Craftsman 917773708 Owner’s Manual

Owner's Manual

CRIIFTSMRN°

WHEEl. ED WEEDTRIMMER

6.0 Horsepower 22 Inch Cut

Model No.

917.773708

• Espahol, p. 17

_IbCAUTION:

Read and follow all

Safety Rules and Instructions before operating this equipment.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

Visit our Craftsman website: www.sears.com/craftsman

U.S.A.

Warranty ................................................... 2

Safety Rules .......................................... 2-4

Product Specifications .............................. 5

Assembly / Pre-Operation ........................ 5

Operation ............................................... 6-8

Maintenance Schedule ............................. 9

Maintenance ........................................ 9-11

Service and Adjustments ................... 12-13

Storage ................................................... 14

Troubleshooting ...................................... 15

Repair Parts ....................................... 32-39

Sears Service .......................... Back Cover

LIMITED TWO YEAR WARRANTY ON CRAFTSMAN WEEDTRIMMER

For two (2) years from date of purchase, when this Craftsman Weedtrimmer is main- tained, lubricated, and tuned up according to the operating and maintenance instruc- tions in the owner's manual, Sears will repair free of charge any defect in material or

workmanship.

If this Craftsman Weedtrimmer is used for commercial or rental purposes, this warranty

applies for only 90 days from the date of purchase. This Warranty does not cover:

• Expendable items which become worn during normal use, such as rotating lines,

belts, air cleaners and spark plug.

• Repairs necessary because of operator abuse or negligence, including bent crank-

shafts and the failure to maintain the equipment according to the instructions con- tained in the owner's manual.

Warranty service is available by returning the Craftsman Weedtrimmer to the nearest

Sears Parts & Repair Center in the United States. This warranty applies only while this

product is used in the United States. This Warranty gives you specific legal rights, and you may also have other rights which

vary from state to state.

Sears, Roebuck and Co., Dept. 817 WA, Hoffman Estates, IL 60179

_, WARNING: This trimmer is equipped with an internal combustion engine and should

not be used on or near any unimproved forest-covered, brush-covered or grass-covered

land unless the engine's exhaust system is equipped with a spark arrester meeting ap-

plicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

In the state of California the above is required by law (Section 4442 of the California

Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest Sears

service center (see the REPAIR PARTS section of this manual).

The operation of any trimmer can result in foreign objects thrown into

SAFETYGLASSES

the eyes, which can result in severe eye damage. Always wear safety

glasses or eye shields while operating your trimmer or performing any adjustments or repairs. We recommend standard safety glasses or a

wide vision safety mask worn over spectacles.

_IbLook for this symbol to point out

important safety precautions. It means

CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

A WARNING: In order to prevent ac- cidental starting when setting up, trans- porting, adjusting or making repairs,

always disconnect spark plug wire and

2 place wire where it cannot contact plug.

AWARNING: Engineexhaust, some

of its constituents, and certain vehicle

components contain or emit chemicals

known to the State of California to

cause cancer and birth defects or other

reproductive harm.

CAUTION: Muffler and other engine parts become extremely hot during operation and remain hot after engine has

stopped. To avoid severe burns on contact, stay away from these areas.

I. GENERAL OPERATION

• Read, understand, and follow all instruc- tions on the machine and in the manual

before starting. Be thoroughly familiar with the controls and the proper use of

the machine before starting.

• Do not put hands or feet near or under rotating parts.

• Keep all parts of your body away from muffler and spinning line. A hot muffler

can cause serious burns.

• Only allow responsible individuals, who are familiar with the instructions, to

operate the machine.

• Stay away from breakable objects, such as house windows, auto glass, green-

houses, etc.

• Clear the area of objects such as rocks, toys, wire, bones, sticks, etc., which

could be picked up and thrown by the spinning lines.

• Be sure the area is clear of other people before trimming, particularly small chil-

dren and pets. Stop machine if anyone enters the area.

• Wear appropriate clothing such as a long-sleeved shirt or jacket. Also wear long trousers or slacks. Do not wear

shorts.

• Do not wear loose clothing which could get caught in this equipment.

• Do not operate the machine when bare- foot or wearing open sandals. Always

wear work gloves and sturdy footwear. Leather work shoes or short boots work

well for most people. These will protect the operator's ankles and shins from small sticks, splinters, and other debris,

and improve traction.

• Do not pull machine backwards unless ab- solutely necessary. Always look down and behind before andwhile moving backwards.

• Do not operate the machine without proper guards, plates or other safety protective devices in place.

• See manufacturer's instructions for proper operation and installation of

accessories. Only use accessories ap- proved by the manufacturer.

• Never use blades, wire, or flailing devices.

This unit is designed for line trimmer use

only. Use of other accessories or attach- ments will increase the risk of injury.

• Stop the rotating trimmer head when

crossing gravel drives, walks, or roads. Wait for the cutting lines to stop rotating.

• Stop the engine (motor) whenever you leave the equipment and allow it to cool,

before cleaning, repairing or inspecting

the unit. Be sure the trimmer head and

all moving parts have stopped.

• Operate only in daylight or good artificial light.

• Do not operate the machine while under

the influence of alcohol or drugs.

• Never operate machine in wet grass. Al-

ways be sure of your footing: keep a firm

hold on the handle and walk; never run.

• If the equipment should start to vibrate abnormally, stop the engine (motor) and

check immediately for the cause. Vibra- tion is generally a warning of trouble.

• Always wear safety goggles or safety glasses with side shields when oper-

ating machine.

II. SLOPE OPERATION

Slopes are a major factor related to slip and fall accidents which can result in severe injury.

All slopes require extra caution. If you feel

uneasy on a slope, do not trim it. DO:

• Trim across the face of slopes: never up and down. Exercise extreme caution

when changing direction on slopes.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Tall grass can hide obstacles.

DO NOT:

• Do not trim near drop-offs, ditches or

embankments. The operator could lose footing or balance.

• Do not trim excessively steep slopes.

• Do not trim on wet grass. Reduced foot- ing could cause slipping.

III. CHILDREN

Tragic accidents can occur if the opera- tor is not alert to the presence of chil-

dren. Children are often attracted to the machine and the trimming activity. Never

assume that children will remain where

you last saw them.

• Keep children out of the trimming area and under the watchful care of another

responsible adult.

• Be alert and turn machine off if children enter the area.

• Before and while moving backwards, look behind & down for small children.

• Never allow children to operate the machine.

• Use extra care when approaching blind corners, shrubs, trees, or other objects

that may obscure vision.

IV. SERVICE

• Use extra care in handling gasoline and other fuels. They are flammable and

vapors are explosive.

Use only an approved container.

Never remove gas cap or add fuel with with the engine running. Allow engine to cool before refueling. Don't smoke.

Never refuel the machine indoors. Never store the machine or fuel

container inside where there is an open flame, such as a water heater.

Move away from fueling site before starting engine.

• Never run trimmer inside a closed area.

• Never make adjustments or repairs with the engine (motor) running. Disconnect

the spark plug wire, and keep the wire away from the spark plug to prevent ac- cidental starting.

• Keep nuts and bolts, especially trimmer

head and engine bolts, tight and keep

equipment in good condition.

• Never tamper with safety devices. Check their proper operation regularly.

• Keep machine free of grass, leaves, or other debris buildup. Clean oil or fuel

spillage. Allow machine to cool before cleaning or storing.

• Stop and inspect the equipment if you strike an object. Repair, if necessary,

before restarting.

• Do not change the engine governor set- ting or overspeed the engine.

• Clean and replace safety and instruction decals as necessary.

Repair Protection

Congratulations on making a smart put- • chase. Your new Craftsman® product is

designed and manufactured for years of dependable operation. But like all prod-

ucts, it may require repair from time to

time. That's when having a Repair Protec- tion Agreement can save you money and

aggravation.

Purchase a Repair Protection Agreement now and protect yourself from unexpected hassle and expense.

Here's what's included in the Agreement:

• Expert service by our 12,000 profe- sional repair specialists.

• Unlimited service and no charge for parts and labor on all covered repairs.

• Product replacement if your covered product can't be fixed.

• Discount of 10% from regular price of service and service-related parts not

covered by the agreement; also, 10%

off regular price of preventive mainte- nance check.

Agreements

Fast help by phone - phone support

from a Sears technician on products

requiring in-home repair, plus conve- nient repair scheduling.

Once you purchase the Agreement, a simple phone call is all that it takes for you

to schedule service. You can call anytime day or night, or schedule a service ap-

pointment online. Sears has over 12,000 professional repair specialists, who have access to over 4.5

million quality parts and accessories. That's the kind of professionalism you can count on to help prolong the life of your

new purchase for years to come. Purchase your Repair Protection Agreement today!

Some limitations and exclusions apply. For prices and additional information

call 1-800-827-6655.

Sears Installation Service

For Sears professional installation of home

appliances, garage door openers, water heaters, and other major home items, in

the U.S.A. call 1-800-4-MY-HOME®.

SerialNumber: DateofPurchase:

GasolineCapacity/Type: 1.6Quarts(UnleadedRegular) OilType(APISG-SL): SAE30(above32°F);SAE5W-30(below32°F) OilCapacity: 20 Ounces SparkPlug(Gap: .030") ChampionRJ19LMor J19LM

TrimmerLine Length: 18.75Inches(0.155 InchDiameter)

• The modelandserialnumberswillbe foundona decalon the rear ofthetrimmer. Recordbothserialnumberanddateof purchasein thespaceprovidedabove.

Readtheseinstructionsandthismanualin itsentiretybeforeyou attemptto assemble

oroperateyour newtrimmer. IMPORTANT:ThistrimmerisshippedWITH-

OUTOILORGASOLINEintheengine.

Yournew trimmerhasbeenassembled

atthefactorywith the exceptionof those partsleftunassembledfor shipping purposes.All partssuch as nuts,wash-

ers, bolts,etc., necessarytocompletethe

assemblyhavebeen placedinthe parts bag. Toensuresafeandproperoperation

ofyourtrimmer,all partsand hardware

you assemblemustbe tightenedsecurely.

Usethecorrecttoolsas necessaryto

ensurepropertightness. When righthand(RH)orleft hand(LH)is

mentionedin this manual,it meanswhen

you are intheoperatingposition(standing

behindthehandle). LoosePartsPackedSeparately

HOW TO SET UP YOUR TRIMMER

TO UNFOLD HANDLE

IMPORTANT: Unfold handle carefully so

as not to pinch or damage control cables.

1. Loosen handle knob enough to allow upper handle to be unfolded from the

shipping position.

2. Raise upper handle section into place on lower handle and tighten handle knob.

3. Remove handle padding holding trim- mer head control bar to upper handle.

Your trimmer handle can be adjusted for your trimming comfort. Refer to "ADJUST

HANDLE" in the Service and Adjustments

section of this manual.

Upper handle

Bottle of oil

REMOVE TRIMMER FROM CARTON

1. Remove loose parts included with trimmer.

2. Cut down two end corners of carton and lay end panel down flat.

3. Remove all packing materials.

4. Roll trimmer out of carton and check car- ton thoroughly for additional loose parts.

Trimmer Lines (2) Sets

(0.155 diameter

x 18.75 inches long)

LIFT UP

Handle

knob

Lower

handle

KNOW YOUR TRIMMER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING

YOUR TRIMMER. Compare the illustrations with your trimmer to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.

These symbols may appear on your trimmer or in literature supplied with the product. Learn and understand their meaning.

CAUTION ENGINE OFFFAST SLOW FUEL OIL

/A WARNING G

Throttle control

Starter handle

AVOIDSERIOUS

INJURYORDEATH

Trimmer head control bar

Engine oil cap

with dipstick

Handle knob

Gasoline cap i

Primer

IMPORTANT: This trimmer is shipped

WITHOUT OIL OR GASOLINE in the engine. Trimmer head control bar - must be held

down to the handle to engage trimmer head. Release to stop the trimmer head.

Primer - pumps additional fuel from the

carburetor to the cylinder for use when

starting a cold engine.

Muffler

Chassis cover

__ Trimmer head

__==_/Trimmer line

Throttle control - used for starting and stopping the engine and allows you to se-

lect either FAST or SLOW engine speed. Starter handle - used for starting the

engine.

SAFETYGLASSES

The operation of any trimmer can result in foreign objects being thrown into the eyes, which can result in severe eye damage.

Always wear safety glasses or eye shields while operating your trimmer or performing

any adjustments or repairs. We recom- mend standard safety glasses or a wide

vision safety mask worn over spectacles.

HOW TO USE YOUR TRIMMER ENGINE SPEED

The engine speed is controlled by a throt- tle located on the side of the upper handle.

FAST position is for starting and normal

trimming. SLOW is for light trimming and fuel economy. STOP is for stopping the engine.

TO ADJUST TRIMMING HEIGHT

_CAUTION: Stop the engine and wait for all moving parts to stop. Disconnect spark

plug wire from spark plug and place wire

where it cannot come in contact with plug. The height of cut can be set to six (6) dif-

ferent positions ranging from 1-1/2 inches to 3 inches. Recommended cutting height

for the average yard is 2 inches.

1. To adjust trimming height, push in the locking plate tab and move trimmer

head up or down to desired position.

2. Release tab and be sure head is locked into one of the six (6) height

positions.

Adj

Trimmer

Head

Locking Plate Tab

SLOW

FAST

TRIMMER HEAD DRIVE CONTROL Your trimmer is equipped with a trimmer

head drive control bar which will require the operator to be positioned behind the trimmer handle to operate the trimmer.

• Trimmer head rotation is controlled by

holding the trimmer head control bar down to the handle.

• Trimmer head rotation will stop when

the control bar is released.

BEFORE STARTING ENGINE

ADD OIL

Your trimmer is shipped without oil in the engine. For type and grade of oil to use,

see "ENGINE" in the Maintenance section of this manual.

A CAUTION: DO NOT overfill engine with oil, or it will smoke heavily from the muffler on startup.

1. Be sure trimmer is level.

2. Remove oil dipstick from oil fill spout.

3. You receive a container of oil with the unit. Slowly pour the entire container

down the oil fill spout into the engine.

4. Insert and tighten dipstick.

IMPORTANT:

• Check oil level before each use. Add oil

if needed. Fill to full line on dipstick.

• Change the oil after every 25 hours of

operation or each season. You may need to change the oil more often under

dusty, dirty conditions.

ADD GASOLINE

• Fill fuel tank to bottom of gas tank

filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a

minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quanti-

ties that can be used within 30 days to assure fuel freshness.

_, CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline

near an open flame.

_CAUTION: Alcohol blended fuels

(called gasohol or using ethanol or methanol) can attract moisture which

leads to separation and formation of acids during storage. Acidic gas can damage

the fuel system of an engine while in

storage. To avoid engine problems, the

fuel system should be emptied before

storage of 30 days or longer. Empty

the gas tank, start the engine and let it

run until the fuel lines and carburetor are empty. Use fresh fuel next season.

See Storage Instructions for additional information. Never use engine or

carburetor cleaner products in the fuel tank or permanent damage may occur.

NOTE: In cooler weather it may be necessary to repeat priming steps. In

warmer weather overpriming may cause flooding and engine will not start. If you do flood engine, wait a few minutes before

attempting to start and do not repeat priming steps.

Gasoline filler Engine

ca oil cap

Primer

TO STOP ENGINE

• To stop engine, move throttle control

lever to STOP position.

TO START ENGINE

1. To start a cold engine, push primer three (3) times before trying to start. Use a

firm push. This step is not usually neces-

sary when starting an engine which has already run for a few minutes.

2. Move throttle control lever to FAST position.

3. Hold upper handle firmly and pull starter handle quickly. Do not allow

starter rope to snap back.

TRIMMING TIPS

• Set the throttle control in the FAST posi-

tion. If the weeds or grass are tall and thick, operate the trimmer at a slower walking speed.

• Frequently clean the underside of the trimmer to remove any grass build up.

Keep top of engine around starter clear

and clean of grass clippings and chaff. This will help engine air flow and extend engine life.

• For best results and longer lasting line, use the ends of the line to do the cutting.

This is easily done by moving slowly through very thick and heavy weeds.

• Use the left side of trimmer when trim- ming along fences, walls, flowerbeds

and other such objects.

• If trimmer lines become too short, it will

take longer to complete the job. If trim-

mer lines are worn to less than half their original length, they should be replaced.

See "TO REPLACE TRIMMER LINE" in

the Maintenance section of this manual.

• Trimmer head contact with concrete, as- phalt or other hard surfaces may cause

premature wear of the ball on bottom of

trimmer head.

MAINTENANCE

F,LL,NDATES

AS OUOOMPLETE

REGULARSERVICE /__/_/%'4 _£'_%'4S/'_" / DATES

Check for Loose Fasteners I_ k#'

T Clean Trimmer _ I_

M_ Clean Under Engine Cover t,/'2 If

Check Drive Belt / Pulleys tf

R Check / Replace Trimmer Lines 1_3

Check Engine Oil Level I_

E Change Engine Oil 5/'1,2

Clean Air Filter I_ 2

II Inspect Muffler I_

Clean or Replace Spark Plug Replace Air Filter Paper Cartridge 1_2

1 - Change moreoften when operating under a heavyload or in highambient temperatures. 2 - Service more often whenoperating in dirtyor dusty conditions.

3 - Replace trimmerlines whenthey have worn to halftheir original length.

GENERAL RECOMMENDATIONS

The warranty on this trimmer does not cover items that have been subjected to

operator abuse or negligence. To receive

full value from the warranty, operator must

maintain trimmer as instructed in this manual.

Some adjustments will need to be made periodically to properly maintain your unit.

At least once a season, check to see if you should make any of the adjustments

described in the Service and Adjustments section of this manual.

• At least once a year, replace the spark plug and replace air filter element. A

new spark plug and clean/new air filter element assure proper air-fuel mixture and help your engine run better and

last longer.

• Follow the maintenance schedule in this manual.

BEFORE EACH USE

1. Check engine oil level.

2. Check for loose fasteners.

3. Clean under engine cover.

LUBRICATION

To prolong the useful life of your trimmer, change engine oil as recommended in this

section of Owner's Manual.

IMPORTANT: Do not oil or grease plastic

wheel bearings. Viscous lubricants will attract dust and dirt that will shorten the

life of the self- lubricating bearings. If you

feel they must be lubricated, use only a dry,

powdered graphite type lubricant sparingly.

TRIMMER

Always observe safety rules when per- forming any maintenance.

TIRES

• Keep tires free of gasoline, oil, or insect control chemicals which can harm rub-

ber.

• Avoid stumps, stones, deep ruts, sharp objects and other hazards that may

cause tire damage.

TRIMMER LINE

For best results, replace trimmer lines

when they have worn to half their original

length. Use .155 inch diameter trimmer line. Cut new trimmer line length to 18-3/4

inches. After new line is installed on

trimmer head, check all lines so they do

not vary more then one (1) inch in length.

This is important to make sure the trim-

mer head is balanced and will not vibrate abnormally.

_WARNING: Use only the specified trimmer line. Do not use other materials

such as wire, string, rope, etc. Wire can break off during trimming and become a dangerous missile that can cause serious

injury.

TO CUT LINE TO PROPER LENGTH

NOTE: Trimmer line pre-cut to proper length is available for this unit; see the Repair Parts section of this manual.

If trimmer line is purchased in bulk, it must be cut to 18-3/4 inches before using. Use

the built-in length guage as follows:

1. From front of trimmer, place the end of spooled trimmer line at the mark on the

side of the debris shield as shown.

2. Wrap trimmer line around front of chas- sis cover to other side and cut at the

"22" mark (your unit's width of cut).

TO REPLACE TRIMMER LINE

1. Disconnect spark plug wire from spark plug and place wire where it cannot

come in contact with spark plug.

2. Remove worn trimmer line from line carrier plate.

3. Fold new, cut to length, trimmer line

in half and insert folded end through

carrier plate opening to back side of

retainer clip.

4. With folded end of line at back side of

retainer clip, pull line outward until line is fully seated under the retainer clip.

5. Repeat on other side of carrier plate.

6. Check all lines to be sure they are the same length.

7. Reconnect spark plug wire to spark

plug.

Trimmer

line

Chassis cover

WRAP

LINE

AROUND

Debris New shield End of trimmer

mark spooled line line

Carrier plate opening

\ /

Retainer

clip

ENGINE

LUBRICATION

Use only high quality detergent oil rated

with API service classification SG-SL.

Select the oil's SAE viscosity grade according to your expected operating

temperature.

SAE VISCOSITY GRADES

F -20 0 30 32 40 60 80

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)improve starting in

cold weather, these multi-viscosity oils will

result in increased oil consumption when used above 32°F. Check your engine oil

level more frequently to avoid possible

engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the unit is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5)

hours of continuous use. Tighten oil plug securely each time you check the oil level.

TO CHANGE ENGINE OIL

NOTE: Before tipping trimmer to drain oil, drain fuel tank by running engine until fuel

tank is empty.

1. Disconnect spark plug wire from spark plug and place wire where it cannot

come in contact with spark plug.

2. Remove engine oil cap; lay aside on a clean surface.

3. Tip trimmer on its side as shown and drain oil into a suitable container. Rock

trimmer back and forth to remove any oil trapped inside of engine.

Container

4. Wipe off any spilled oil from trimmer or side of engine.

5. Fill engine with oil (See "ADD OI1" in the Operation section of this manual).

6. Replace engine oil cap.

7. Reconnect spark plug wire to spark plug.

AIR FILTER Your engine will not run properly and may

be damaged by using a dirty air filter. Replace the air filter cartridge every 100

hours of operation or every season, which-

ever occurs first. Service air cleaner more often under dusty conditions. TO CLEAN AIR FILTER

1. Loosen screw and tilt cover to remove.

2. Carefully remove cartridge.

3. Clean by gently tapping on a flat sur-

face. If very dirty, replace cartridge.

AI_CAUTION: Petroleum solvents, such as kerosene, are not to be used to clean cartridge. They may cause deterioration

of the cartridge. Do not oil cartridge. Do

not use pressurized air to clean or dry

cartridge.

4. Install cartridge, then replace cover making sure the tabs are aligned with

the slots in the back plate. Fasten screw securely.

Back plate

Cartridge

MUFFLER Inspect and replace corroded muffler as it

could create a fire hazard and/or damage. SPARK PLUG

Replace spark plug at the beginning of

each mowing season or after every 100

hours of operation, whichever occurs

first. Spark plug type and gap setting are shown in the "PRODUCT SPECIFIC-

ATIONS" section of this manual.

CLEANING

IMPORTANT: For best performance, keep

trimmer free of built-up grass and trash. Clean the underside of your trimmer after

each use.

Slot

Cover

tab

ACAUTION: Disconnectsparkplug wire from sparkplugand placewirewhereit

cannotcomein contactwithplug.

• Turntrimmeron its side.Makesure air filterandcarburetorareup. Cleanthe

undersideofyour trimmerby scrapingto removebuild-upof grassandtrash.

• Cleanengineoftento keeptrashfrom accumulating.Acloggedengineruns

hotterandshortensenginelife.

Keepfinishedsurfacesandwheelsfree ofall gasoline,oil, etc.

We donot recommendusingagarden

hoseto cleantrimmer unlesstheelec-

trical system,muffler,air filter andcar-

buretorarecoveredto keepwaterout.

Waterinenginecan resultinshortened enginelife.

A WARNING: Toavoidseriousinjury,

beforeperforminganyserviceand adjustments:

1. Stopengine.

2. Makesuretherotatinglines andall

movingparts havecompletelystopped.

3. Disconnectsparkplugwirefromspark plugand placewirewhereit cannot

come in contactwith plug.

TRIMMER TOADJUSTTRIMMINGHEIGHT

See"TOADJUSTTRIMMINGHEIGHT"in

the Operationsectionof this manual. TO ADJUST HANDLE

Theupperhandlemay beadjustedto dif- ferentheightpositions.

• Loosenhandleknobonlyenoughto allowtheupperhandleto pivotto the desiredposition.

• Tightenhandleknobsecurely.

NOTE:The handleknobandboltmay be reversedfor left handedoperation.

Upper handle

TO REMOVE/REPLACE TRIMMER HEAD DRIVE BELT

1. Remove screw at front of chassis cove r.

2. Lift cover up and away from trimmer.

3. Remove the two (2) screws on sides of

Chassis

trimmer securing the debris shield.

4. Turn trimmer on its side with carburetor and fuel cap up.

5. Remove the two (2) screws on under- side of trimmer securing the debris

shield.

6. Slide the debris shield rearward and

remove.

7. Remove belt from engine pulley on crankshaft.

8. Remove belt from trimmer head pulley.

Handle knob

ED¢

pulley

Debris shield screws

+ 28 hidden pages