickup truck. Use with 2 x 8 or 2 x 10 lumber ROLLER for smoother lawn surface. 36-inch wide, 18-inch

diameterwater-tightdrumholdsupto390Ibs ofweight Rounded edges prevent harm to turf Adjustable scraper automatically

cleans drum

SNOW BLADE for snow removal only. 14-inch high, 48-inch wide bfade clears 42-inch path when angled teft or right Raises, lowers with side lever Adjustable skids; replaceable, reversible scraper bar (Use with tire chains and wheeI weights and/or rear drawbar weight )

SNOWTHROWER has 40-inch swath Drum-type auger handles powdery and wet/heavy snow Mounts easily with simple pin arrangement. Discharge chute adjusts from tractor seat 6-inch diameter spout discharges snow 10 to 50 feet Lift controlled at

tractor seat. (Use with chains and wheel weights and!or rear

drawbar weight ) SPRAYERS use 12-volt DC electric motor that connects to the

tractor battery or other 12-volt source Includes booms for

automatic spraying and hand held wand for spot spraying Wand has adjustable spray pattern For applying herbicides, insecti-

cides, fungicides and liquid fertilizers

SPREADERISEEDERS make seeding, fertilizing, and weed kill- ing easy. Broadcast spreaders are also useful for granular de-

icers and sand SWEEPERS let you collect grass clippings and leaves

TILLER has 5 hp engine and 36-[nch swath to prepare seed beds, cultivate and compost garden residue. Tiller has its own built-in

lift and depth controt system and does NOT require a sleeve hitch

Fits any lawn, yard or garden tractor Simply hook up to thetractor drawbar and go! Optional accessories convert unit for dethatching, aerating, hilling without tools

TIRE CHAINS are heavy duty; closely spaced extra-large cross

links give smooth ride, outstanding traction TRACTOR CAB has heavy duty vinyl fabric over tubular steel

frame, ABS plastic top; ctear plastic windshield offers 360 degree visibility. Hinged metal doors with catch. Keeps operator warm

and dry Remove vinyl sides and windshields for use as sun protector in summer Optional accessories include; tinted! tempered solid safety glass windshield with hand operated wiper;

12-volt amber caution Iight for mounting on cab top° VACS for powerful collection of heavy grass clippings and leaves

Optional wand attachment to pick up debris in hard-to-reach

places VAC/CHIPPER includes a chipper-shredder WEIGHT BRACKET for drawbar for snow removal applications

Uses (t) 55 Ib weight

WHEEL WEIGHTS for rear wheels provide needed traction for

snow removal or dozing heavy materials

i -- -- =

CONTENTS OF HARDWARE PACK

Parts Bag contents shown full size

1) Large Flat Washer

(1) Locknut

5/16-18

(1) Locknut

3/8-24

(1) Hex Bolt

5/16-18 x t-1/4

(1) Shoulder Bolt

5/16-18

(1) Hex Bolt

_ N N _

(1) Lock Washer 1/2

(1) Washer

17/32 x 1-3/16 x 12 Gauge

#10 x 5/8 (2) Lock Washers #10

.........._(2) Washers

(2) Weld Nuts #10 _ I

,RJ

3/16 x 3/4 x 16 Gauge

, ix ut,@

O "

(2) Washers@

__ 9/32 x 5/8 x16 Gauge (2) Lock Washers 1/4

Parts packed separately in carton

Seat

Video

Cassette

Steering

Wheel

Mulcher

Plate

Manual

Steering

Boot

Parts Bag

(2) Shoulder

Bolts

Steering Wheel

Adapter

Parts bag contents not shown full size

2) Washers 318

x 7/8 x 14 Gauge

_ok

Assemblys

Slope Sheet

(2) Gauge

Wheels

Q(2) Center-

lock Nuts

,,_'k_!Swteering

heel

Insert

I teering

Extension Shaft

(2) Keys

ASSEMBLY

i l i i iH,i i,, i i lllll ,mmll,l l ,, ,,m ...................

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use

the correct tools as necessary to insure proper tightness,

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier Standard wrench sizes are listed.

(1) 5/16" wrench (1) 3/4" Socket w/drive rachet (2) 7/16" wrenches Phillips Screwdriver (1) 112" wrench Tire pressure gauge (1) 9/16" wrench Utility knife When right or left hand is mentioned in this manual, it

means when you are in the operating position (seated behind the steering wheel)

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

• Remove all accessible loose parts and parts cartons from carton (See page 6),

- Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

o Check for any additional loose parts or cartons and

remove.

BEFORE ROLLING TRACTOR OFF SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

o Slide extension shaft onto lower steering shaft.. Align

mounting holes in extention and lower shafts and install 5/16 hex bolt and Iocknut Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY

TQ 18-22 FT. LBS TORQUE,

• Place tabs of steering boot over tab slots in dash and push down to secure,.

INSTALL STEERING WHEEL

o Position front wheels of the tractor so they are pointing

straight forward

o Slide steering wheel adapter onto steering shaft extem

stono

. Position steering wheel and sleeve assembly so cross

bars are horizontal (left to right) and slide onto adapter°

o Assemble large flat washer and 3/8-24 tocknut and

tighten securely.

• Snap steering wheel insert into center of steering

wheel

o Remove protective plastic from tractor hood and grill

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID

TO ROLL TRACTOR OFF SKID (See Fig. 8)

o Raise attachment lift lever to its highest position o Release parking brake by depressing clutch/brake

pedal o Place gearshift lever in neutral (N) position, ,' Roll tractor backwards off skid.,

o Remove banding holding discharge guard up against

tractor.. 7

FIG, 1

HOW TO SET UP YOUR TRACTOR

CONNECT BATTERY (See Figs. 2 and 3)

CAUTION: Do not short battery termi- nals. Before connecting battery, re- move metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acciden- tal grounding.

• Remove cardboard packing from seat pan and lift seat pan to raised position

o Open battery box door. o Remove terminal protective caps and discard o If this battery is put into service after month and year

indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps.

o First connect RED battery cable to positive (+) terminal

with hex bolt, flat washer, lock washer and hex nut as shown Tighten securely

o Connect BLACK grounding cable to negative (-) termi-

na! with remaining hex bolt, flat washer, lock washer and hex nut Tighten securely

= Close battery box door

ASS

Open battery box doer for': . Inspection for' secure connections (to tighten hard-

ware)_ . Inspection for corrosion, ° Testing battery o Jumping (if required), ° Periodic charging

DISCARD TERMINAL

POSITIVE PROTECTIVE (RED) CABLE CAPS

HEX

NUT

LOCK WASHER

FLAT WASHER

NEGATIVE

(SLACK) CABLE

FIG. 2

SEAT PAN

BATTER _

BOX DOOR

FIG, 3

INSTALL SEAT (See Fig. 4) Adjust seat before tightening adjustment boil = Remove cardboard packing on seat pan.

SEAT PAN

HEX

BOLT

SHOULDER BOLT

ADJUSTMENT

BOLT

SEAT

LOCK WASHER

LARGE FLAT WASHER

The tires on your tractor were ovednflated at the factory for

shipping purposes. Correct tire pressure is important for best cutting performance.

o Reduce tire pressure to PSI shown in "PRODUCT

SPECIFICATIONS" on page 3 of this manual.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be properly

leveled. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual°

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for reptacing motion and

mower blade drive belts in the Service and Adjustments

section of this manual Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your' tractor, check to see that the brake is properly adjusted, See "TO ADJUST

BRAKE" in the Service and Adjustments section of this manual

ASSEMBLE GAUGE WHEELS TO MOWER

° Place seat on seat pan and assemble shoulder' boll

. Assemble adjustment bolt, lock washer and flatwasher

loosely. Do not tighten_

• Tighten shoulder bolt securely.

• Lower seat into operating position and sit on seat. . Slide seat until a comfortable position is reached which

allows you to press clutch/brake pedal all the way down,

• Get off seat without moving its adjusted position. ° Raise seat and tighten adjustment bolt securely,

DECK (See Fig. 5)

Assemble gauge wheels with tractor on a flat level surface.

• Adjust mower' to desff'ed cutting height (See 'q-o AD- JUST MOWER CUTTING HEIGHT" in the Operation

section of this manual).

- With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the

ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8" washer and 3/8-16 Iocknut and

tighten securely.

- Repeat for opposite side installing gauge wheel in same adjustment hole..

CHECK TIRE PRESSURE

FIG. 4

GAUGE WHEEL MOUNTING

LOCKNUT

318" WASHER

GAUGE WHEEL'

ASSEMBLY

,,i,,,i,,llm i i,i ill ,ll

TO CONVERT TO BAGGING OR

DISCHARGING

Simply remove mulcher plate and store in a sate place. Your mower is now ready for discharging or installation of optional grass catcher accessory,

NOTE: Itis not necessary to change blades° The mulcher blades are designed for discharging and bagging also.

SHOULDER BOLT

FIG. 5

INSTALL MULCHER PLATE (See Figs, 6 & 7)

• install two latch hooks to mutcher plate using screw, washer, lock washer, and we}d nut as shown

NOTE: Pre-assemble weld nut to latch hook by inserting weld nut from the top with hook pointing down.

= Tighten hardware securely, ° Raise and hold deflector shield in upright position . Place front of mulcher plate over front of mower deck

opening and slide into place, as shown..

° Hook front latch into hole on front of mower deck = Hook rear latch into hole on back of mower deck

CAUTION: Do not remove discharge

guard from mower, Raise and hold guard when attaching mulcher plate and allow it to rest on plate while in operation.

WELD NUT FROM THE TOP

LOCK

WELD WASHER

NUT _ SCREW

LATCH

WASHER

HOOK POINTS DOWN

LOCK

WASHER

__-...--_SCREW

HOOK

WELD NUT

FIG, 6

MULCHER

PLATE

DEFLECTOR

SHIELD

LATCH HOOKS

FIG, 7

,/CHECKL IS T

BEFORE YOU OPERATE AND ENJOY YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCEAND SA TISFACTION FROM THIS QUALITY PRODUCT

PLEASE REWEW THE FOLLOWING CHECKLIST"

v" All assembly instructions have been completed..

,,/ No remaining loose parts in carton. v" Battery is properly prepared and charged.. (Minimum

1 hour at 6 amps) ,/ Seat is adjusted comfortably and tightened securely. ¢" Al! tires are properly inflated. (For shipping purposes,

the tires were overinflated at the factory).

¢" Be sure mower deck is properly leveled side-to-side/

front-to-rear for best cutting results. (Tires must be properly inflated for leveling)

v" Check mower and drive belts. Be sure they are routed

properly around pulleys and inside all belt keepers

,/ Check wiring. See that all connections are still secure

and wires are properly clamped.

WHILE LEARNING HOWTO USE YOUR TRACTOR, PAY EXTRA A TTENTION TO THE FOLL OWING IMPORTANT ITEMS.:

v" Engine oil is at proper level

,/ Fuel tank is filled with fresh, clean, regular unleaded

gasoline..

,/ Become familiar with at! controls - their location and

function. Operate them before you start the engine

,/ Be sure brake system is in safe operating condition..

+ 21 hidden pages

Craftsman 937.256541 Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual